site Search:


 
    All FAQs Site FAQ DSL FAQ Cable Tech About DSL Distance DSL Hurdles »»






how-to block ads



Search for: in all FAQs
FAQ RevisionsEditors: Doctor Olds See Profile, fourboxers See Profile, sashwa See Profile
Last modified on 2013-03-22 17:24:09
view: single page · printable
Table of Contents

3 Hardware

Yes. It is available below (Requires the FREE Adobe Acrobat Reader):

5100/5200 DSL Modem Quick Start Guide (post-Aug 2002 models)

Alternate link:

5100/5200 DSL Modem Quick Start Guide

got feedback?

by Doctor Olds See Profile
last modified: 2013-01-09 20:43:33

It's available below (four links in case some go dead) Note: Requires the FREE Adobe Acrobat Reader:

SpeedStream 2.1.pdf
5100, 5200, 5400, 5500 User Guide Revision 2.1 [3.3MB PDF file]

Alternate link:
5100, 5200, 5400, 5500 User Guide Revision 2.1 [3.3MB PDF file]

Newer Name version of the User Guide (still revision 2.1)

5x Router UM 007-0820-003.pdf
SpeedStream 5xxx Router User Guide Revision 2.1 [3.3MB PDF file]

Alternate link:
SpeedStream 5xxx Router User Guide Revision 2.1 [3.3MB PDF file]


got feedback?

by Doctor Olds See Profile
last modified: 2013-01-09 17:47:59

At the Efficient KB Article links below: [Requires the FREE Adobe Acrobat Reader]

SpeedStream 4100 Quick Start Guide [977 KB PDF file]

Siemens 4100 Quick Start Guide [913 KB PDF file]

SpeedStream 4200 Quick Start Guide [1.1 MB PDF file]

Siemens 4200 Quick Start Guide [1.1 MB PDF file]

SpeedStream Router User's Guide Models 4100 and 4200 [2.47 MB PDF file]

Siemens Speedstream 4100/4200 Router User Guide [2.5 MB PDF file]

Siemens Speedstream 4100/4200 Data Sheet [164 KB PDF file]


got feedback?

by Doctor Olds See Profile

Check this thread out:

»[Equipment] 1704 Manual

got feedback?

by sashwa See Profile
last modified: 2011-11-13 12:10:27

1. Login to the modem. Put 192.168.254.254 in your browsers address bar.

2. Click on Login on the choices on the left

3. Login with admin as the un/pw

4. Click on Setup > WAN Interface

5. Click on the OE BRG text

6. Select RFC-2684 Bridged then select Finish

7. To allow the changes to take effect click on the CPE select the red reboot link



This method should allow for an external device to handle the PPPoE session (PC, 3rd party router, etc.)


got feedback?

by Windstream See Profile edited by fourboxers See Profile
last modified: 2011-11-28 16:58:01

-Open your web browser and go to »192.168.1.1. (You must be connected to the Linksys on one of its LAN ports and have DHCP enabled so your PC gets an IP from the Linksys subnet for this to work).

-When prompted for a User Name and Password, leave the user name blank and type in the password of admin. Click the OK button.

-Click on the Applications & Gaming tab and ensure Port Range Forward is selected. Fill in the information using the following guidelines:

*Application: Type in the name of what program you are using.
*Start/End: Type in the ports you are needing forwarded. The RED example uses one specific port, whereas the GREEN example uses a port range.
*Protocol: Select TCP, UDP, or Both.
*IP address: Type in the IP address of the computer on your network that will be receiving the port traffic.
*Enable: Enables or disables this port forwarding rule.

When you are finished, click Save Settings. Port forwarding should now be enabled and set up on your Linksys router.

DISCLAIMER: Windstream does not provide any over-the-phone support for port fowarding on the Linksys router. If you have any further questions about port forwarding on your Linksys router, please contact Linksys technical support at 1-800-326-7114, or go to their support forum database at http://forums.linksys.com/. »homecommunity.cisco.com/linksys/···=linksys


got feedback?

by Windstream See Profile edited by Doctor Olds See Profile
last modified: 2012-12-23 21:36:29


Friday, 24-May 18:02:07 Terms of Use & Privacy | feedback | contact | Hosting by nac.net - DSL,Hosting & Co-lo
over 13.5 years online © 1999-2013 dslreports.com.