 Smith6612
MVM
join:2008-02-01
North Tonawanda, NY |
to Joejy
[Interleave/Fastpath] Re: Need to switch between Interleave and FastPath? Part 2Your line should be fine. |
|
| |
to Smith6612
Transceiver Revision A2pB020b3.d19d
Vendor ID Code 4D54
Line Mode ADSL_G.dmt
Data Path INTERLEAVED
Transceiver Information Down Stream Path Up Stream Path
DSL Speed (Kbits/Sec) 3360 864
Margin (dB) 16.9 12.0
Line Attenuation (dB) 38.0 21.0
Transmit Power (dBm) 8.6 11.9
Would fast path work on my line? |
|
Smith6612
MVM
join:2008-02-01
North Tonawanda, NY |
to Chocky
While there is room for FastPath on that line, there isn't much room for variance in the line's margins. You can give it a go, but expect your margins to drop a little bit and don't be surprised if the line syncs at a lower speed. |
|
| |
to Smith6612
Hi Smith6612
I finally got my alarm filter and just installed it. My speed are closer to 3 mbps now. Thanks. I have listed my new stats, is FastPath doable with these stats. Again Thanks in advance for all your help
Transceiver Statistics
Transceiver Revision: 7.2.3.0
Vendor ID Code: 4
Line Mode: G.DMT Mode
Data Path: Interleaved
Transceiver Information Downstream Path Upstream Path
DSL Speed (Kbits/Sec) 3360 832
Margin (dB) 10.0 13.0
Line Attenuation (dB) 48.5 27.5
Transmit Power (dBm) 15.7 11.8 |
|
Smith6612
MVM
join:2008-02-01
North Tonawanda, NY  ·Charter
Ubee EU2251
Ubiquiti UAP-IW-HD
Ubiquiti UniFi AP-AC-HD
1 edit |
to Arachneya
[Interleave/Fastpath] Re: My line keeps disconnecting. Should I switch to Interleaved?You are close enough to take 7.1Mbps + FastPath, however the line may just have some noise on it that is causing the disconnects. Right now the margin is too low to get the full 7.1Mbps speed, but it should be raisable. As per the disconnects, have you looked at your modem logs at all? Those will help. |
|
1 edit |
to Smith6612
[Interleave/Fastpath] My line keeps disconnecting. Should I switch to Interleaved?Hey Smith/Jodokast,
I switched to Fastpath last Novemeber. The latency/connection improvement was substantial. Last month, it started disconnecting randomly. Lately, it's been doing do several times a day, rendering long sessions of online gaming impractical.
Do I have to switch back to Interleaved or has my line quality degraded?
***
Transceiver Revision: 7.2.3.0
Vendor ID Code: 4
Line Mode: G.DMT Mode
(Transceiver Information) (Downstream) (Upstream)
DSL Speed (Kbits/Sec) 3360 864
Margin (dB) 13.5 11.0
Line Attenuation (dB) 27.0 15.0
Transmit Power (dBm) 6.9 11.9
***
Can I get 7 Mbps? Thanks. |
|
 sashwa
Mod
join:2001-01-29
Alcatraz |
to Smith6612
[Interleave/Fastpath] (topic move) Need to switch between Interleave and FastPath? ParModerator ActionThe post that was here, has been moved to a new topic .. » [Split] Would my line be good for 7 Mb? |
actions · 2009-Feb-13 11:30 pm · (locked) |
|
 Jodokast96Stupid people piss me off.
Premium Member
join:2005-11-23
NJ |
to Kithron
[Interleave/Fastpath] Re: Need to switch between Interleave and FastPath? Part 2Yes to both. |
|
 Kithron
Premium Member
join:2005-08-30
Binghamton, NY
Netgear RAX200
|
to Smith6612
Is my line good for fastpath / 7mb?
