OS and Software > Microsoft Help > [XP Pro] Frequent BSODs in Win XP Pro SP2, please help

reply to stilz2

Re: [XP Pro] Frequent BSODs in Win XP Pro SP2, please help

Re: [XP Pro] Frequent BSODs in Win XP Pro SP2, ple

Mini02090501.zip 15,238 bytes (Mini02090501.dmp)	Mini02090502.zip 17,920 bytes (Mini02090502.dmp)	Mini02090503.zip 13,370 bytes (Mini02090503.dmp)
Mini02090504.zip 16,371 bytes (Mini02090504.dmp)

Ok....A few other questions. Have you gone through the BIOS and made sure everything is at default? Make sure you do not have memory at aggressive timings. Also, on the reinstall did you stop after the XP, SP2 and motherboard drivers and see if it was stable before anything else was loaded? That would rule out a driver issue. Are all of your PS voltages stable and near the true voltage on the +5, +12 and +3.3? I have also had a floppy that went bad and was pulling the 12v down and making the computer very unstable. Hope these items help. I really can't see anything in the mini dumps that point to one particular thing.

I made sure in BIOS nothing is OC'ed, and even reset it with jumper. I installed the stuff I normally use after the clean install, e.g. Firefox, Thunderbird, Daemon tools, Nero, and a few others, so I don't really know.
How do you check the voltages stuff you are talking about? Look at the health status in either the BIOS or via software like Speedfan or MBM5? What should I check for?
I'm now testing my system with a new mobo, I'll report back.

After changing the mobo, my system stopped getting BSODs...for a while. What happens instead is that, sometimes the screen would just freeze, though I can still move the cursor around. Then the screen would turn black, then on again and everything back to normal. This happens about once an hour or so. While this is a bit annoying, at least I'm not getting BSODs. Alas, it did not last; I just got the first BSOD after changing the mobo. Could you guys tell me how to view the minidump files? Thank you.
Btw, my new mobo is a cheap PC Chip M811LU.

Here's a link on reading minidump files:

»support.microsoft.com/kb/315263/EN-US/

You can use WinDbg of the Debugging Tools for Windows to read Minidump files:

Here's a link, on setting up WinDbg, with screen shots:

»forum.lowyat.net/lofiversion/ind···632.html

Also, check the Event Viewer logs for clues to what is wrong (Start > Run > eventvwr).

Did you do a "repair" installation of XP, after switching motherboards?

Since one your errors is a KERNEL_MODE_EXCEPTION_NOT_HANDLED_M probably caused by nv4_disp.dll, try what is suggested in the following MS KB article:

»support.microsoft.com/Default.as···&sd=RMVP

Try using the 56.72 drivers that have proved very stable for many users.

As suggested, after uninstalling the old drivers, install the new drivers in Safe Mode.

If you haven't already, update your VIA 4in1 drivers to the latest version.

Also, since you switched MB's, consider performing at least a "repair" install of XP. This will allow for a re-evaluation of hardware.

reply to stilz2
Have you tried ALL the versions of nVidia drivers available for your card? I had infinite loop BSODs from the moment I got this Dell Nov 2003 with an nVidia card. I updated right away to what was the latest drivers at the time and that didn't help. The next several driver upgrades didn't help. Finally, the last two upgrades (61.77 and 66.93) have been good. No more infinite loop problems. It is ironic though because the card is old enough that the earlier drivers give better performance but I can't use them.
--
The first and foremost function of our jurors is to protect private citizens from a tyrannical and intrusive government...Jurors are the last line of defense for liberty. Thomas Jefferson 1789

Still a no go. I've tried the 56.7 and 66.93 drives, removed in safe mode, reboot, cleaned with Driver Cleaner Pro, installed in safe mode, problems persist. I've also installed the VIA 4in1 latest driver.
Could you elaborate on the "repair" install? What I did is boot with the XP cd and get into repair mode, and I have no idea what to do in the command line mode.
Thanks.

BTW, I'm close to wanting to do a reinstall again, but the thing is I'll have to call to activate if I do a reinstall. Is there a way to store the activation record somewhere and port it into the next one?

I've just tried a new installation of Win XP and still having the same problem. Then I tried a different video card, and same stuff happens. This just doesn't make any sense at all. I've pretty much replaced everything in my computer except the case.
Could you guys suggest other versions of driver to try out? I'm now thinking maybe it's the motherboard simply doesn't like the driver or something.
BTW, could someone point out where the 'edit' button is? Thanks.

You can edit a post up to 12 hours after posting, after that the edit button is gone:

»Site FAQ »Can't edit your post?

After your new installation of XP, when did you start getting the BSOD's again? Was it after you installed all your third party programs?