|
2.2 BIOS·How do I enter my BIOS Setup?
·How do I update my BIOS?
·How do I update my BIOS using a CD-Rom?
·How do I clear CMOS (or RTC)
·Removing Bios password.
·How to Optimize your BIOS Configuration
|
| |
Here are the most commonly used and even a alternative way to enter BIOS Setup in DOS mode.
To enter the BIOS during boot up hold down one of the following keys:
Hold down the Del key
Hold down the F1 key
Hold down the F10 key
To enter the BIOS from a DOS prompt...
(NOT from inside Windows)
Alt Ctrl Esc
Alt Ctrl Enter
Ctrl Alt A
Ctrl Alt S
Some manufacturers have their own way for entering BIOS. Here are some of the harder to find, Brand specific, ways of entering BIOS setup.
Find you computer Brand\Make below:
Acer - Ctrl+Alt+Esc
Compaq - F10
Compaq Presario - Press Alt Ctrl Esc at boot when you see the "Compaq" log in big letters
Dell - F1 or Del.
Gateway 2000 - F1
Hewlett Packard - F1
IBM
Older Models - In order to get into the configuration of the IBM setup screen (CMOS) screen you need to hold down both mouse buttons during boot-up.
Aptiva - Press F1
Leading Edge Fortiva 5000 - Ctrl Alt A or Ctrl Alt S
NEC - F2
Packard Bell - F1 or F2
Sharp Laptop 9020 - F2
Sony - F3, then F2, or F1
Tandon computers - Hold down the esc key after turning on power
Toshiba Laptops - Toshiba Utility
 feedback form
 feedback form
by DaveW$  edited by dbmaven
last modified: 2003-09-05 10:46:18 |
| |
In order to update BIOS you have to have a flash program.
Usually it is supplied by the motherboard manufacturer and
is available from their website. Along with the latest
version of the BIOS for the motherboard in a file, usually xxx.BIN although it may be called something else.
However in almost every case they will advise you to boot into DOS and run their loader program to flash/update the BIOS.
One way to do it:
•Copy their loader and BIOS update to a blank floppy.
•Make sure that your BIOS is set to boot from A: first.
•Put in a bootable DOS diskette in Drive A: and boot.
•Swap out the DOS diskette, put in the BIOS update disk
and run the update program.
If you don't have a DOS disk this is how you can make one:
•(More options are available at »www.bootdisk.com
•Download this compressed (zipped) file: MS-DOS 6.22 in executable zipped format
•Put a formatted floppy in the A: drive.
•Decompress/Unzip the contents of the file above file to your floppy
•You now have a bootable DOS diskette.
It's also a good idea to read any instructions on the manufacturers website.
feedback form
feedback form
by Awgeewhiz edited by dbmaven
last modified: 2004-06-07 20:47:51 |
| |
If your computer does not have a floppy 'A' disk drive and you want to update your BIOS, this site explains step-by-step how it can be done.
Bart's way to create bootable CD-Roms (for Windows-Dos)
This site also contains information about how to create several other types of bootable CD's, making it a great 'bookmark' addition for any serious 'hands on' computer user.
feedback form
feedback form
by DSmithLady edited by dbmaven
last modified: 2003-09-05 10:47:00 |
| |
Shut down your computer. Unplug the power cord from the power supply.
Press the power button on the front of the case to discharge any remaining charge in the Power Supply.
The green led should be off, if your motherboard has one.
Make sure you ground yourself to the case, or use an anti-static wrist strap, to reduce the static potential.
Look for a jumper near the battery, it will be labelled clrrtc, CMOS, or something similar. Consult your motherboard manual for the specifics on your board.
Some boards do not have a jumper, just two solder points that need to be bridged/shorted.
Most jumpers have three pins, with 2 of them covered. Switch the 'cover' to short the other two pins. (In other words, if Pins 2 and 3 are covered, remove the jumper and cover Pins 1 and 2). Leave the jumper in the 'clear' position for a few seconds.
Put the jumper back to its original position.
Replace power cord and try booting now.
You should (hopefully) see the bios screen, where you can choose the cpu speeds etc. f-10 to save. All BIOS settings have been reset to factory DEFAULTS by using this process!
feedback form
feedback form
by 3SGTE edited by dbmaven
last modified: 2003-09-05 10:46:31 |
| |
An alternate to leaving the battery out overnight.
Providing you can get to a DOS prompt....try holding down the shift key + F5,different combinations for different computers.
Then type the following.
at the command prompt type DEBUG then hit enter
You'll see a dash(-) at the debug prompt.
Now type o 70 2e then hit enter
Then type o 71 ff and hit enter
Then type Q and hit enter.
Reboot..... the bios password should now be gone.
NOTE: This works only with MS-DOS 6.00, ^.22 and MS-DOS 7.xx (aka Windows 9x)
feedback form
feedback form
by Cariad edited by dbmaven
last modified: 2003-09-05 11:30:33 |
| |
This is the current link to Adrian's Rojak Pot:
»www.rojakpot.com/default.aspx?location=9
This is an older version:
»www.adriansrojakpot.com/Speed_De···ndex.htm
feedback form
feedback form
by RedXII1234 edited by dragon
last modified: 2003-10-25 17:15:00 |
