 | |
|
| ||||
|
|
Home | Reviews | Tools | Forums | FAQs | Find Service | ISP News | Maps | About |
|
how-to block ads |
1.1 DSLR Wake on Lan
Get started here: /wakeup  got feedback?by KeysCapt To resolve just forward the port on the router (Port 32767 if for DSLR) to IP 192.168.0.255, provided it operates in this IP range. Mulicast IPs should be hard coded in the ARP table of the routers. The WOL packet would then be passed to all nodes behind the router but the speficied MAC address would be the one to wake up.
got feedback?Linksyswrtg2 does NOT allow port forwarding to 192.168.0.255.
A quick hack: while in the router port forwarding page disable javascript in the browser, type "255" in the field (which would popup an error while javascript was on), re-enable javascript, hit SAVE. 2009-05-02 12:59:08 by KeysCapt got feedback?by KeysCapt This text assumes the reader will be using a computer (motherboard and BIOS) and NIC (network card) that are compatible with WoL technology and that the hardware is properly set up to do so. Some network cards must be placed into a special PCI slot on the motherboard in order work properly while others must be tethered to the motherboard by a special cable which plugs into a particular place on both the motherboard and the NIC. A general WoL FAQ can be located here. This text was written mainly to indicate how to forward the proper port through a Linksys router in order to utilize WoL technology through the router. In order to use WoL (Wake on LAN, aka: RWU or remote wake up) to wake up a computer from over the Internet the appropriate port needs to be forwarded from the WAN side to the LAN side of the router. Since a computer that is not turned on doesn't have an IP address, the packet sent to wake the computer needs to be forwarded to all computers on the LAN side of the router in order to ensure it gets to the computer it is destined for. This "magic packet," which can be sent using software available from different sources, contains a special string designed to work with WoL as well as the MAC address of the network card in the computer which should wake up. Because the MAC address of the correct machine is included in the packet, only the machine that is supposed to wake up actually will. To set up port forwarding in the router go here (default). The port that needs to be forwarded will vary depending on what software you're using to send the magic packet, but the normal port used for WoL is 9. UDP is the protocol that needs to be forwarded; it is not necessary to forward the TCP protocol. The IP address that the packet needs to be forwarded to will change depending on the network mask you are using on your LAN. The default network mask is 255.255.255.0. If you are using this mask, you should forward traffic destined to your WoL port to xxx.xxx.xxx.255. If you are using the default settings in the router, this address would probably be 192.168.1.255. The 255 in the address, using the default network mask, signifies that the router should forward any information sent to the indicated port to all computers on the LAN side. If you are using the router's default settings with a program that sends the "magic packet" to port 9, basically just forward all UDP traffic on port 9 to 192.168.1.255. If there is an option for external and internal ports, the same port number should be used for both external and internal. WoL tool allows you to wake a computer remotely over the Internet through a browser. On this page they indicate UDP port 9 is what the tool uses, but as of this writing the magic packet is actually sent through UDP port 32767. So, if you're using this tool be sure to forward port 32767 through the router. While it is possible to locate software that will send WoL "magic packets" via a quick search in your favorite search engine, a couple of sites offering such software are: Depicus (also provides info on WoL) AMD (also provides info on WoL) --------- This FAQ entry copied from the LinkSys FAQ and posted there by Gork User svenlange  adds that iptables (many routers are based on this) does not support forwarding to *.255 address - so the only option is direct forwarding to certain IP with permanent ARP entry.See his thread on the subject: /forum/remark,13287946
got feedback?by KeysCapt got feedback?by KeysCapt This depends somewhat on your internal settings and the way your machine is designed to work. It doesn't "wake" because your NIC doesn't accept packets in standby or hibernation mode. (Of course, you must have a suitable NIC with the WOL feature.) You can check by looking at the LEDs on your NIC when the computer is turned off and when it is in "sleep" mode. If they are lit, the computer should wake when the remote packet is received. When the computer is hibernating if the LED isn't on it will not wake. You can explore the settings in the "power" section of a Windows computer Control Panel, but this may not be adjustable.
got feedback?Dear sir/madam,
If been trying to get the WOL working but it doesn't seem to wake up my pc.
What I've done so far:
- enabled WOL in the BIOS and Windows settings of the PC
- on my router I've forwarded the UDP port 9 to the same PC
- on your site I've entered the external IP adres: 87.212.9.--- and the MAC of the PC
I've also checked the LEDs of the NIC.
Please could you help me with this?
Kind regards,
Jeroen Kluft 2010-02-19 02:58:53 by KeysCapt you can run a quick test to see if WOL works for you.Just grab your MAC address and IP and go here: »www.ubilight.com Click on "Wake Up", fill in the required info, and check it out. got feedback?www.ubilight.com Does not work any more 2010-03-11 10:15:32 (SuperNet9 Unfortunately, the "www.ubilight.com" address is no longer in service. It is now an adsite. 2011-06-07 11:46:15 by KeysCapt You can see comments and questions on this service here: /forum/wakeonlan got feedback?by KeysCapt | |||||||||
| Thursday, 24-May 15:55:50 | Terms of Use & Privacy | feedback | contact | Hosting by nac.net - DSL,Hosting & Co-lo over 12.5 years online © 1999-2012 dslreports.com. |
