·What version WRT54G(S) do I have and whats the difference?
·What alternative firmware is available?
·Where can I get Firmware/User Guide?
·What's the best firmware?
·How do I flash my WRT54G backwards?
·How do I log incoming traffic?
·How can I prevent my device from over-heating?
·Are there any hidden pages available?
·How do I set up port filtering?
·How to setup VPN on WRT54G?

Chart by jdepew

feedback form

feedback form

Any feedback you provide (corrections, updates or suggestions) are sent to the owner of this FAQ
and anyone else involved in writing or editing this item.

by Lanik
last modified: 2007-09-24 15:59:09

feedback form

feedback form

Any feedback you provide (corrections, updates or suggestions) are sent to the owner of this FAQ
and anyone else involved in writing or editing this item.

by jazzman916 edited by Lanik
last modified: 2005-06-22 00:43:38

feedback form

feedback form

Any feedback you provide (corrections, updates or suggestions) are sent to the owner of this FAQ
and anyone else involved in writing or editing this item.

by Bill edited by Lanik
last modified: 2005-06-22 00:44:12

feedback form

feedback form

Any feedback you provide (corrections, updates or suggestions) are sent to the owner of this FAQ
and anyone else involved in writing or editing this item.

by yutznut2 edited by Lanik
last modified: 2005-06-22 00:44:35

Thanks to dellsweig for instructions, full thread: /forum/remark,11974955

feedback form

feedback form

Any feedback you provide (corrections, updates or suggestions) are sent to the owner of this FAQ
and anyone else involved in writing or editing this item.

by Lanik edited by jazzman916
last modified: 2005-06-22 21:36:23

Linksys getting too hot? Here’s a solution!

What you need:

-12 marble blocks.Each should be about 1cm x 1cm, but the longest dimension should not before than 1.5cm. You can also use wood as an alternative if need be.However, the marble blocks can probably be picked up at a tile store,or maybe even a hardware store.

-A fine sandpaper. It shouldn’t be that fine though since you will need to sand down the marble a bit.

-Krazy glue. I prefer the advanced formula.

How you do it:

• Sand down each side of each block if needed.
• Glue 3 blocks together. This will make up one leg. You’ll obviously have 4 legs in total. Also, glue won’t stick well to polished surfaces.

• Sand down the edges if you want to even up the blocks a bit. Remember, don’t shorten them.
• Line the legs up,side by side, and then tape them together. You can now sand the top sand bottoms to make their heights even.
• If you want, you can put felt pads on the bottom of each leg. You can use the circular self-stick pads and then trim them.
• Glue the legs onto the bottom of your device as shown in the picture. Let the glue dry a bit before you put your device back.

You have just raised your device by about 3cm. This will allow heat to dissipate and prevent your device from overheating. Although this might seem like a bit of work, it’s well worth it.

Here is another way courtesy of AdolphHitler

Step 2.

Take your Linksys product and using the screwdriver, carefully remove its rubber feet.

Step 3.

Each rubber foot will have a small hole on the bottom with a conveniently placed piece of rubber attached by four small arms inside.
Place a thumb tack into this hole and be sure to center it.

You may notice that the thumb tack leaves a gap between the foot and its plastic handle. You can make it flush with the rubber foot by gently twisting it in as if you were driving a screw.
Do this for all four feet.

Why tacks?

The properties of the tack are perfect for this particular project because:

- It has a needle which will puncture the rubber and hold to it.

- They are cheap and easy to obtain.

- When the tack is placed inside the foot holder, its height is perfect.

- It allows the rubber foot's lip inside the holder whilst keeping the rest of the foot out as its plastic grip doesn't allow for the foot to move inside further.

Step 4.

The hard part -

Hold your Linksys product in your lap for added stability and precision.
Insert the foot upside down, rounded part first, into its holder.



Using your finger nails, carefully force the rubber lip of the foot inside. Once the whole lip is inside, adjust it with your fingers. DO NOT USE YOUR FINGERS ON THE TOPS OF THE FEET. If you do so, you will experience a thumb tack entering your finger.



Step 5.

Place the Linksys product on a flat and level table normally and apply gentle pressure with your hands to make sure the feet are square and the product level. Minor adjustments can also be done by hand manually to each individual foot until satisfied.



Step 6.

Stack the product as you normally would. You will have gained 1 inch at the edges and 1/2 inch at the center. This will significantly increase airflow between two stacked products. This is a simple solution.



feedback form feedback form

by IncognitoOOL
last modified: 2007-09-18 16:37:56

feedback form

feedback form

Any feedback you provide (corrections, updates or suggestions) are sent to the owner of this FAQ
and anyone else involved in writing or editing this item.

by Lanik
last modified: 2005-06-22 00:46:54

feedback form

feedback form

Any feedback you provide (corrections, updates or suggestions) are sent to the owner of this FAQ
and anyone else involved in writing or editing this item.

by ff1324 edited by Lanik
last modified: 2005-06-22 00:45:56

feedback form

feedback form

Any feedback you provide (corrections, updates or suggestions) are sent to the owner of this FAQ
and anyone else involved in writing or editing this item.

by thecrazy edited by Lanik
last modified: 2005-08-12 00:31:02