Search:  

 
 
   All ForumsHot TopicsGallery






how-to block ads


 
Forums » Equipment Support » Hardware By Brand » 2Wire » 2Wire 2700HG-B Problem - Blinking DSL Red Light
Search Topic:
Share Topic:
RSS topic:
toggle:
flat / full
normal / watch
Posting:
Post a:
Post a:
Voip question »
« no activity being received wireless thru my 2wire 1000sw  
AuthorAll Replies


scsa20

@cox.net

reply to Gwai Lo Dan
Re: 2Wire 2700HG-B Problem - Blinking DSL Red Light

said by Gwai Lo Dan See Profile :

Since you have an active DSL line with Bell, the modem's red DSL light means your modem is NFG (i.e., a dud). Exchange it.
Just because the line is "activated" doesn't mean it's actually activated. It's normally up to the local telco company to make the decision on that if it's an issue with the modem or not.

Generally speaking, a flashing red DSL light means the modem is not getting the DSL signal. This could be due to many different reasons.

First, make sure all your phones (including home alarm systems, satellite systems, and intercoms) has filters on them. If you need to, take the modem and plug it directly into the NID.

I would also contact your ISP and request for them to do a line test if plugging the modem into the NID gave you the same problems.

Also, if you have more then 1 number going through your jacks, then you're going to need what's call a 2-line DSL filter.

Also note that you might also need to go into 192.168.1.254/setup to replace the keycode that's currently in there with one that will match your ISP's setup or closely related before it picks up the DSL signal (you have no ideal how many times I've seen these modems does weird things like that).


Gwai Lo Dan

join:2007-01-24
St Catharines, ON
·CIKTEL Telecom

said by scsa20 :

Just because the line is "activated" doesn't mean it's actually activated. It's normally up to the local telco company to make the decision on that if it's an issue with the modem or not.
Note that he said he is currently with Bell. Thus, he already has DSL and is changing DSL providers. For this reason, if the DSL light is red, he has a dud.


scsa20

@cox.net

Note that he also said that he canceled Bell so it could also mean that Bell already disconnected the line.

Also note that the 2Wire modem needs a very clean line in order for it to work successfully.

If I was in buju shoes, I would wait until Teksavvy becomes active, and if he continues to get the red DSL then he would probably need to contact Teksavvy for a line test.
Forums » Equipment Support » Hardware By Brand » 2WireVoip question »
« no activity being received wireless thru my 2wire 1000sw  


Tuesday, 10-Nov 22:54:12 Terms of Use | Privacy Policy | Hosting by www.nac.net - DSL,Hosting & Co-lo | feedback | contact
over 10 years online! © 1999-2009 dslreports.com.
page compression OFF
Most commented news this week
· [125] Moto Sold About 100,000 Droids
· [94] Verizon Keeps Swinging At AT&T
· [86] VoIP Over 3G Still Not Working For iPhone
· [67] Government Will Release Some Telco Wiretap Lobbying Documents
· [62] Verizon's Hanging Up On Rural America
· [47] Verizon's Higher ETFs Annoy Senator
· [34] Bill Would Force ISPs To Block Financial Scams
· [31] Sprint Announces Job Cuts
· [24] Mediacom Hints At 50, 100 Mbps Speeds
· [21] Google Offers Free Holiday Airport Wi-Fi
Most people now reading
· House inspector failed to find major gas leak [Home Repair & Improvement]
· RG Firmware update to VDSL2 this morning [AT&T U-verse]
· Water heater pilot light won't light [Home Repair & Improvement]
· Google Has Acquired Gizmo5 [VOIP Tech Chat]
· Windows 7 boot manager editing questions [Microsoft Help]
· Slow speed lately? [TekSavvy]
· Tomato/MLPPP v3 alpha 6 released! [TekSavvy]
· Holy work line speeds!! [TekSavvy]