Equipment Support > Hardware By Brand > Netopia/Cayman > Netopia® 2210-02 ADSL2+ Residential Gateway

Netopia® 2210-02 ADSL2+ Residential Gateway

»broadband.motorola.com/consumers···nual.pdf

The 2210-02 is a router, and the DX-E402 is a router, so it is no wonder your PC is confused.

You really want a small switch, rather than another router.

»www.dynexproducts.com/skins/skin···nual.pdf

To demote the DX-E402 to a switch, sign in to it, »192.168.0.1 and use admin as a user id, no password. Turn off the DHCP server (page 21 of the PDF) and then connect the two routers via the LAN ports, leaving the DX-E402 WAN port empty forever. (page 7 of the PDF)
--
I tried to remain child-like, all I achieved was childish.

thank you soooooooooooooo much

reply to captCandyman
now i cant connect to xbox live?

reply to captCandyman
What is the ip address of the dx router ???

perhaps you should google port forwarding.

jimbopalmer it does not matter that the dx is a router that is not causing confusion with the netopia. unless it is having a ip collision conflict. Ie both having the same Ip address.

i would set the dx to 192.168.2.1 and that should correct any ip collisions as the netopias run on 192.168.1.254

--
† Koma †
If YOu Don't Think It's Possable!! It's Acually A Reality!!The best way to predict the future is to invent it. Alan Kay!!
Ya Don't Know The signal Till Ya Ride It!!
Voice Break's There's Trouble!!!!

Which takes al of what 30 seconds in each router.
then its done kinda set it and let its do it thing.

reply to captCandyman
i cant even open up my router page using 192.168.1.1 with the way its setup

reply to captCandyman
i set it up the way he told me to and it worked but when i connect my xbox 360 to the LAN ports my 360 fails the IP test

reply to captnCandy
X-Box 360 may require that the modem be in bridged mode.

reply to captnCandy
The Netopia/Motorola should be at 192.168.1.254 and acting as your router and default gateway.

The DX-E402 should be acting as a dumb switch, so should have no address.

If a PC is attached, it should be possible to type IPCONFIG /ALL at a command prompt to find out your actual gateway and subnet mask.
--
I tried to remain child-like, all I achieved was childish.

reply to captCandyman
»support.microsoft.com/kb/908874

»support.microsoft.com/kb/911728

read over these.

you might have to hook up to the DX router and find its wan/lan configuration and change it to 192.168.2.1 power cycle it then hook it to the netopia

other links of interest

»www2.dslreports.com/forum/remark,19473492
--
† Koma †
If YOu Don't Think It's Possable!! It's Acually A Reality!!The best way to predict the future is to invent it. Alan Kay!!
Ya Don't Know The signal Till Ya Ride It!!
Voice Break's There's Trouble!!!!

this is what it says when i go to 192.168.1.254

IP Address 76.246.199.6
IP Gateway 151.164.187.10
DNS Servers 206.13.31.12 dns1.scrmca.sbcglobal.net
68.94.157.1 dnsr2.sbcglobal.net

and at 192.168.2.1

Connection Interrupted
The connection to the server was reset while the page was loading.
The network link was interrupted while negotiating a connection. Please try again.

»broadband.motorola.com/consumers···nual.pdf

The 2210-02 is a router, and the DX-E402 is a router, so it is no wonder your PC is confused.

You really want a small switch, rather than another router.

»www.dynexproducts.com/skins/skin···nual.pdf

To demote the DX-E402 to a switch, sign in to it, »192.168.0.1 and use admin as a user id, no password. Turn off the DHCP server (page 21 of the PDF) and then connect the two routers via the LAN ports, leaving the DX-E402 WAN port empty forever. (page 7 of the PDF)

this is how i have it set up

when i type cmd /k ipconfig /all i get

Rnet NIC
ip address 76.246.199.6
subnet mask 255.255.0.0
default gateway 121.164.187.10
DHCP server 192.168.1.254
DNS servers 192.168.1.254

im not really sure what u mean
how would i reset it

reply to captCandyman
i would set the dx to 192.168.2.1 and that should correct any ip collisions as the netopias run on 192.168.1.254

thx i did that and it works now