Search:  

 
 
   All ForumsHot TopicsGallery






how-to block ads


 
Forums » Up and Running » Networking » How do I determine subnet manually?
Search Topic:
Share Topic:
RSS topic:
toggle:
flat / full
normal / watch
Posting:
Post a:
Post a:
[XP] Need new NIC »
« Any way to set a "Hard" Cap with router?  
AuthorAll Replies


tschmidt
Premium,MVM
join:2000-11-12
Milford, NH
·Verizon Online DSL

reply to verifone411
Re: How do I determine subnet manually?

Each octet is 8-bits. A /24 address means 24-bits of address are reserved for network leaving 8 for host. This assumes you are talking about IPv4 with a 32-bit address range.

An Octet is FFh or 256 (in decimal notion) However, since the lowest address is reserved as network address and highest for broadcast that leaves 254 available host addresses.

Dotted Decimal was a convenient way to represent IP address when Class-full addressing was used since Class boundaries were also octet boundaries. With the advent of classless routing where split between network and host address can occur anywhere dotted decimal is a little like using Roman numerals to build a house.

If you stick with binary or hex it is a lot less confusing.

/tom

IamGimli

join:2004-02-28
Canada
·Primus Talkbroadband
·B2B2C High-Speed I..

said by tschmidt See Profile :

If you stick with binary or hex it is a lot less confusing.
I understand binary but how is hexadecimal any less confusing than decimal to represent network addresses? It may make them a bit shorter to write but I don't see any difference in the confusion aspect.


tschmidt
Premium,MVM
join:2000-11-12
Milford, NH
·Verizon Online DSL

said by IamGimli See Profile :

I understand binary but how is hexadecimal any less confusing than decimal to represent network addresses? It may make them a bit shorter to write but I don't see any difference in the confusion aspect.
Dotted decimal represents a discontinuous counting method. If I add 1 to FFh I get 100h. If I add 1 to 0.255 (dotted decimal) I get 1.0. Life gets even more exciting if I start playing with masking lower order bits.

If I want to mask the 2 low order bits I have
1111 1100 b (binary)
FCh (hex)
252 Decimal

Perhaps I'm unique (after all this is not my day job) but I find it impossible to do arithmetic in dotted decimal.

/tom
Forums » Up and Running » Networking[XP] Need new NIC »
« Any way to set a "Hard" Cap with router?  


Monday, 06-Oct 09:11:51 Terms of Use | Privacy Policy | Hosting by www.nac.net - DSL,Hosting & Co-lo | feedback | contact
over 9 years online! © 1999-2008 dslreports.com.republican-creole
page compression OFF
Most commented news this week
· [124] Friday Open Thread
· [115] Caps: Innovation Killer?
· [93] Shocker: Consumers Hate Broadband Caps
· [88] $700 Billion Would Buy A Lot Of Fiber
· [87] When Will U-Verse Customers See Faster Speeds?
· [84] Cox Employs 'Three Strikes' DMCA Policy
· [78] Cox Responds to DMCA 'Three Strikes' Report
· [64] Electrical Expert: FiOS Installations Safe
· [63] Tough Economy? Consumers Will Keep Broadband
· [61] Qwest Union Workers Reject Offer
Most people now reading
· No more usage checker? [TekSavvy]
· Extreme HD and Essentials [Verizon FIOS TV]
· IMG 1.6 Build 06.89 Released [Verizon FIOS TV]
· [XPAV infection?] Cannot log in to windows, nor safe mode [Security]
· [XP Home] I can't get past blue screen [Microsoft help]
· Heads up; Usenet, "Rarpassgen.exe" virus [TekSavvy]
· new internet tax ? [TekSavvy]
· Extjs grid combo box. [Webmasters and Developers]