Re: [BroadVoice] provisioning unlocked PAP2 in VOIP Tech Chat http://www.dslreports.com/forum/r14553994 en Sat, 28 Nov 2009 16:47:14 EDT Sat, 28 Nov 2009 16:47:14 EDT time zone; local time http://www.dslreports.com/forum/remark,14589699 david_gruenb : The PAP2 shows the correct local time on the info page, but voice mail is off by three hours, meaning when I call myself from my cell phone and leave a message and retrieve it, at 7am, for example, the voice mail says it was left at 10am. Obviously, some setting is 3 hours later than where its is supposed to be, but the question is where or what is that setting. Thanks.]]> http://www.dslreports.com/forum/remark,14589699 Sun, 16 Oct 2005 10:47:39 EDT Re: [BroadVoice] How to set up unlocked PAP2 for B http://www.dslreports.com/forum/remark,14561131 david_gruenb : I started a new thread re my *86 issue. »*86 not working

Thanks for the help.]]> http://www.dslreports.com/forum/remark,14561131 Wed, 12 Oct 2005 12:48:11 EDT Re: [BroadVoice] working unlocked PAP2 http://www.dslreports.com/forum/remark,14560730 david_gruenb : Its working now by trial and error and a mishmash of suggested settings. Kind of hard to say exactly what was the problem. I put it in the DMZ, forwarded ports. Then I ran the voxilla.com wizard again, but It was only when I noticed that the wizard give me a west coast proxy but Broadvoice give me an east cost proxy that I noticed an inconsistency (proxy-dca.broadvoice.com v. proxy-lax.broadvoice.com). The wizard turns on the DNS servicer but when I turned it off it worked.

[edit] actually one thing is not working, voicemail pickup from the phone. When I dial *86, nothing happens. I notice a voicemail server entry box in the pap2. Do I need to set that up?

Thanks for all the suggestions.]]> http://www.dslreports.com/forum/remark,14560730 Wed, 12 Oct 2005 11:50:09 EDT Re: [BroadVoice] provisioning unlocked PAP2 http://www.dslreports.com/forum/remark,14560489 mazilo : How hard is it for you to check your NAT/Firewall router features, i.e. uPnP? If it is simple, then it will save you lots of hassle to locate the uPnP features to have them enabled. If you have a non-symmetrical NAT/Firewall router, then enable the STUN server and disable the Outbound Proxy server on your VoIP devices; otherwise, do the other way around.]]> http://www.dslreports.com/forum/remark,14560489 Wed, 12 Oct 2005 11:16:43 EDT Re: [BroadVoice] provisioning unlocked PAP2 http://www.dslreports.com/forum/remark,14560008 david_gruenb : Still not working. Any chance the firewall instructions above need tweaking??]]> http://www.dslreports.com/forum/remark,14560008 Wed, 12 Oct 2005 09:58:50 EDT Re: [BroadVoice] provisioning unlocked PAP2 http://www.dslreports.com/forum/remark,14558413 im_chandave : Sorry, wasn't very clear.

In the "User ID" of the PAP2, use the construct created by the concatenation of:

phone_number@registrar_ip

where phone_number is the phone_number entry from the Generic SIP details from BV and registrar_ip is the registrar_ip entry also from the Generic SIP details from BV.

Using your example from your Generic SIP details dump from BV, try using:

323xxxxxxx@sip.broadvoice.com

For the Line 1 > Subscriber Information > User ID.

See ya...

d.c.]]> http://www.dslreports.com/forum/remark,14558413 Wed, 12 Oct 2005 00:57:41 EDT Re: [BroadVoice] provisioning unlocked PAP2 http://www.dslreports.com/forum/remark,14558231 david_gruenb : d.c., by "BV_phone_number@BV_registrar_ip" do you mean literally "BV_phone_number@BV_registrar_ip" or do you mean xxxxxxxxxx@BV_registrar_ip with xxxxxxxxxx representing my phone number?]]> http://www.dslreports.com/forum/remark,14558231 Wed, 12 Oct 2005 00:26:02 EDT Re: [BroadVoice] provisioning unlocked PAP2 http://www.dslreports.com/forum/remark,14554426 im_chandave : A message from mberlant over on voxilla gave me some ideas.

    •Please change the Line 1 > Subscriber Information > User ID to BV_phone_number@BV_registrar_ip.

If that doesn't work then try leaving the User ID as BV_phone_number@BV_registrar_ip and changing the Line 1 > Proxy and Registration > Proxy to the same value as BV's proxy_ip.

Also, make sure you power-cycle the PAP2 after all these changes. Sometimes the configurations don't take effect immediately. The power-cycle will ensure that it re-reads the flash memory for all the settings.

See ya...

d.c.]]> http://www.dslreports.com/forum/remark,14554426 Tue, 11 Oct 2005 15:50:17 EDT Re: [BroadVoice] provisioning unlocked PAP2 http://www.dslreports.com/forum/remark,14554226 im_chandave : Time to start up a syslogd and turn on debugging on the PAP2.

