Re: [Unlock] TUTORIAL: VONAGE WRTP54G WITH 5.01.04 in VOIP Tech Chat http://www.dslreports.com/forum/r21133186 en Wed, 10 Feb 2010 09:49:43 EDT Wed, 10 Feb 2010 09:49:43 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23773779 mo : anyone have the von10062.zip they can share?? Thanks]]> http://www.dslreports.com/forum/remark,23773779 Mon, 08 Feb 2010 17:03:52 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23693895 xlve : Excuse me, I speak English so terrible, forgive me. I want to ask you a question, I can not download "Von10062.zip",what size is it?
how download it in my computer?
Thanks]]> http://www.dslreports.com/forum/remark,23693895 Sun, 24 Jan 2010 09:28:51 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23686830 toro : You can't install Asterisk on the WRTP54G but you can use the ATA inside the WRTP54G to connect to an external Asterisk box (or another VoIP service).]]> http://www.dslreports.com/forum/remark,23686830 Fri, 22 Jan 2010 15:15:17 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23686645 anon : OK, I am leaving Vonage soon. I have a WRTP54G. When I leave Vonage and then unlock my device, will this router allow me to set up and run asterisk? How can I find out what my h/w options are for getting asterisk set up? Are there any demo sites or videos that demonstrate what fun lies ahead by having my device unlocked? ]]> http://www.dslreports.com/forum/remark,23686645 Fri, 22 Jan 2010 14:56:46 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23663151 toro : Yes, it's the correct thread and has the unlocking method for both RT31P2 (non wireless) and the wireless "cousin" WRT54GP2]]> http://www.dslreports.com/forum/remark,23663151 Mon, 18 Jan 2010 17:34:24 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23663127 truasian16 : thanks I will check out that thread is the rtp31p2 the same as the wrtp54gp2 i saw some pics and the board looks the same just wondering what files i should use don't want to use the wrong ones]]> http://www.dslreports.com/forum/remark,23663127 Mon, 18 Jan 2010 17:30:04 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23661806 toro :
said by truasian16 See Profile :

Firmware Version: 1.30.01
Setup

Wireless-G Broadband Router with 2 Phone Ports WRT54GP2

thats what it says and its 3 lan ports one antenna and two phone ports and 1 wan port
OK, that's an entirely different router. Initially you said WRTP54G v2, which does exist but it's not popular at all.
For unlocking info on WRT54GP2, see the »RT31P2 Unlock thoughts?? thread]]> http://www.dslreports.com/forum/remark,23661806 Mon, 18 Jan 2010 13:15:37 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23661753 truasian16 : Firmware Version: 1.30.01
Setup

Wireless-G Broadband Router with 2 Phone Ports WRT54GP2

thats what it says and its 3 lan ports one antenna and two phone ports and 1 wan port]]> http://www.dslreports.com/forum/remark,23661753 Mon, 18 Jan 2010 13:05:28 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23660390 toro : Also, are you sure the firmware is 1.30 and not 0.30 ?]]> http://www.dslreports.com/forum/remark,23660390 Mon, 18 Jan 2010 07:04:52 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23660388 toro : Is this a WRTP54G-ST ? Mine had the Admin's password blank after a factory reset. Obviously you need to login as admin/admin first.]]> http://www.dslreports.com/forum/remark,23660388 Mon, 18 Jan 2010 07:04:02 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23660091 truasian16 : i have a wrtp54g v2 is it still possible to unlock this device? the fw is 1.30 and i can't get into the voice tab]]> http://www.dslreports.com/forum/remark,23660091 Mon, 18 Jan 2010 01:34:34 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23653867 mrush22 : My problem was my dsl was not working correctly, and it took me a while to figure that out. Only certain things would download and others would not. Called tech support and they solved my problem. After that I followed the instructions on page 1 and had no problems other then hex editing the file which I don't think u need. Follow the instructions on page 1 and make sure ur firewall is disabled and u should be good to go good luck.]]> http://www.dslreports.com/forum/remark,23653867 Sat, 16 Jan 2010 15:47:28 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23653539 Dudemellow : Hi, I have a Vonage WRTP54g (5.01.04) and I am having trouble downgrading to firmware 1.00.62. Everything seems fine up until about 93% of the upload then it starts a snails pace for about 7-8 min. It completes but nothing happens. I saw someone with the same issue earlier in the post. I have confirmed that the wireless is disabled every time I attempt but still end with the same results.
Any suggestions? ]]> http://www.dslreports.com/forum/remark,23653539 Sat, 16 Jan 2010 14:14:24 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23624613 Chris100 : Thanks for your quick response. :)]]> http://www.dslreports.com/forum/remark,23624613 Mon, 11 Jan 2010 12:50:47 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23624559 toro :
said by Chris100 See Profile :