Transceiver Revision: 7.2.3.0
Vendor ID Code: 4
Line Mode: ADSL2+ Mode
Data Path: Interleaved
Transceiver Information Downstream Path Upstream Path
DSL Speed (Kbits/Sec) 3355 863
Margin (dB) 26.0 13.0
Line Attenuation (dB) 38.5 21.5
Transmit Power (dBm) 19.2 12.1 |
|
Smith6612
MVM
join:2008-02-01
North Tonawanda, NY |
to Bullet2k4
Yes, your line is good to go for FastPath  |
|
| |
to Smith6612
i think my connection switch to interleave after an upgrade
Transceiver Revision: 7.2.3.0
Vendor ID Code: 4
Line Mode: G.DMT Mode
Data Path: Interleaved
Transceiver Information Downstream Path Upstream Path
DSL Speed (Kbits/Sec) 1184 448
Margin (dB) 15.0 16.0
Line Attenuation (dB) 52.5 31.5
Transmit Power (dBm) 11.5 11.8
fastpath? |
|
Smith6612
MVM
join:2008-02-01
North Tonawanda, NY |
to Chocky
Give your alarm company a call and tell them you have DSL. They should be able to tell you what to do in order to filter that. |
|
| |
to Smith6612
Thanks Smith6612 for your quick reply, I have filter on all my phone lines, but just realized that there is a phone connection hard wired into my Home security system, I am going to have to find out how to add the filter onto it, because I think that might be my source of loosing the sync. I will post my result after that. |
|
Smith6612
MVM
join:2008-02-01
North Tonawanda, NY |
to ccisneros
Your downstream margin of 6 won't cut it, sorry. Enjoy the new speed though! |
|
| |
to Smith6612
Thanks for replying to my post Smith! I got a new actiontech router and upgraded my speed to 7.1Mbps. Here are my new stats. How does it look for FastPath?
DSL Status
VPI: 0
VCI: 32
DSL Mode Setting: MMODE
DSL Negotiated Mode: ADSL2PLUS
Connection Status: SHOWTIME
Speed (down/up): 7530/863
ATM QoS class: UBR
Near End CRC Errors : 0/0
Far End CRC Errors : 1/0
Near End CRC(Within last 30 mins) : 0/0
Far End CRC(Within last 30 mins) : 0/0
Near End RS FEC : 0/0
Far End RS FEC :4136/0
Near End FEC(Within last 30 mins) : 0/0
Far End FEC(Within last 30 mins) :0/0
Discarded Packets(Within last 30 mins): 0
SNR Margin (Downstream/Upstream): 6/13
Attenuation (Downstream/Upstream): 38/22
Thanks!
Cesar |
|
Smith6612
MVM
join:2008-02-01
North Tonawanda, NY ·Charter
Ubee EU2251
Ubiquiti UAP-IW-HD
Ubiquiti UniFi AP-AC-HD
2 edits |
to chocky
Chocky, Your line is provisioned at 3Mbps, not at the 1.5Mbps speed, so you are obviously losing your sync. See if you can clean up the line to get the margins a little higher so that you can get the 3Mbps speed, and then we'll see if you can get FastPath after that. The proper sync rate for 3Mbps is 3360/864.
Buckettruck, your line is good. |
|
| |
to Smith6612
Here are my stats, fastpath or not i am supposed to get 3M and only get 1.5M Transceiver Statistics Transceiver Revision: 7.2.3.0 Vendor ID Code: 4 Line Mode: ADSL2+ Mode Data Path: Interleaved Transceiver Information Downstream Path Upstream Path DSL Speed (Kbits/Sec) 1787 447 Margin (dB) 15.0 23.0 Line Attenuation (dB) 52.5 33.0 Transmit Power (dBm) 16.3 11.9 |
|
| |
chocky to Smith6612
Anon
2009-Feb-10 10:30 pm
to Smith6612
Here is my info. Any good for fastpath, I am supposed to get 3 Mbps but currently topping out at 1.5 Mbps. Thanks in advance for your help.
