dslreports logo
site
 
    All Forums Hot Topics Gallery
spc

spacer




how-to block ads


Search Topic:
uniqs
41
share rss forum feed


Doctor Olds
I Need A Remedy For What's Ailing Me.
Premium,VIP
join:2001-04-19
1970 442 W30
kudos:18
reply to solitaire321

Re: How to get to configuration menu in Zyxel P-660R-D1


solitaire321

join:2008-06-24
Washington, DC
said by Doctor Olds:

How do you know which of the 3 models of P660R that Earthlink provides that you have is the D1?

There are 3 Sub Models so far and they are each a little different in how they work.
I know because when I type the 192.168.x.x number in my browser, the modem home page where it asks you to login says "P-660R-D1" at the top...


Doctor Olds
I Need A Remedy For What's Ailing Me.
Premium,VIP
join:2001-04-19
1970 442 W30
kudos:18
OK, That is the Firmware installed, but does the label on the bottom match up? You may have a mismatch.

Did you successfully reset the unit?

Regards,

Doctor Olds
--
What’s the point of owning a supercar if you can’t scare yourself stupid from time to time?

solitaire321

join:2008-06-24
Washington, DC

1 edit
said by Doctor Olds:

OK, That is the Firmware installed, but does the label on the bottom match up? You may have a mismatch.

Did you successfully reset the unit?

Regards,

Doctor Olds
Sorry it took me so long to respond, I've been very busy lately. But I did take a look at the bottom of the modem and it is the P-660R-D1. Also, because my modem is connected to a router and not a computer, I tried turning the router off and then resetting the modem, but when I turned them both back on I still had the same problem. I uploaded this pic »i353.photobucket.com/albums/r383···pic2.jpg which is number 11 at the website (»kb.earthlink.net/case.asp?article=8226) but with squiggly lines to show what I don't have. Interestingly, the only thing I do have that the picture doesn't is I have a button to log out in the corner. My modem is in routing mode if that is important.

Basically I want to get those options on the left so I can open some ports in my firewall because at the moment I can't get to the firewall in the modem. Thanks


Doctor Olds
I Need A Remedy For What's Ailing Me.
Premium,VIP
join:2001-04-19
1970 442 W30
kudos:18
said by solitaire321:

Also, because my modem is connected to a router and not a computer, I tried turning the router off and then resetting the modem, but when I turned them both back on I still had the same problem.
Remove the Router. Reset the ZyXEL and hook it directly to the PC.

Regards,

Doctor Olds
--
What’s the point of owning a supercar if you can’t scare yourself stupid from time to time?

solitaire321

join:2008-06-24
Washington, DC
Is it at all possible to get to the menu without hooking the modem up directly to the PC? I feel like I have been able to do it before when the modem was not hooked directly up to the PC.

solitaire321

join:2008-06-24
Washington, DC
Anyway, I did hook up the modem directly to the PC and I got what I was looking for! I also switched the mode from routing to bridging and hooked it back to the router and got internet fine. Now the problem is I can't get to the modem status page anymore by going to 192.168.1.1. Is it even possible to do so anymore, and if so, how? Thanks!


Doctor Olds
I Need A Remedy For What's Ailing Me.
Premium,VIP
join:2001-04-19
1970 442 W30
kudos:18
said by solitaire321:

Anyway, I did hook up the modem directly to the PC and I got what I was looking for! I also switched the mode from routing to bridging and hooked it back to the router and got internet fine. Now the problem is I can't get to the modem status page anymore by going to 192.168.1.1. Is it even possible to do so anymore, and if so, how? Thanks!
In Bridge Mode the Modem is invisible to the connection. So no, you are unable to access the ZyXEL when you put a Router in the way as it has PPPoE running which gives the Router your Public IP. Since the Modem has a Private range IP, the Router doesn't allow routing from its Public IP to any Private IPs on its WAN side. Standard Internet RFC stuff.

Now you can change your Router from PPPoE to DHCP Automatically Obtain an IP, but with the Modem in Bridge Mode, it is no longer handing out Private IPs since its DHCP server is disabled while Bridged. In order to access the Modem, you would have to reset it. Then you would have access to the Modem again, but you have disconnected your Internet connection to do so.

Regards,

Doctor Olds
--
What’s the point of owning a supercar if you can’t scare yourself stupid from time to time?

Bwuutje

join:2005-01-10
No, you do not need to reset your modem.

You can just give your pc an ip-address in the 192.168.1.x range, hook it up to the modem and access it again on 192.168.1.1. But the pc wont have internet access at that time. But you can check your modem this way.

Bwuutje.


Doctor Olds
I Need A Remedy For What's Ailing Me.
Premium,VIP
join:2001-04-19
1970 442 W30
kudos:18
said by Bwuutje:

No, you do not need to reset your modem.

You can just give your pc an ip-address in the 192.168.1.x range, hook it up to the modem and access it again on 192.168.1.1. But the pc wont have internet access at that time. But you can check your modem this way.
For that to work, you would have to remove the Router out of the way and hook directly to the ZyXEL. What you propose would not work with the Router in place.
--
What’s the point of owning a supercar if you can’t scare yourself stupid from time to time?

solitaire321

join:2008-06-24
Washington, DC
OK. So I set it back to routing mode and can still get to the wizard setup thing. Now because the modem and router are both running a firewall, is it ok to disable NAT in the modem and keep the firewall in the router? Or is it better to keep both? I want to be able to forward ports easily. Thanks for your help so far!


Doctor Olds
I Need A Remedy For What's Ailing Me.
Premium,VIP
join:2001-04-19
1970 442 W30
kudos:18
The simplest, least complicated way to have Port Forwarding available is to have the ZyXEL P660R DSL Modem/Router set in Bridge Mode when you have a second Router so that Port Forwarding entries need to be setup just once in the Router that is handling the PPPoE.

Once you use the ZyXEL as a Router then you will have Doubled-NAT/NAPT and that makes Port Forwarding harder as you have to setup Port Forwarding in both Routers and all packet will be translated twice each direction which sometimes can break some applications or games.

Regards,

Doctor Olds
--
What’s the point of owning a supercar if you can’t scare yourself stupid from time to time?