Hello everyone great post :)
I still haven't put this unit online yet I am wondering if I need to do more.
After reading about the auto provisioning I am kinda wary.
I did reset as instructed on page one. However I did not do the ping thing.
If you already upgraded the firmware from 1.00.xx to 3.1.24 you don't need to worry about anything else. Your router is now free of Vonage and you can connect it to the Internet and start using it with another VoIP company.]]> http://www.dslreports.com/forum/remark,23624559 Mon, 11 Jan 2010 12:41:09 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23624408 Chris100 : Hello everyone great post :)
I have RTP300 which had 1.01.07 on it I used CYT 3.5 to put 3.1.24 firmware . I did the hex edit (thanks that brought back memories of xtree in the old days).
I still haven't put this unit online yet I am wondering if I need to do more.

After reading about the auto provisioning I am kinda wary.
I did reset as instructed on page one. However I did not do the ping thing.

Should I try get any code off the unit before I go live so to speak if I haven't unlocked it properly will it brick?

I just wish to recycle the unit for use as an ATA with another provider.]]> http://www.dslreports.com/forum/remark,23624408 Mon, 11 Jan 2010 12:20:39 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23617702 truasian16 : tried that but figured out the password is blank and the user is Admin i got it from page 7 of this topic

what is the most stable firmware I should be using for voice options for the RTP 300

thanks the topic is great i got a brick working lol

btw why doesn't cyt work on this shouldn;t it work on the router? i been runnig it for the past 10 minutes over and over and still nothing

I think this is what I have to do I think i have a vonage rpt300
because I tried flashing the orginal firmware to the router and it says invalid before I brick it I wanted to make sure if someone in here has done what i have listed below and it works good for them thanks

aslo if someone has done it and still has the fw handy can you pm thanks

* note: use a HEX editor to make these changes.

1. Download the RTP300 3.1.24 firmware from the linksys site (link in previous msg)

2. Open the file in your HexEditor and change offset 0x17 from 4D to 4C.

3. At offset 0x3B0004, change 85 DA 20 BB to 3B A5 4D DA

4. Done!

MD5 checksums are as follows:

a430df5109cefc8daaa8ef97720fb3b1 rtp300_fw_3.1.24_US.img
b15b248145a48e745afd5003c88eee17 rtp300_von_3.1.24_US.img]]> http://www.dslreports.com/forum/remark,23617702 Sat, 09 Jan 2010 21:43:06 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23617610 toro : Have you tried holding the reset button for about 8 seconds (until the lights start flashing) ?]]> http://www.dslreports.com/forum/remark,23617610 Sat, 09 Jan 2010 21:22:07 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23617551 truasian16 : I have Firmware Version: 3.1.24 on Broadband Router RTP300
and my issue is the password I cannot update the firmware without the username and password and I reset the router as well Anyone know what else I could do to set everything back to factory maybe a menupage somewhere that I haven't seen. I can get in the router with admin/admin then I am stuck at the adminstration page

i used this link »forum.voip.com/topic/776/how-to-···rovider/

and now I cannot reset the password has anyone used this link in the past?

tried that but figured out the password is blank and the user is Admin i got it from page 7 of this post now what is the most stable firmware I should be using for voice options for the RTP 300]]> http://www.dslreports.com/forum/remark,23617551 Sat, 09 Jan 2010 21:04:36 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23583228 mrush22 : Finally figured out my problem, my dsl was not allowing me to download. Called tech support technician came out put me on new dsl port, downloaded file did firmware changes and now enjoying free phone with google voice and sipgate. Thanks everyone for a nice informative thread]]> http://www.dslreports.com/forum/remark,23583228 Sun, 03 Jan 2010 18:27:27 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23582685 anon : so does this mj on rtp300 still work? I been fighting with it for a few day's now then i notice all the post's were pretty old..

if it does could someone point me to a good tutorial, I have the rtp300 unlocked and i have my name and pw for mj just having problems with all the other settings..

thanks in advance]]> http://www.dslreports.com/forum/remark,23582685 Sun, 03 Jan 2010 16:08:08 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23562313 chpalmer : No problem. I hate being beat by this stuff... :D

Last thing... no firewall?

Good Luck!]]> http://www.dslreports.com/forum/remark,23562313 Tue, 29 Dec 2009 21:51:45 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23562257 mrush22 : Thanks for the help chpalmer I've done the factory reset. I've gotten the console unlocked,but for some reason I can't get the firmware to load or download one or the other. I'll keep trying. Hopefully I'll get it eventually thanks again for the help]]> http://www.dslreports.com/forum/remark,23562257 Tue, 29 Dec 2009 21:38:26 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23561719 chpalmer : I loaded the vonage 5.0 firmware back on this thing to see what would happen. Of course in relocked but worth a try...

