| reply to soportec
Re: help with mikrotik right at this moment i am trying to get the router to act as a AP . I have several options and i am putting (bridge and AP Bridge) have also tried all the other ones and I can not get this to transmit at all.. If i do a frequency scan or somthing the Radio sees frecuency usage and the ssid of other networks. Is there somthing special I have to do to get it to transmit.. I had gotton it to transmit a week ago changing the settings around but then i reset all the settings and i cant seem to figure it out again.
thanks in advance
--
dw7700 1.8 G11 IA300, dw4020 satmex5/1230 1.2 Buisness, dw7000 .74 satmex5 .74 pro |
|
| i am about to pull my hair out trying to figure this out . why wont it transmit a signal . it did in my office but here at the site i cant get it to transmit at all. any ideas guys.. bad sr2? rb532? Only 1 blue light is on on the board.
--
dw7700 1.8 G11 IA300, dw4020 satmex5/1230 1.2 Buisness, dw7000 .74 satmex5 .74 pro |
|
|
|
 IntraLinkPremium,MVM
join:2002-08-14
Utah Valley | For AP you should be on AP Bridge.
Check your data rates and enable all of them for now.
On Advanced under Antenna Mode try switching from antenna a to antenna b (some cards have dual ports, but SR2 should be on antenna a I think...)
Preamble Both, frequency power on default, chech you channels etc. |
|
| reply to soportec
MikroTik Forum might be a better place to pose your questions:
»forum.mikrotik.com/
Though, for best results you might want to post your configuration (so others can see what settings you have).
Also, You might find some answers here: “Wireless Client and Wireless Access Point Manual”
»www.mikrotik.com/testdocs/ros/2.···less.php
For example this question quote:
how do i make all clients private from one another.
is answered with this setting:
default-forwarding (yes | no; default: yes) - to use data forwarding by default or not. If set to 'no', the registered clients will not be able to communicate with each other. |
|
| reply to IntraLink
i have it on AP bridge , all data rates are selected, tried from a to b , pramble is both, power is on default, tried almost all channels.. any other thing to check? it can see signal but it dont send any. when i look at the interfaces i see that lan1 is (R) running and wlan1 is active but there is no (R) lan2 and lan3 are disabled.
--
dw7700 1.8 G11 IA300, dw4020 satmex5/1230 1.2 Buisness, dw7000 .74 satmex5 .74 pro |
|
IntraLinkPremium,MVM
join:2002-08-14
Utah Valley | Well, maybe your wireless is running, but you don't have your LAN set up right?
The wireless will not show R until a client is associated.
For AP Bridge to forward packets you either have to route or Bridge that interface with an ethernet interface. |
|
 vipermCarpe DiemPremium
join:2002-07-09
Winchester, CA
1 edit | reply to IntraLink
Its ant B if your using MMXC connector
When you say it is not "transmitting" are you saying with a laptop right next to the system you dont pick up your SSID? or are you saying you see the SSID but you get no traffic to pass anywhere?
Make sure you create a bridge and assign an IP to it then put both WLAN and Ether 1 in that bridge group and it should work as a genreric bridged AP for testing. ONce you are done testing then you will need to make it a routed setup do do everything else correctly. |
|
| reply to soportec
Flags: X - disabled, R - running
0 name="ISP" mtu=1500 mac-address=00:15:6D:53:94:77 arp=proxy-arp
disable-running-check=no interface-type=Atheros AR5213
radio-name="00156D539477" mode=ap-bridge ssid="SonagueraNet" area=""
frequency-mode=regulatory-domain country=united states antenna-gain=15
frequency=2442 band=2.4ghz-b scan-list=default rate-set=default
supported-rates-b=1Mbps,2Mbps,5.5Mbps,11Mbps
supported-rates-a/g=6Mbps,9Mbps,12Mbps,18Mbps,24Mbps,36Mbps,48Mbps,
54Mbps
basic-rates-b=1Mbps basic-rates-a/g=6Mbps max-station-count=2007
ack-timeout=dynamic tx-power-mode=default noise-floor-threshold=default
periodic-calibration=default burst-time=disabled
dfs-mode=no-radar-detect antenna-mode=ant-a wds-mode=dynamic
wds-default-bridge=none wds-ignore-ssid=no
update-stats-interval=disabled default-authentication=yes
default-forwarding=yes default-ap-tx-limit=0 default-client-tx-limit=0
hide-ssid=no security-profile=device4 disconnect-timeout=3s
on-fail-retry-time=100ms preamble-mode=both compression=no
allow-sharedkey=no
--
dw7700 1.8 G11 IA300, dw4020 satmex5/1230 1.2 Buisness, dw7000 .74 satmex5 .74 pro |
|
| with a laptop right next to ap with a 8 dbi omni connected i see nothing ,, not even with net stumbler..
--
dw7700 1.8 G11 IA300, dw4020 satmex5/1230 1.2 Buisness, dw7000 .74 satmex5 .74 pro |
|
1 edit | Another good tool is MikroTik wireless debug logging:
»wiki.mikrotik.com/wiki/Wireless_Debug_Logs
But, if you're not seeing your AP at all... I wonder about your bridge or masquerade configuration |
|
| Flags: X - disabled, I - inactive, D - dynamic
# INTERFACE BRIDGE PRIORITY PATH-COST
0 I wlan1 bridge1 0x80 10
1 ether1 bridge1 0x80 10
above is my bridge setting but it shows the wlan1 INACTIVE Why?
--
dw7700 1.8 G11 IA300, dw4020 satmex5/1230 1.2 Buisness, dw7000 .74 satmex5 .74 pro |
|
| ok status.. i am using a toshiba A105-S4094 and i can not see the wireless signal my partner has a Dell 640M with VISTA and he can see the signal with his laptop. We have another laptop same as mine with xp pro and it cant see it either. What could this be? I have changed the mode , channel and nothing.. not even with my net stumbler.
my partner gets a ip from the router going to the mikrotik and is able to browse internet. (have bridge set up on router)
--
dw7700 1.8 G11 IA300, dw4020 satmex5/1230 1.2 Buisness, dw7000 .74 satmex5 .74 pro |
|
| other note , i had to change the antenna to B instead of A |
|
| one other question , what package should be installed on the router . wireless or wireless legacy? i i try to put both on it disables one or the other
--
dw7700 1.8 G11 IA300, dw4020 satmex5/1230 1.2 Buisness, dw7000 .74 satmex5 .74 pro |
|
