http://www.dslreports.com/forum/r19213498 en Fri, 27 Nov 2009 17:50:59 EDT Fri, 27 Nov 2009 17:50:59 EDT http://www.dslreports.com/forum/remark,19214515 Bicephale : I'm seeking gurus myself so i guess you meant gargoyle...

:D]]> http://www.dslreports.com/forum/remark,19214515 Sun, 07 Oct 2007 21:36:26 EDT http://www.dslreports.com/forum/remark,19214461 anon : Hey. Thanks. You are definitely a tech guru.

Will try this out.]]> http://www.dslreports.com/forum/remark,19214461 Sun, 07 Oct 2007 21:27:54 EDT http://www.dslreports.com/forum/remark,19213498 Bicephale : Hi Jo,

I thought nobody would be curious enough to ask...



Here's what i'd suggest you try, this should work:

Home > Toolbox > Remote Assistance

1st enable Remote Assistance!  If it's unavailable
then you might have to return to factory settings:

Home > SpeedTouch > Configuration > Reset

Take notes while on the Remote Assistance page and
type these few TelNet CLI commands, starting with:

service system ifadd name=PING_RESPONDER group=wanservice system modify name=PING_RESPONDER state=enabledsaveall
Being "Pingable" is probably required but i didn't
attempt to verify it, though i testify that what's
next is absolutely mandatory so don't forget this:

service system ifadd name=TELNET group=wanservice system modify name=TELNET state=enabledsaveall
Now, if the Remote Assistance page is available it
means that the TelNet CLI would also be accessible
but i don't use an external router so i leave this
matter for others to clear out.  Remember that the
GUI is sercure (HTTPS) but TelNet isn't and that's
why the default duration is set to twenty minutes.

]]> http://www.dslreports.com/forum/remark,19213498 Sun, 07 Oct 2007 18:23:11 EDT http://www.dslreports.com/forum/remark,19213134 anon : Thanks Bicephale. I got this STMT installed but couldn't get it to connect. Tried the 76.xx and 206.xx ips with no luck. I could ping my 76.xx no problem. Wondering what's wrong though.

And anybody has answers for the other question.

THX.]]> http://www.dslreports.com/forum/remark,19213134 Sun, 07 Oct 2007 17:00:45 EDT http://www.dslreports.com/forum/remark,19212906 Bicephale : Jo> Don't want to reset the modem and set up again just to use DMT.


SpeedTouch 516 Tweaking &58;&41;, Bicephale, 2007-Sep-30]]> http://www.dslreports.com/forum/remark,19212906 Sun, 07 Oct 2007 16:15:44 EDT http://www.dslreports.com/forum/remark,19211514 anon : So I just activated my Teksavvy. Don't know if I should post here for some DSL setup questions. Please move to another thread if it's not belong to here.

1) I setup my Speedtouch 516 to Bridge mode and connected to the my router. Setup MTU in both to 1492. Do I have to set my other PCs connected to the router as well or it will be OK?

2) Do I HAVE to connect to the modem directly in order to use DMT or any other way to do it via the router?
Try to connect to modem directly with no success. I think it's probably that I can't get an IP since it's in Bridge mode. Don't want to reset the modem and set up again just to use DMT.

3) I have installed filters on all outlets with phones connected. However there's security dialer in the basement with the wire spliced to connect to a junction block. I probably need to put a filter in between. However, correct me if I'm wrong, the security dialer won't be activated and dialed out (unless a break in). Do I still need a filter since it's not used? Same thing goes to the fact that no filters need if no phones used in house.

So far my line is quite stable at 3.5M download. I know I might have look at the line stat to see if I need the extra filter.

Thanks in advance.]]> http://www.dslreports.com/forum/remark,19211514 Sun, 07 Oct 2007 10:54:12 EDT