Ive reunlocked it now.

mrush22
- Did you do a factory reset first? ]]> http://www.dslreports.com/forum/remark,23561719 Tue, 29 Dec 2009 19:43:49 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23559022 mrush22 : Thanks alot for ur quick reply. Im still having problems loading the firmware from the instructions on page 1. The file transfers from the tftp server but router never reboots. I've also tried the instructions on page 6 of the thread with the rtp300_txt file and try to download from von server, the router does reboot but the file is not there Im stumped. I know Im technically challenged but I do have a ubuntu server shared with windows computers and I can't figure this out for nothing. Thanks in advanced.]]> http://www.dslreports.com/forum/remark,23559022 Tue, 29 Dec 2009 11:31:18 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23557475 chpalmer : Dont try to hexedit that firmware. The 1.0.62 firmware is vonage for the rtp.

Just put it on the tftp server and make sure your tftp server is on the computer with the lan address 192.168.15.100

Take the instructions on the first page one line at a time.]]> http://www.dslreports.com/forum/remark,23557475 Tue, 29 Dec 2009 01:00:57 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23556637 mrush22 : Hello All
I just purchased a rtp300 router and have read this whole thread and am having problems unlocking my router. I think I have it down to the hex editing, which I can't seem to figure out so I can't load the von10062.bin and downgrade my firmware. If anyone can help it would be greatly appericated I been trying to unlock this router for 3 days thanks. Also after downgrading firmware what do I upgrade to. Thanks]]> http://www.dslreports.com/forum/remark,23556637 Mon, 28 Dec 2009 21:23:59 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23552393 macman4hire : Here is some interesting info on Comfort Noise Generator.»searchtelecom.techtarget.com/sDe···,00.html]]> http://www.dslreports.com/forum/remark,23552393 Sun, 27 Dec 2009 23:31:50 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23552365 chpalmer : Can the WRT firmware be used on an RTP? With mods?]]> http://www.dslreports.com/forum/remark,23552365 Sun, 27 Dec 2009 23:25:21 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23552339 chpalmer : Ive got the modded version of 3.1.24- Thanks! :)

My belief at this point is that the switch does not work to control it.

Ive seen other posts that support that. If I can find the switch while consoled in then I will try that.

Anyone got 3.1.27 yet? ]]> http://www.dslreports.com/forum/remark,23552339 Sun, 27 Dec 2009 23:18:28 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23552281 macman4hire : chpalmer - I cannot perceive any difference in the noise level between line 1 with the Comfort Noise Generation: switch off and line 2 with the Comfort Noise Generation: switch on. This elavaution is based the noise during the ring tone on the same speaker using a different line.]]> http://www.dslreports.com/forum/remark,23552281 Sun, 27 Dec 2009 23:04:50 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23552272 macman4hire : chpalmer- I just turned my Comfort Noise Generation: switch off on my RTP300. I have 3.1.24 modified version of the firmware. If you want to try the copy I have PM with your email and I will send you a copy.]]> http://www.dslreports.com/forum/remark,23552272 Sun, 27 Dec 2009 23:00:43 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23552227 chpalmer :
said by macman4hire See Profile :

What negative behavior does the Comfort Noise Generation: switch have when turned on?
Its the same. White noise on the line. Unfortunately Its a bit loud on my particular phones. Especially the speaker phone.

Ill get over it but would be nice to have a fix. ]]> http://www.dslreports.com/forum/remark,23552227 Sun, 27 Dec 2009 22:52:14 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23552219 chpalmer :
said by mazilo See Profile :

Have you tried a factory reset to see if this problem can be resolved?
Yep.. Im looking around to see if I can try a free provider just to try it... To rule out the provider.

This thing worked flawlessly under Vonage up till it turned into a project b a port out... :D

Quick side question... I cant seem to generate a correct checksum with Hexworkshop 5... Any hints?]]> http://www.dslreports.com/forum/remark,23552219 Sun, 27 Dec 2009 22:49:53 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23552199 macman4hire : What negative behavior does the Comfort Noise Generation: switch have when turned on?]]> http://www.dslreports.com/forum/remark,23552199 Sun, 27 Dec 2009 22:44:29 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23552162 mazilo :
said by chpalmer See Profile :

Comfort Noise Generation:
IC. Thanks.

