Parnelli Jones
@charter.com
| Cisco 804 ISDN TA looses it's mind
I purchased a 804 Series ISDN Lan TA and for some reason it will lose it's mind.
It connects to the internet fine sometimes then after a few hours won't dial on demand no matter what I do. I can powercycle, reboot, whatever and nothing.
I've actually taken it off the ISDN line to see if that will reset it.
I'll post the config file tonight here. Any help appreciated. |
|
Parnelli
join:2008-01-04
New Market, TN
| Config. Yes, I am Parnelli Jones.
Current configuration : 2910 bytes
!
version 12.2
no service single-slot-reload-enable
no service pad
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname xxxxxxxxxx
!
boot system flash:c800-y6-mw.122-1
logging buffered 8192 debugging
logging rate-limit console 10 except errors
enable secret 5 xxxxxxxxxxxxxxxxxxxx
!
username xxxxxxx password 7 xxxxxxxxxxxxxx
!
dial-peer voice 1 pots
caller-id
call-waiting
ring 0
registered-caller ring 1
port 1
destination-pattern xxxxxxx
!
dial-peer voice 2 pots
caller-id
call-waiting
ring 0
registered-caller ring 1
port 2
destination-pattern xxxxxxx
!
pots country US
ip subnet-zero
no ip source-route
!
ip dhcp pool DHCPPoolLAN_0
network 192.168.10.0 255.255.255.0
dns-server 209.210.176.8 209.210.176.9
default-router 192.168.10.1
!
ip name-server 209.210.176.8
ip name-server 209.210.176.9
no ip finger
no ip dhcp-client network-discovery
isdn switch-type basic-ni
!
!
!
interface Ethernet0
ip address 192.168.10.1 255.255.255.0
ip access-group 121 in
no ip proxy-arp
ip nat inside
!
interface BRI0
no ip address
encapsulation ppp
dialer pool-member 1
isdn switch-type basic-ni
isdn spid1 xxxxxxxxxxxxxx xxxxxxx
isdn spid2 xxxxxxxxxxxxxx xxxxxxx
isdn incoming-voice modem
cdapi buffers regular 0
cdapi buffers raw 0
cdapi buffers large 0
ppp authentication chap pap callin
ppp multilink
ppp timeout multilink link remove 2399
!
interface Dialer0
no ip address
no cdp enable
!
interface Dialer1
description ISP
ip address negotiated
ip access-group 121 in
no ip proxy-arp
ip nat outside
encapsulation ppp
no ip split-horizon
dialer pool 1
dialer remote-name xxxxxxx
dialer idle-timeout 2400
dialer string xxxxxxx class DialClass
dialer string 6844134
dialer hold-queue 10
dialer load-threshold 10 either
dialer-group 1
pulse-time 0
ppp authentication chap pap callin
ppp chap hostname xxxxxxxxxxxxx
ppp chap password 7 xxxxxxxxxxxxxx
ppp pap sent-username xxxxxxxxx password 7 xxxxxxxxxxxxxxxxx
!
ip nat inside source list 18 interface Dialer1 overload
ip http server
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer1
!
!
map-class dialer DialClass
dialer isdn speed 64
access-list 18 permit 192.168.10.0 0.0.0.255
access-list 121 deny udp any eq netbios-dgm any
access-list 121 deny udp any eq netbios-ns any
access-list 121 deny udp any eq netbios-ss any
access-list 121 deny tcp any eq 137 any
access-list 121 deny tcp any eq 138 any
access-list 121 deny tcp any eq 139 any
access-list 121 permit ip any any time-range TIME
dialer-list 1 protocol ip permit
!
line con 0
exec-timeout 120 0
transport input none
stopbits 1
line vty 0 2
exec-timeout 0 0
login local
line vty 3
exec-timeout 0 0
password 7 xxxxxxxxxxxxxxxxxx
login local
line vty 4
exec-timeout 0 0
login local
!
!
time-range TIME
periodic daily 0:00 to 23:59
!
end
By the way, leaving the TA off and disconnected from the IDSN line did no good. I'm back to using my old reliable 3com Office Connect Lan TA.
--
Parnelli
The master of bad jokes and ruler of the land of odd.
Let's go Flyers! |
|
Parnelli
join:2008-01-04
New Market, TN
| ....UPDATE....
I got a config file from someone that has one of these units, changed it to match my information (SPIDs, Dialin number) and also got a new flash file from him. I updated the TA and all is now well. The TA connects without any issues and works like it did before. I have no clue what it's issue was.
Thanks for all the help.
--
Parnelli
The master of bad jokes and ruler of the land of odd.
Let's go Flyers! |
|
