http://www.dslreports.com/forum/r20447471 en Thu, 20 Nov 2008 20:53:06 EDT Thu, 20 Nov 2008 20:53:06 EDT http://www.dslreports.com/forum/remark,20450318 CCat : I left the battery out last night and set everything this morning. Checked CPUZ and all is well in OC land. Thanks for the info.
--
Graphics Playground]]> http://www.dslreports.com/forum/remark,20450318 Thu, 08 May 2008 08:47:56 EDT http://www.dslreports.com/forum/remark,20448908 CCat : Rev 2.1]]> http://www.dslreports.com/forum/remark,20448908 Wed, 07 May 2008 22:43:06 EDT http://www.dslreports.com/forum/remark,20448887 Gooiool : CPU host clock control......Enabled
That's been my pain or ( thorn in the past )forgetting to Enable CPU host clock control.

Also What Version is your MB 2.0 just wondering ?
--
Team DiscoveryJoin us help fight cancer.
Gooiool©2005 My Photo Site]]> http://www.dslreports.com/forum/remark,20448887 Wed, 07 May 2008 22:39:39 EDT http://www.dslreports.com/forum/remark,20447780 signmeuptoo : reflash BIOS maybe, and with something newer if there is such a thing. But first try a long time period CMOS reset. Leave the jumper in place for a few hours WITH THE POWER SUPPLY TURNED OFF!!!]]> http://www.dslreports.com/forum/remark,20447780 Wed, 07 May 2008 19:06:11 EDT http://www.dslreports.com/forum/remark,20447471 CCat : The mobo is a Gigabyte GA P35 DS4 with F11 bios
Ram is 8GB (4x2GB) Corsair XMS2 6400C5DHX
CPU is Intel Q6600 Quad
--
Graphics Playground]]> http://www.dslreports.com/forum/remark,20447471 Wed, 07 May 2008 18:04:52 EDT http://www.dslreports.com/forum/remark,20447391 Sc0tt : what hardware you running?

mobo
ram
cpu]]> http://www.dslreports.com/forum/remark,20447391 Wed, 07 May 2008 17:51:01 EDT http://www.dslreports.com/forum/remark,20446035 CCat : My computer has been running at 3.6 doing fine. I tried a screen capture program which didnt work well. I uninstalled it which didnt go real smooth. My system rebooted on its own and the bios stated update success but I didnt change any settings.
I went back to the bios and made sure all the settings were OK then saved to CMOS and exited. CPUZ still showed my CPU at 2.4 with a 266 FSB. I powered down and cleared the CMOS. Made sure my settings in the bios were right and saved. Boot screen showed update success. Still wont OC stays at std speed. Vcore shows the increase and ram settings are good.

Heres what I have for settings:

Robust graphics adapter.....Auto
CPU clock ratio.............9X
CPU host clock control......Enabled
CPU host frequency..........400
PCI express frequency.......100
C.I.A.2.....................Disabled
Performance enhanced with...Std
System memory multiplier....2.0

DRAM timing table...........Manual
Std timing control..........4
CAS latency time............4
DRAM Ras to CAS delay.......4
DRAM RAS precharge..........4
Precharge delay.............12
Ram is originally 5 5 5 18

Advanced timing control.....All auto

System voltage control......Manual
DDR2 overvoltage control....+.30
PCI-E overvoltage control...Normal
FSB overvoltage control.....+.35
(G)MCH overvoltage control.+.30
Loadline calibration.......Enabled
CPU voltage control........1.35

Limit CPUID max to 3.......Disabled
No execute memory protect..Enabled
CPU enhanced halt (CIE)....Disabled
CPU thermal monitor........Enabled
CPU EIST function..........Disabled
Visualization technology...Disabled

Any help would be much appreciated as it is driving me CRAZY.
--
Graphics Playground]]> http://www.dslreports.com/forum/remark,20446035 Wed, 07 May 2008 13:58:07 EDT