http://www.dslreports.com/forum/r20326495 en Thu, 03 Dec 2009 09:04:30 EDT Thu, 03 Dec 2009 09:04:30 EDT http://www.dslreports.com/forum/remark,20361707 kubaff :
Did you adjust the config register ?]]> http://www.dslreports.com/forum/remark,20361707 Mon, 21 Apr 2008 07:59:11 EDT http://www.dslreports.com/forum/remark,20361704 kubaff :
Did you adjust the config register to 0x2102 ?]]> http://www.dslreports.com/forum/remark,20361704 Mon, 21 Apr 2008 07:58:59 EDT http://www.dslreports.com/forum/remark,20341231 rolande : It is possible that the config-register got changed on the switch which adjusted the console port speed settings. Typically you might see garbage on the terminal client if the console port is running at higher speed. Unfortunately, if that is the case, the only way to recover is to guess the line speed by manual testing.

Have you verified that the switch port lights are not lit amber and staying that way through the POST? You should see the lights flash as it is booting.
--
Ignorance is temporary...stupidity lasts forever!

»www.thewaystation.com/
»blog.thewaystation.com/]]> http://www.dslreports.com/forum/remark,20341231 Tue, 15 Apr 2008 23:52:37 EDT http://www.dslreports.com/forum/remark,20337243 drpain : no output appears. It appears as if the keystrokes are not registering]]> http://www.dslreports.com/forum/remark,20337243 Tue, 15 Apr 2008 11:38:33 EDT http://www.dslreports.com/forum/remark,20332505 rolande : You're not reading my post. I am not talking about the switch configuration. I am talking about your terminal client on your PC. If you can see the text output on the terminal screen but when you type nothing shows up, then you either have an incorrect flow control setting in your terminal client, local echo is disabled, or there is a bad pinout on your terminal cable.

Also you can fix this issue of the switch booting to ROMMON by adjusting the config-register to 0x2102 and/or configuring 'boot system flash:imagename.bin'. Do a dir on your flash to see what IOS image is booting and you can configure that manually to boot at startup so you don't have to do it yourself each time.]]> http://www.dslreports.com/forum/remark,20332505 Mon, 14 Apr 2008 14:45:19 EDT http://www.dslreports.com/forum/remark,20330462 drpain : nomally when it prompts me to ROMMON Mode i just type boot and that is it. it boots fine but now i cannot type any letter. How can i resolve this
please assist.]]> http://www.dslreports.com/forum/remark,20330462 Mon, 14 Apr 2008 06:36:29 EDT http://www.dslreports.com/forum/remark,20328015 rolande : Did you check to make sure you didn't disable local echo or change your flow control settings in the terminal client? Had this exact same issue with a Juniper/Netscreen firewall and it turned out to just be a flow control issue. I disabled all flow control and *bam* it worked. ;)]]> http://www.dslreports.com/forum/remark,20328015 Sun, 13 Apr 2008 16:53:05 EDT http://www.dslreports.com/forum/remark,20327888 Domwilko : What's the output when you type 'set' from ROMMON?
--
Domwilko - CCVP, CCNP, CCNA, CCDA]]> http://www.dslreports.com/forum/remark,20327888 Sun, 13 Apr 2008 16:10:30 EDT http://www.dslreports.com/forum/remark,20326495 drpain : i rebooted my cisco 4503 switch then it went to rommon mode.
normally when it prompts me to this mode i usually type boot then it boot.
Now the issue is i cannot type anything in hyper terminal window yet my keyboard is working.

any idea of what is happening and how i can resolve it

rommon mode.txt 578 bytes

]]> http://www.dslreports.com/forum/remark,20326495 Sun, 13 Apr 2008 10:15:03 EDT