elvisk
join:2003-08-17
Boston, MA
| Pap2v2 - trixbox CID and one other problem
Hello guys,
I had given up on the Pap2v2 as a useful device and hadn't looked at these thread in a while. I have to say great job on figuring out the tricks to get it to register to asterisk. Thanks for all the hard work!
Now that it's registered (both lines) and mostly working I wanted see if there's a fix for couple of problems.
1. CID is not working reliably. About 50% of time it says "incomplete data." Are there settings that I can play with?
2. When I answer a call it seems to make a slight buzzing sound for about a second or two and during the buzz, no one can hear me and I can't hear the other party. Any idea?
Thanks in advance.
Elvisk |
|
tommy13v
Premium
join:2002-02-15
Glenville NY | Change the ring voltage on the adapter. It's possible that the phone requires more power for the CID issue. I had a GE cordless set with this issue a while back. |
|
arsh
join:2007-03-06
L'Ile-Bizard, QC
| reply to elvisk
Hi Elvisk,
I am also in a similar situation, my pap2v2 registers to trixbox for about 4 hours and then goes off line. I have to power cycle the pap2v2 to make it register again, would you please share your settings for trixbox and pap2v2 to make it work.
Thanks |
|
pbxdude29
@comcast.net
| Well, the noise that you are experiencing may be on the Asterisk machine that you are running, i have seen this problem and it was the IRQ hard drive issue. You get a very sharp and noisy sound on the phone.
Is the pap2v2 a remote extension or a local extension?
The settings should be quit simple.
Thanks
Ben
www.click4pbx.com |
|
elvisk
join:2003-08-17
Boston, MA
| pbxdude29,
It's a local extension and the noise/CID issues did not exist with a Pap2 version 1. Since this issue was not there with the older pap2, I suspect that it's not an IRQ issue. Any other ideas? Could it be a ring voltage issue?
tommy13v,
What are the proper settings for the ring voltage for the Pap2v2? Can I just change the values in these fields and send them via xml? Can I just use 90 like the version 1?
Thanks.
Elvisk |
|
elvisk
join:2003-08-17
Boston, MA
| reply to arsh
arsh,
1.00.22 FW
the trick was to register line 1 to the asterisk box using the ip address and line 2 via a different dns address.
Also use the following from this thread
»[General] The new PAP2 v2.0
context=default
host=dynamic
type=friend
mailbox=99
callerid="House Line 1"
username=91
secret=1234
rfc2833compensate = yes
nat=route
dtmfmode=rfc2833
insecure=port,invite
good luck |
|
arsh
join:2007-03-06
L'Ile-Bizard, QC
| Elvisk,
Thanks for the reply, I already tried these settings beside the "rfc2833compensate=yes" because I have read on this forum that this parameter is only supported on asterisk 1.4 not in asterisk 1.2. I am also running the firmware version:1.00.13 on the pap2v2, do I have to upgrade to ver:1.00.22 to make this work.I will try these settings anyway. Thanks.
arsh |
|
mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| said by arsh  :..., do I have to upgrade to ver:1.00.22 to make this work. Beware that no CYT Unlocker is able to unlock a PAP2v2 wth firmware v1.00.22. |
|
arsh
join:2007-03-06
L'Ile-Bizard, QC
| mazilo,
Thanks for the heads up, the unit is unlocked at 1.00.13 and I do have the encryption key for that. I want to make this unit work with my trixbox 1.2.3, but I am having trouble to keep the unit registered to trixbox, it disappears from the network every 4 to 5 hours, and then I have to power cycle the unit. I did not do any change to the xml file, I just configured the unit via web browser, so I am not sure if I have to do the changes in xml file and then feed the file via tftp or its ok like that. In case if it is necessary to do the changes in the xml file how I can grab the xml file from the unit, the xml file I downloaded from the provider is for firmware ver:1.00.22. Thanks for the help.
arsh |
|
mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| said by arsh :..., it disappears from the network every 4 to 5 hours, and then I have to power cycle the unit. I had had that problem when testing with my PAP2v2 before. I also noticed my Uniden UIP1869V IP Phone / router also had similar problem until I set both the Polling Interval and Image Download Retry Interval options, under the Provisioning menu, to 0. I haven't tested this on my PAP2v2, yet; however, I thought it won't hurt if you give it a try. Let us know if this will help. |
|
arsh
join:2007-03-06
L'Ile-Bizard, QC
| Hi mazilo,
I tried all the settings you have mentioned but result is same, the unit disappears from the network after 4 to 5 hours. Here are the settings of the pap2v2,
Line1
proxy_fqdn and reg_fqdn= ip address of trixbox
proxy_port and reg_port= 5060
Line2
proxy_fqdn and reg_fqdn= xxxx.dyndns.org
proxy_port and reg_port= 5060
SIP
proxy_fqdn and reg_fqdn= left empty
proxy_port and reg_port= left empty
udp_listen_port=5060
tcp_listen_port=5060
rtp_port_start=default
rtp_port_end=default
Trixbox under sip_additional_conf
[2004]
username=2004
type=friend
secret=xxxx
record_out=Adhoc
record_in=Adhoc
qualify=yes
port=5060
nat=route
mailbox=2004@device
host=dynamic
dtmfmode=rfc2833
disallow=all
context=from-internal
canreinvite=no
callerid=Test
allow=ulaw,alaw
insecure=port,invite
rfc2833compensate=yes
[2005]
username=2005
type=friend
secret=xxxx
record_out=Adhoc
record_in=Adhoc
qualify=yes
port=5060
nat=route
mailbox=2004@device
host=dynamic
dtmfmode=rfc2833
disallow=all
context=from-internal
canreinvite=no
callerid=Test
allow=ulaw,alaw
insecure=port,invite
rfc2833compensate=yes
Any help on this one please.
arsh
|
|
