BTB
@sbcglobal.net
| [XP Home] Boot. Then Wait 2 Minutes Before I Can Connect
Cannot figure this out. If you seen this question before, a reply with a link would be appreciated if you prefer. I tried searching for answer, but have not found anything.
Problem is as stated in the subject. Issue started after a re-installation of XP.
Computer cannot get onto the internet for 2 minutes after the boot process is finish. No matter what internet application is launched, it will just keep on searching for a connection until the 2 minutes is up. After that, the application will load with the data it just downloaded. Everything afterwards will be normal until the next boot when I will have to wait for 2 minutes again.
I checked the Internet Options/Connections/LAN Settings and unchecked everything. Still the same thing happens. This is getting annoying. Any ideas on how this can be fixed?
Thanks. |
|
BTB
@sbcglobal.net | Bump in hopes that someone will have a suggestion. |
|
craig70130
Premium
join:2004-04-27
New Orleans, LA | reply to BTB
Do you have an IP address while this is happening? (ipconfig from a command prompt)
If not, I'd suspect a networking issue. |
|
Bornloser
join:2002-09-04
Cleveland, OH | reply to BTB
Have you tried disabling your AV/Firewall software temporarily? I find that I cannot connect or do anything else until my AV downloads updates at startup and does a quick scan. I've learned to live with it. Using ESET Smart Security. |
|
Airwolf
Don't be shy now. Come on, catch a ride
Premium
join:2001-10-30
Windsor, ON
clubs:
3 edits | reply to BTB
Are you using DSL and a modem that is only configured in bridge mode (not a hybrid router/modem configuration that supports DHCP)?
Try setting a static IP for your NIC.
i.e.
IP address 192.168.0.100
subnet mask 255.255.255.0 |
|
auggy
Premium,Mod
join:2001-12-24
Brockville, ON
 ·Cogeco Cable
 ·Bell Sympatico
Host:
Microsoft Help
| reply to BTB
Also, if you are connecting to the internet using PPPoE software, including XP's built-in PPPoE client, and have not already, try assigning an IP address to TCP/IP bound to your NIC:
»Tweaking FAQ »Stalls and freezes |
|
BTB
@sbcglobal.net
| reply to BTB
Thanks for the replies guys.
1. During the 2 minutes (maybe 1.5) after booting, ipconfig gives me the correct information. Pinging a website works as well.
2. Only AV/Firewall installed is Windows' firewall. Disabled/Enabled did not make a difference.
3. Am using an old Alactel?? DSL modem & a Linksys wired router. Tried setting the static IP, but could not even connect to the internet after the change. I used 10.10.1.XXX, but even inputting that instead of 192.168.1.XXX yielded no connection.
I am at a loss at what is causing this stall. |
|
auggy
Premium,Mod
join:2001-12-24
Brockville, ON | Does the same problem exist if you restart the computer in "Safe Mode with Networking"? |
|
Airwolf
Don't be shy now. Come on, catch a ride
Premium
join:2001-10-30
Windsor, ON
clubs: | reply to BTB
Try without using the router, but set a static IP on the NIC. |
|
BTB
@sbcglobal.net | reply to BTB
Safe mode w/networking works with no waiting. I cannot try it without a router now because other systems are using the network.
Since it works in safe mode, it looks like some program/driver/whatever is the issue. Problem is how to find it. |
|
Unknown_Poster
@verizon.net | said by BTB :
Problem is how to find it. The Event Viewer is always a good place to start. |
|
auggy
Premium,Mod
join:2001-12-24
Brockville, ON
·Cogeco Cable
·Bell Sympatico
Host:
Microsoft Help
| reply to BTB
said by BTB :
Since it works in safe mode, it looks like some program/driver/whatever is the issue. Problem is how to find it.
Try a "clean boot" of XP - Method 2 in the following MS KB article:
»support.microsoft.com/kb/331796
If a "clean boot" works there are further steps in the article to try to determine the problem. |
|
