df1sp
@sbcglobal.net | reply to GrauerFuchs
Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04
Danke - but after what?
After
127.0.0.1 &&sh /var/tmp/wr
? |
|
GrauerFuchs
join:2008-01-05 | |
|
yumagah
join:2009-10-01
Elk Grove Village, IL | reply to Phoenix2088
I unlocked my WRTP54G and tried setting it up for MJ according to the instructions, but I get no dial tone. IS there a thread somewhere for help with this setup? I can get internet thru the device so I know the hardware is working. |
|
MattNY
@rr.com | reply to Phoenix2088
Thanks for the help, got my router unlocked and am following the guide for MJ setup. |
|
MattNY
@rr.com
| reply to yumagah
I'm in the same boat as yumagah, got everything done as per instructions, double checked settings, user Id, password, etc., rebooted several times, but I still get no dial tone and can't call out. Any ideas?
Thanks very much for the screens and help here, this was a complicated project and I feel like I'm allllmost at the end  |
|
alabodi
join:2009-10-31 | Hi Folks!
I have a same symptom. I already unlocked, my Vonage WRTP54G, but no dial tone...
This is only settings failure, or maybe voice module is broken?
Please help me!
Thank you so much.. |
|
toro
join:2006-01-27
Scarborough, ON
 ·TekSavvy Solutions..
| When you look at the Info page (main page under the VoIP section) does the status of Line 1 (or Line 2, depending which one you configured) show "registered" ? What about Hook state ?
I've seen a few WRTP54G with the voice module broken, and usually the symptom was that after the port registered with the VoIP service the light corresponding to it was blinking, showing "of hook" even whn no phone was connected. |
|
meister_sd
Premium
join:2006-01-29
La Mesa, CA
| reply to alabodi
said by alabodi  :but no dial tone... This is only settings failure, or maybe voice module is broken? MagicJack has locked down pretty good the use of SIP devices on their network. Been this way for about 6 months now. Some can do outbound, some inbound, but the last I checked (a few months ago), no one got both.
Check out this site for hacking MJ, since they are dedicated to MJ only:
»www.magicjacksupport.com/ |
|
usbjtag
join:2008-10-21
Burnaby, BC
| reply to Phoenix2088
I found that MJ might have changed the way digest auth works. In stead of username:password they might add another info (call-id) maybe. I used SIPp to play what 401 reponse from MJ server but MJ generate different auth header time. So even we get user name and password we might only need to modify the device we have source for it (like asterisk). |
|
alabodi
join:2009-10-31
1 edit | reply to toro
Thank you for the answers!
This is my status page:
»i37.tinypic.com/1qlwrp.png
No matter what I am set in the VOIP setting pages, this page is nothing change..
But!
The last night, I download the NA firmware, for Vonage WRTP54g. The version number is: 1.00.??NA. This is the original FW for Vonage WRTP, but maybe modded, because SSH login is enabled..
After unlocking CYT, I logged in with dropbear, and see the VOIP logs..
Set line1, and SIP settings, and tadaaaa Line1 LED is light, and I hear dial tone.. Outgoing call is not working.
Conclusion:
1. VOIP module is working!
2. SIP settings is OK
Maybe error in the FW??
Someone could send me the ssh enabled 3.1.** modded fw for my Vonage box?
Maybe if I analyse the voice logs, found the problem..
Thank you so much! |
|
toro
join:2006-01-27
Scarborough, ON | Which of the 3.1.x firmwares are you using and who is the VoIP provider ?
I don't have the SSH enabled version but 3.1.24 works great for me. The 3.1.17 and older had a lot of problems. |
|
alabodi
join:2009-10-31 | actual fw:3.1.17
voip provider: voipdiscount.com.. But try many different provider. |
|
alabodi
join:2009-10-31
| Last night try more something..
Put this FW to my router: 3.1.27ETSI
»[Unlock] WRTP54G Unlocked firmware 3.1.27 ETSI
and 3.1.24NA..
The result is absolute same..
No VOIP, and no internet access in client machine, but receive IP from ISP, and ping is ok, in router diagnostic page..
Client computer resolve IP when I try pinging example yahoo.com, but no answer...
I don't know why do that..
So that's it.. I dont have a more idea..
I give up completely...
if someone have a working Vonage WRTP54G router FW, please send me!
Maybe help me..
Thank you..  |
|
meagin
@ameritech.net
| MagicJack may have closed down this particular hack?
I have not been messing with it for a while now. I may try the 3.1.27 firmware version. I have been using 3.1.17 and not even getting dial tone. The device does work as a router, passing thru internet to client pc's. Could be the voice module on mine is bad, since I got it used. |
|
mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| said by meagin :
The device does work as a router, passing thru internet to client pc's. Could be the voice module on mine is bad, since I got it used. Currently, what is the configurations on your router's VM? |
|
yumagah
join:2009-10-01
Elk Grove Village, IL
1 edit | (I posted the entry as "meagin".)
I followed the configuration instructions on this page:
»www.magicjacksupport.com/linksys···942.html
The config is for the RTP300 but it was the only one I could find. I think it should be very similar to the WRTP54G. |
|
Webluke
join:2009-11-30
Grand Junction, CO
| reply to Phoenix2088
I got my WRTP54G changed from 5.01.04 to 3.1.17 thanks to this and after reading a lot of 4 year old posts all over thanks for the tutorial.
Any way to a question, I can get to all the menus now except the Administration >> Firmware Upgrade / Advanced it takes me to the login screen were I have tried to put in the password I made for the box, the Admin/Admin, user/user is there something I'm missing. If you know that password send me an email at webluke (at) webluke.net or gtalk me at that same address. |
|
toro
join:2006-01-27
Scarborough, ON | Once you changed the firmware to 3.1.x, the user for the upgrade page is Admin and the password is blank.
By the way, I don't recommend using the firmware 3.1.17. You should upgrade to 3.1.24 or 3.1.27 |
|
Webluke
join:2009-11-30
Grand Junction, CO |  Ok that worked thanks toro, last night I was just happy to get it working now ill get to the latest version. |
|
yumagah
join:2009-10-01
Elk Grove Village, IL
| reply to toro
Where can I get the modified firmware version 3.1.24? I have 3.1.17 (unlocked) loaded right now, and I have downloaded the 3.1.27ETSI version that was linked to elsewhere in this forum. I also have the 3.1.24 version from the OpenWRT site, but is this version unlocked?
I just want to be sure before flashing that I am not going to brick the router. Also the unlocking process was complicated and I'd rather not repeat it if I have a choice. |
|