I would love to help on this but I'm still waiting for my PAP2's to arrive (sometime in November). Until then, I'm willing to help look over the SIP communication that will be captured by the PAP2's syslogging.

See ya...

d.c.]]> http://www.dslreports.com/forum/remark,14554226 Tue, 11 Oct 2005 15:21:56 EDT Re: [BroadVoice] provisioning unlocked PAP2 http://www.dslreports.com/forum/remark,14554025 david_gruenb : I am set to no/no, but its not working. Any troubleshooting tips?]]> http://www.dslreports.com/forum/remark,14554025 Tue, 11 Oct 2005 14:50:27 EDT Re: [BroadVoice] provisioning unlocked PAP2 http://www.dslreports.com/forum/remark,14553994 CommSoft8086 : Also, don't forget to set the DNS Server Order in the 'System' tab to manual, DHCP, and double check the DNS server entries to match the primary and secondary provided by BV (or the proxy-dca... address won't resolve).]]> http://www.dslreports.com/forum/remark,14553994 Tue, 11 Oct 2005 14:45:40 EDT Re: [BroadVoice] provisioning unlocked PAP2 http://www.dslreports.com/forum/remark,14553879 im_chandave : Make Call Without Reg: no
This will disable dialtone if your PAP2 cannot register with BV.

Ans Call Without Reg: no
This ensures that calls can only come into your PAP2 if you are registered with BV.

These two settings will determine if you want your PAP2 to make outbound calls or receive inbound calls when your connection to BV is down.

See ya...

d.c. ]]> http://www.dslreports.com/forum/remark,14553879 Tue, 11 Oct 2005 14:24:56 EDT Re: [BroadVoice] provisioning unlocked PAP2 http://www.dslreports.com/forum/remark,14553812 sa2004 :
said by david_gruenb See Profile :

Make Call Without Reg: yes/no
Ans Call Without Reg: yes/no

I am going to assume the answer should be "yes" to both, but if not I will try "no".
The answer to both should be "no".]]> http://www.dslreports.com/forum/remark,14553812 Tue, 11 Oct 2005 14:16:28 EDT Re: [BroadVoice] provisioning unlocked PAP2 http://www.dslreports.com/forum/remark,14553766 david_gruenb : Well that is really great. It tracks perfectly, with one exception. At number 18, it says "The PAP2's ... Register should all be set to "yes". There is no "Register" entry. There are two entries as follows:

Make Call Without Reg: yes/no
Ans Call Without Reg: yes/no

I am going to assume the answer should be "yes" to both, but if not I will try "no".

Unfortunatly, it is not working. "Registration State: Can't connect to login server."

I don't see an entry for dial plan. I have *xx|#xx|[3469]11|0|00|[2-9]xxxxxx|1xxx[2-9]xxxxxxS0|xxxxxxxxxxxx.]]> http://www.dslreports.com/forum/remark,14553766 Tue, 11 Oct 2005 14:07:17 EDT Re: [BroadVoice] provisioning unlocked PAP2 http://www.dslreports.com/forum/remark,14553408 im_chandave : Yes. Switch to Generic SIP and get your credentials. Here are the steps to use the BV credentials obtained via the "Generic SIP" to configure your Linksys PAP2 (I assume the entries are similar to the SPA-2K entries):

    •Using your web browser, goto »https://www.broadvoice.com/AccountPortal/
    •Login with your BV web portal account name and pasword
    •Select the ACCOUNT tab.
    •Click the Edit button on the My Devices panel.
    •In the Current Device selection box you probably have Linksys PAP2-NA. Leave that alone.
    •In the Replace With selection box, you should be able to select Not Listed (Generic SIP). Choose that one.
    •Enter your portal account password in the Portal Password
    •Click the Update button
    •Now go back to the ACCOUNT tab and click the Show Settings in the My Devices panel.
    •In a web browser, access the admin/advanced pages of the PAP2.
    •The primary_dns_ip entry should be used in the PAP2's System > Optional Network Configuration > Primary DNS
    •The secondary_dns_ip entry should be used in the PAP2's System > Optional Network Configuration > Secondary DNS
    •The proxy_ip entry should be used in the PAP2's Line 1 > Proxy and Registration > Outbound Proxy
    •The proxy_port is not needed since BV uses the standard SIP UDP port.
    •The registrar_ip entry should be used in the PAP2's Line 1 > Proxy and Registration > Proxy.
    •The registrar_port is not needed since BV uses the standard SIP UDP port.
    •The PAP2's Use DNS SRV should be set to "no".
    •The PAP2's Use Outbound Proxy, Use OB Proxy In Dialog, and Register should all be set to "yes".
    •The phone_number entry should be used in the PAP2's Line 1 > Subscriber Information > User ID.
    •The auth_id entry should be used in the PAP2's Line 1 > Subscriber Information > Auth ID.
    •On the PAP2's Line 1 > Subscriber Information > Use Auth ID, set it to "yes".
    •The auth_password entry should be used in the PAP2's Line 1 > Subscriber Information > Password.
    •The tftp_ip entry can be ignored.
    •The ntp_ip entry should be used in the PAP2's System > Optional Network Configuration > Primary NTP Server
    •The DTMF entry inidicates that the PAP2's Line 1 > Audio Configuration > DTMF Tx Method should be set to Inband+INFO.
    •On the PAP2's Line 1 > Audio Configuration > Preferred Codec, set it to G711u.
    •Set "no" for all the other G7xx Enable entries on the PAP2.
    •On the PAP2's Line 1 > Audio Configuration > Use Pref Codec Only, set it to "yes".
    •On the PAP2's Line 1 > Audio Configuration > Symmetric RTP, set it to "yes".

