spacemanspiff192
@comcast.net
| config spa2102 to work on viatalk
has anyone found step by step instructions for setting up the linksys gizmo to work on viatalk byod plan. I have unlocked the gizmo and have received an email from vt but I cannot locate any instructions and I don't want to screw anything up and have to wait for a new adapter to arrive. Thank you in advance for your help. |
|
hallobob5674245
@comcast.net | I have the same question. Any help would be great. |
|
DaEnigma
join:2004-11-26
Las Vegas, NV
2 edits | Keep in mind your VT server may be different (I am in Oregon) and the dialplan will prob need to be tweaked since it was the SR dialplan... |
|
sunny_again
@qwest.net
|  reply to spacemanspiff192
SUCCESS configuring a Sunrocket SPA2102-R to new ViaTalk service!!!
I am not a BYOD customer, but I thought I would try to configure my old Sunrocket SPA2102-R while waiting for my new VT adapter to arrive.
Here is a summary of the changes I made:
First I had to unlock the Sunrocket Gizmo. I followed the instructions at: »gizmopasswords.blogspot.com/2007···2-r.html.
Here's a quick summary of the instructions on that page:
Pick up your phone and dial:
**** (it will ask you for option#)
723646# (when asked for option)
78778839# (when asked for password)
1# (when asked for value)
1 (when asked to save)
--
If your Gizmo is behind your router, don't hang up. You will need to enable access from WAN side.
7932# (this is the option#)
1 (to save)
--
If you don't know the IP address of your SPA2102, use option 110# to hear it.
--
Do NOT do a factory reset. This seem to create problems where the password gets set to an unknown password. Just don't do it!
If you followed the instructions above, you should now be able to access the web administration for the SPA2102-R. On my network the URL is 192.168.1.66. Chances are that yours is different. You can access the admin using this address (you must of course enter your own ip): »192.168.1.66/admin/voice/advanced
If you are able to access the configuration of the Gizmo, you just need to obtain the right values from ViaTalk to be used when configuring the Gizmo.
Go to your ViaTalk account management and from the Main Menu (Control Panel) click the Softphone Config icon on the last row of icons. Select software Xten and click Get Configuration.
You should now see a list of values. You will need these values as you follow the steps below to change your SPA2102 configuration.
My SPA2102 is at Software Version 3.3.5(a). I did not try to upgrade the firmware since others have had problems. Instead I decided to just try the same firmware and it worked out.
These are the settings I changed:
VOICE tab:
System tab:
Restricted Access Domains: I removed all entries
Provisioning tab:
Enable: NO
Line 1 tab:
Proxy and Registration section:
Proxy: ViaTalk Config value for "SIP proxy"
Outbound Proxy: ViaTalk Config value for "Outbound Proxy"
Subscriber Information section:
Display Name: ViaTalk Config value for "Display Name"
User ID: ViaTalk Config value for "Username"
Password: ViaTalk Config value for "Password"
Auth ID: ViaTalk Config value for "Authorization" - and make sure "Use Auth ID" is set to YES
ROUTER tab:
Optional Settings section:
Domain: ViaTalk Config value for "Domain"
Primary DNS: 64.118.82.166
Secondary DNS: 216.120.225.19
DNS Server Order: Manual
DNS Query Mode: Parallell
Primary NTP Server: ViaTalk Config value for "Domain"
Secondary NTP Server: ViaTalk Config value for "Domain"
I don't know whether all these settings were necessary or not, but after making these setting, I turned off my modem, my router and the SPA2102 for 2 minutes. I then powered up my modem and router, then waiting another 2 minutes before powering the SPA2102. After this, my new ViaTalk phone number is functional.
I configured my Sunrocket phone number to forward to my ViaTalk number, so at this point I am able to receive calls coming in on my Sunrocket number.
Next step is to process the phone number transfer.
Good Luck! |
|
sunny_again
@qwest.net | Forgot to mention that when you access the Gizmo configuration, the user/password is:
User: admin
Password:7UprUtew |
|