Transceiver Revision: 7.2.3.0
Vendor ID Code: 4
Line Mode: G.DMT Mode
Data Path: Interleaved
Transceiver Information Downstream Path Upstream Path
DSL Speed (Kbits/Sec) 1856 832
Margin (dB) 14.5 12.0
Line Attenuation (dB) 45.5 25.5
Transmit Power (dBm) 16.1 11.8 |
|
Smith6612
MVM
join:2008-02-01
North Tonawanda, NY |
to Tampa304
[Interleave/Fastpath] Re: Westell 7500 ModemYour line is good to go for FastPath. |
|
| |
to Smith6612
[Interleave/Fastpath] Westell 7500 ModemAm posting my Transceiver Information. Would my connectivity improve if I switch to FastPath? Thanks for your help!  Transceiver Revision A2pB020b3.d19d Vendor ID Code 4D54 Line Mode ADSL_G.dmt Data Path INTERLEAVED Transceiver Information Down Stream Path Up Stream Path DSL Speed (Kbits/Sec) 1184 448 Margin (dB) 13.9 14.0 Line Attenuation (dB) 58.0 31.5 Transmit Power (dBm) 15.5 11.9 |
|
Smith6612
MVM
join:2008-02-01
North Tonawanda, NY |
to cde
[Interleave/Fastpath] Re: Need to switch between Interleave and FastPath? Part 2You can get FastPath, yes. As per 3Mbps, most likely not. |
|
 cde
@verizon.net |
to Smith6612
Westel Versalink
Transceiver Revision: 4.3.0.1
Vendor ID Code: 4
Line Mode: G.DMT Mode
Data Path: Interleaved
Transceiver Information Down Stream Path Up Stream Path
DSL Speed (Kbits/Sec) 1792 448
Margin (dB) 13.0 21.0
Line Attenuation (dB) 53.5 31.5
Transmit Power (dBm) 15.4 11.9
Model Number D90-327W15-06
Software Version VER:4.02.00.00
Configuration 096-900125-01A
Can I get Fastpath, or atleast go up to full 3.0 speed? |
|
Smith6612
MVM
join:2008-02-01
North Tonawanda, NY ·Charter
Ubee EU2251
Ubiquiti UAP-IW-HD
Ubiquiti UniFi AP-AC-HD
|
to cisnerosc
You would quality for 7.1Mbps with possibly FastPath, however by the looks of it, you're provisioned at the 3Mbps speed, but line noise is degrading your speeds substantially. Try plugging your modem into your NID to see if the stats improve, especially the sync rate and margin before we go anywhere else. Proper sync rates are 3360 downstream, 864 upstream. With ADSL2+ which is what you're running, these numbers will be slightly less. |
|
| |
cisnerosc to Smith6612
Anon
2009-Feb-9 4:44 am
to Smith6612
Hi,
I was wondering if i could be changed to Fastpath and would i qualify for 7.1 Mbps. Here are my transtats:
Transceiver Revision: 7.2.3.0
Vendor ID Code: 4
Line Mode: ADSL2+ Mode
Data Path: Interleaved
Transceiver Information Downstream Path Upstream Path
DSL Speed (Kbits/Sec) 1280 863
Margin (dB) 7.5 11.0
Line Attenuation (dB) 38.5 23.0
Transmit Power (dBm) 17.2 12.1 |
|
Jodokast96Stupid people piss me off.
Premium Member
join:2005-11-23
NJ |
to Jurtje
Fastpath, yes, but that's it for the speed. |
|
| |
to Smith6612
Hi Smith
Could you help me with interpreting the following results? I currently have 3Mbps interleaved and I would like FastPath and maybe 7.1Mbps. Are those things possible?
Thank you
JB
Transceiver Revision: 7.2.3.0
Vendor ID Code: 4
Line Mode: ADSL2+ Mode
Data Path: Interleaved
Transceiver Information Downstream Path Upstream Path
DSL Speed (Kbits/Sec) 3355 863
Margin (dB) 13.5 10.0
Line Attenuation (dB) 51.0 28.5
Transmit Power (dBm) 17.0 12.0 |
|
Smith6612
MVM
join:2008-02-01
North Tonawanda, NY |
Plamarine, your line is good for FastPath. As per 7.1Mbps and FastPath, that is a bit iffy for me to determine that.
Giraffe42, your line is good to go. |
|
| |
to Smith6612
Transceiver Revision: 7.2.3.0
Vendor ID Code: 4
Line Mode: G.DMT Mode
Data Path: Interleaved
Transceiver Information Downstream Path Upstream Path
DSL Speed (Kbits/Sec) 3360 864
Margin (dB) 14.5 12.0
Line Attenuation (dB) 34.5 20.0
Transmit Power (dBm) 9.2 11.8
Thanks in advance! =) |
|
| |
to Smith6612
Transceiver Revision: 01.00.09.00
Vendor ID Code: 4
Line Mode: G.DMT Mode
Data Path: Interleaved
Transceiver Information Down Stream Path Up Stream Path
DSL Speed (Kbits/Sec) 3360 864
Margin (dB) 19.5 12.0
Line Attenuation (dB) 38.5 20.5
Transmit Power (dBm) 17.1 10.6
How does this look for Fastpath and 7.1? |
|
Smith6612
MVM
join:2008-02-01
North Tonawanda, NY |
to pnelsonrr
Good to go! Ask about the boost to 1Mbps/384kbps as well . It'll give you faster speeds and shave off a couple more ms to the first hop. |
|
·