If your PAP2 is behind a NAT'ing firewall/router, you will need STUN support enabled:

    •In a web browser, access the admin/advanced webpages of the PAP2.
    •In SIP > NAT Support Parameters, set the following to "yes"--Handle VIA received, Handle VIA rport, Insert VIA received, Insert VIA rport, Substitute VIA Addr, Send Resp To Src Port, STUN Enable, STUN Test Enable.
    •Set SIP > NAT Support Parameters > STUN Server to any of the Public STUN servers listed at »www.voip-info.org/tiki-index.php?page=STUN .
    •Set SIP > NAT Support Parameters > NAT Keep Alive Intvl to 15 seconds for now. You can slowly increase that number when you know everything is working correctly.
    •Set Line 1 > NAT Settings > NAT Mapping Enable and Line 1 > NAT Settings > NAT Keep Alive Enable to "yes".
    •Set Line 1 > NAT Settings > NAT Keep Alive Msg to "$NOTIFY" and Line 1 > NAT Settings > NAT Keep Alive Dest to "$PROXY".


Once again, I'm basing all my suggestion on an SPA-2K. I won't get my PAP2's delivered to me until November.

See ya...

d.c.]]> http://www.dslreports.com/forum/remark,14553408 Tue, 11 Oct 2005 13:10:00 EDT Re: [BroadVoice] provisioning unlocked PAP2 http://www.dslreports.com/forum/remark,14552838 david_gruenb : Thanks, Hot Salami, I clicked on "Edit" then changed my current devise from a PAP2 to "Not Listed" (Generic SIP)". Now the settings are listed as follows:

primary_dns_ip: 147.135.0.6
secondary_dns_ip: 147.135.8.6
proxy_ip: proxy-dca.broadvoice.com
proxy_port: 5060
registrar_ip: sip.broadvoice.com
registrar_port: 5060
phone_number: 323xxx-xxxx
auth_id: 323xxx-xxxx
auth_password: xxxxxx
tftp_ip: config.broadvoice.com
ntp_ip: ntp.nasa.gov
DTMF: InBand
registration_time_out: 10_seconds
voice_mail_key: *86
time_zone: GMT-08:00

I filled in the fields that I could find, but was confused by the following:

Broadvoice lists "proxy_ip" and "registrar_ip" but I cant find these. I assume "proxy_ip" is the same as "Proxy on the Line 1 tab, but I cant find "registrar_ip" The PAP2 has "outbound proxy", but I don't see a listing for that from Broadvoice.

I don't see a place in the PAP2 for "tftp_ip: or "ntp_ip:"

I can't connect. The Registration State is "Can't connect to login server"

I hope someone is willing to post screen shots of their PAP2 pages configured for Broadvoice, then I cold just copy the fields. Thanks.]]> http://www.dslreports.com/forum/remark,14552838 Tue, 11 Oct 2005 11:46:36 EDT Re: [BroadVoice] How to set up unlocked PAP2 for Broadvoice http://www.dslreports.com/forum/remark,14551798 CommSoft8086 : *** Leave auto-provisioning off ***

Go to the Broadvoice portal and select the 'Account' tab. Then, select 'show settings' under 'My Devices' -- which will give you your provisioning information. Enter the information into the 'Line 1' tab of the PAP2.]]> http://www.dslreports.com/forum/remark,14551798 Tue, 11 Oct 2005 07:58:27 EDT [BroadVoice] How to set up unlocked PAP2 for Broadvoice http://www.dslreports.com/forum/remark,14551400 david_gruenb : I am new to VoIP, but not networking. I unlocked my a new PAP2 a few days ago and signed up with Broadvoice. I have been instructed to avoid using Broadvoice's auto-provisiong .cfg file because it may relock the PAP2 and to configure it as if it was a generic SIP adapter. I have a very general idea what this all means.

So far Broadvoice has not provided this info via email and I can't find it on the internet. I tried the wizard at »voxilla.com/pap2config.php, and it provided what may be useful data, but I am not getting a dial tone. Perhaps a setting on another configuration setting is messed up as a result of the unlocking process.

Can anyone provide detailed step by step all-inclusive instructions for setting this up, from start to finish, not just the "Line 1" page, but any other pages of the PAP2 configuration that need to be changed from the unlocked state, like the "System" page, including the DNS settings.

Thanks.]]> http://www.dslreports.com/forum/remark,14551400 Tue, 11 Oct 2005 04:00:16 EDT