site Search:


 
    All FAQs Site FAQ DSL FAQ Cable Tech About DSL Distance DSL Hurdles »»






how-to block ads



Search for: in all FAQs
FAQ RevisionsEditors: sashwa See Profile, birdfeedr See Profile, More Fiber See Profile, kadar See Profile
Last modified on 2012-05-23 11:13:01

8.1 Routers

Linksys Setup

Setup Page:
setup screenshot
ALL USERS
ROUTER NAME: Enter what you wish or leave it blank.
DOMAIN: Enter your ISP's domain or leave it blank.
LAN IP ADDRESS: 192.168.1.1 (default router IP do not change) (you will thank me later if your router ever loses its settings)

  PPPoE USERS:
  (x) OBTAIN AN IP ADDRESS AUTOMATICALLY

  PPPoE (x) Enable
  USERNAME: Your Username.
  PASSWORD: Your Password.
  (x) Connect on Demand: Max Idle Time 0 Min.
  (x) Keep Alive.

  STATIC IP USERS:
  (x) Specify an IP Address: Enter your IP address   here.
  SUBNET MASK: Enter your Subnet Mask IP here.
  DEFAULT GATEWAY: Enter Your Gateway IP here.
  DNS 1,2,3: Enter you DNS IPs here.

Status Page:
Status Page:
status screenshot

  PPPoE USERS:
  In this status page you will find very useful   information if you plan on using internal static   IP addresses.

Once you have setup your router, and connected.. you will find on this page the following information that you may want to write down:

IP ADDRESS: This is your current IP Address (very important)
SUBNET MASK: Your current Subnet Mask
DEFAULT GATEWAY: Your Gateway IP. (important for traceroutes)
DNS 1,2,3: Your DNS IPs. (very important)

  Network Settings:
PC network screenshot

ALL USERS
All you need in here to share your connection on each PC is the following:

1) NIC (network interface card) any brand and speed will do
2) TCP/IP (the internet protocol)

You may have NetBEUI for internal file/printer sharing.

  TCP/IP ADDRESS:
pc tcp/ip screenshot

ALL USERS:
My suggestion here is that you setup a Static IP for each of your PCs.

Now I like to use the following range of numbers 192.168.1.101 to 192.168.1.199 .. but you may use what you wish.

  TCP/IP WINS Config:
pc wins screenshot

ALL USERS:
Just make sure that you have WINS Resolution disabled.

  TCP/IP Gateway:
pc gateway screenshot

ALL USERS:
Enter your router's IP address as your gateway.
192.168.1.1

  TCP/IP DNS:
pc dns screenshot

ALL USERS:
***** VERY IMPORTANT *****

Remeber I had you look at your status page of the router for your DSN numbers. This is where you must inter those IP addresses.

If you do not enter the DNS numbers in here you will not be able to browse the net unless you know the IP number for all the sites out there.

ONCE AGAIN >> HERE IS WHERE YOU MUST ENTER YOUR DNS IPS

More info available here:
http://www.linksys.com/tech_helper/intro.html

(temp)

FAQ by kadar


got feedback?
Just installed a linksys WRT54G2 with a verizon Westell 6100F. The 6100F is not accessible via http or telnet, in fact it locks up if you attempt to interface with it. The IP of the 6100F is 192.168.1.1. You can see that not changing the default IP of the Linksys is no longer an option. Other than changing the Linksys IP, I did not make any other changes and I can surf just fine. Jeffrey Highlen

2009-02-21 22:19:41


I also had the listed problem, but was able to change the routers IP to 192.168.2.1 and it solved the problem.

2009-08-31 00:01:42


by edited by kadar See Profile
last modified: 2002-08-26 18:45:32

BA
(PPPoE)
Telnet to router

setup menu 1
with any system name, or blank
domain name has to be your ISP i.e. "bellatlantic.com", "verizon.net",
enter thru and save,

go to menu 2,
use space bar to toggle to ip address attached on LAN,
type ip address of your pc i.e. "192.168.0.2",
enter thru and save.

Go to menu 4,
set Encapsulation to PPPoE,
set login, which could be either "username" or "username@domainname", and password,
leave everything as default, dynamic ip address, sua to yes.
Enter thru and do a test, you should get IPCP opened for last command.

Go to menu 24.1,
check for WAN IP address, if it is showing,
then you can open browser.

GTE
(DHCP)
Telnet to router

setup menu 1
with any system name, or blank
domain name has to be your ISP i.e. "vz.dsl.genuity.net",
enter thru and save,

go to menu 2,
use space bar to toggle to ip address attached on LAN,
type ip address of your pc i.e. "192.168.0.2",
enter thru and save.

Go to menu 4,
set Encapsulation to Ethernet,
login and password are N/A
leave everything as default,
Enter thru and do a test, you should get IPCP opened for last command.

Go to menu 24.1,
check for WAN IP address, if it is showing,
then you can open browser.

(temp)

FAQ by kadar


got feedback?

by edited by kadar See Profile
last modified: 2002-08-26 18:46:03


Thursday, 24-May 15:01:49 Terms of Use & Privacy | feedback | contact | Hosting by nac.net - DSL,Hosting & Co-lo
over 12.5 years online © 1999-2012 dslreports.com.