http://www.dslreports.com/forum/r15213069 en Wed, 09 Dec 2009 04:47:37 EDT Wed, 09 Dec 2009 04:47:37 EDT http://www.dslreports.com/forum/remark,15228145 dslpartner : Get a new modem :)]]> http://www.dslreports.com/forum/remark,15228145 Thu, 12 Jan 2006 10:15:08 EDT http://www.dslreports.com/forum/remark,15227838 sckramer : I put a switch between the two and it did fix it...

do you think I should bug zyxel about this, or at least let them know? do any zyxel techs check this board?

I'll prob just hastle rr for a new modem, thanks!!]]> http://www.dslreports.com/forum/remark,15227838 Thu, 12 Jan 2006 09:08:17 EDT http://www.dslreports.com/forum/remark,15227120 dslpartner : Then that seems to be your problem :| If you cant configure the x-550 to be in 10Mbit half duplex support you might have some luck with a hub that can support 10Mbit half duplex and what the x-550 support, inserted between the two devices.
--
"Perl is executable line noise, Python is executable pseudo-code." ]]> http://www.dslreports.com/forum/remark,15227120 Thu, 12 Jan 2006 03:16:38 EDT http://www.dslreports.com/forum/remark,15224004 sckramer : looked up the modem:

its a toshiba pcx2200... the specs list the port as: 10baseT; half-duplex]]> http://www.dslreports.com/forum/remark,15224004 Wed, 11 Jan 2006 19:02:17 EDT http://www.dslreports.com/forum/remark,15223752 sckramer : haven't contacted zyxel yet... i'm gonna try to narrow it down a little more -- thanks!!]]> http://www.dslreports.com/forum/remark,15223752 Wed, 11 Jan 2006 18:25:30 EDT http://www.dslreports.com/forum/remark,15223722 sckramer : great idea tho, maybe i should try putting a basic 100 mbit switch between the cable modem and x550 wan port as a test, maybe that will convert it correctly?]]> http://www.dslreports.com/forum/remark,15223722 Wed, 11 Jan 2006 18:22:22 EDT http://www.dslreports.com/forum/remark,15223678 sckramer : it acts identically in either auto or 10-mbit

100-mbit it never gets an ip address from the isp]]> http://www.dslreports.com/forum/remark,15223678 Wed, 11 Jan 2006 18:17:01 EDT http://www.dslreports.com/forum/remark,15220602 dslpartner : Could be an issue where the LAN port is 10Mb half duplex only, what happens if you set it to auto?
--
"Perl is executable line noise, Python is executable pseudo-code." ]]> http://www.dslreports.com/forum/remark,15220602 Wed, 11 Jan 2006 10:57:43 EDT http://www.dslreports.com/forum/remark,15220360 sckramer : In the x550 I set it to 10, 100 and auto

it does not work at all at 100, so it must be 10]]> http://www.dslreports.com/forum/remark,15220360 Wed, 11 Jan 2006 10:19:27 EDT http://www.dslreports.com/forum/remark,15220230 dslpartner : What is the speed on the WAN port of the ZyXEL device and what is the speed on the LAN port of the cable modem?
--
"Perl is executable line noise, Python is executable pseudo-code." ]]> http://www.dslreports.com/forum/remark,15220230 Wed, 11 Jan 2006 09:57:08 EDT http://www.dslreports.com/forum/remark,15220186 jp : Not on RR sckramer but on cable modem (sb5100 w/ Cox). Have QoS on auto, firewall on, no entries in the basic setup and let it pull DNS and other info from the modem. MTU is at the default of 1500.

Use both the wired and wireless aspects of the modem and have not noticed any stalls or other issues. Have you called ZyXEL support to see if they can help you?

Hope you can figure it out.
--
All that is gold does not glitter]]> http://www.dslreports.com/forum/remark,15220186 Wed, 11 Jan 2006 09:51:09 EDT http://www.dslreports.com/forum/remark,15220015 sckramer : Hmmm...

I tried every possible combination of settings on this router, (diff MTU settings, turn off QOS, etc, no change) even tried the 1.0 firmware, no change-- I can't get the router section to work without the stalls! the wireless and wired act the same...

I hooked up a usr8200 as the router & using the x550 as a wap for now

any ideas? anyone else using it on a cable modem & roadrunner?]]> http://www.dslreports.com/forum/remark,15220015 Wed, 11 Jan 2006 09:16:33 EDT http://www.dslreports.com/forum/remark,15213069 sckramer : Hello,

I just installed a x550 to replace an older router, the mtu of the old router was always 1500

by default the x550 is 1500, but I'm getting mtu like problems, stalled dl'ds that resume after 30+secs, some web sites acting weird or not loading...

anyone run into this? its a cable modem (rr)

thanks!!]]> http://www.dslreports.com/forum/remark,15213069 Tue, 10 Jan 2006 12:06:04 EDT