Mine seems to be switched on and I cant get it off. Im wondering if the provider has anything to do with it...
Have you tried a factory reset to see if this problem can be resolved?
--
Mazilo always prays for FREEBIES!
UK Phone: +44-703-194-2574
]]> http://www.dslreports.com/forum/remark,23552162 Sun, 27 Dec 2009 22:35:37 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23551920 chpalmer :
Comfort Noise Generation:

Seems the switch was added on the "Line" pages sometime after 3.1.10...

Mine seems to be switched on and I cant get it off. Im wondering if the provider has anything to do with it...]]> http://www.dslreports.com/forum/remark,23551920 Sun, 27 Dec 2009 21:36:48 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23551826 mazilo :
said by chpalmer See Profile :

Im having trouble getting the hiss generator to shut off.
What is a hiss generator?]]> http://www.dslreports.com/forum/remark,23551826 Sun, 27 Dec 2009 21:12:10 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23551748 chpalmer : Has anyone tried reloading the 5.01.04 firmware back after unlocking their RTP300?

Im having trouble getting the hiss generator to shut off.

Ive tried 3.1.10 and am running 3.1.24 right now.

None of our Vonage provisioned boxes have or have had this problem...

The 4 port switch on mine also has the problem connecting that many others seem to have also. I notice if I plug in two computers then the problem goes away sometimes. Forcing to connect at 10mbps works I hear. Have not tried.]]> http://www.dslreports.com/forum/remark,23551748 Sun, 27 Dec 2009 20:52:41 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23476928 toro :
said by truasian16 See Profile :

i just got my hands on a Linksys WRTP54G with firmware 3.1.2_0.3.5
I've never seen the firmware version in that format, but usually the 3.x are the ones made for Earthlink. If that's the case, the Voice tab under the router's web interface should take you to the actual VoIP settings page, instead of the "contact your Voip company for more options" page.
There's another thread with lots of info about unlocking the Earthlink router: »[WRTP54G-ER] How to unlock and re-use this earthlink device.]]> http://www.dslreports.com/forum/remark,23476928 Fri, 11 Dec 2009 21:39:10 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23474078 truasian16 : i just got my hands on a Linksys WRTP54G with firmware 3.1.2_0.3.5

is it possible to unlock it easily or is it not possible ]]> http://www.dslreports.com/forum/remark,23474078 Fri, 11 Dec 2009 12:11:08 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23463585 anon : Tomorrow I gonna buy Linksys RTP300 from Craigslist and I can't check it, so my question is: Can I unlock it by myself? If I will folow instruction from first page?
Is it really matter about firmware? What a latest firmware I can unck it?

Thank you dudes!]]> http://www.dslreports.com/forum/remark,23463585 Wed, 09 Dec 2009 16:07:51 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23444142 toro : What VoIP provider are you using ? Have you tried more than one ? Some companies like Callcentric offer free accounts (and even show in their web portal if your adapter is registered) you may want to try one of those just to check if your router functions properly.]]> http://www.dslreports.com/forum/remark,23444142 Sat, 05 Dec 2009 21:24:57 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23443652 yumagah : The D-Link Router was seeing the WRTP and assigning it an address ok. Everything else was as you say it should be. I plugged the WRTP directly into the D-Link router, and still got Registration:Failed and no dial tone. Starting to look like a hardware problem with the voip module. It functions ok as a 10mbp switch, router and WAP, so I wonder.

One possible question: There are a few setting that are different on the screen shots vs the text .config file, in the forum where setup is described. Wondering if any of those would make a difference.]]> http://www.dslreports.com/forum/remark,23443652 Sat, 05 Dec 2009 18:35:51 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23440361 toro : I don't see any problem with your setup as long as the DD-WRT doesn't do any kind of NATing on its own (in other words your DD-WRT's LAN ports are bridged directly to the LAN of the neigbor's router). Also you should have turned off the DHCP server in your DD-WRT router and use it the DHCP from the neigbor's router.
Now about your WRTP: the NAT router feature should be turned on (it is on by default), and the DHCP should also be turned on. In the VoIP configuration, because it's connected behind another NAT router, you should activate the NAT Mapping and NAT Keepalive under each of the Line 1 and Line 2 ports. Also you should set up a STUN server under the SIP tab and probably enable most of the options under the NAT Support Parameters.]]> http://www.dslreports.com/forum/remark,23440361 Fri, 04 Dec 2009 21:13:41 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23440330 yumagah : My network setup is rather "kludgy". I receive a wifi signal from a D-Link router, in a neighboring building. The receiver is a WRT54g running dd-wrt in repeater bridge mode. Wireless interference is occasionally a problem. When that happens I connect my pc's to the WRT54g(dd-wrt) via ethernet cable and get a better connection.

I have been connecting the Internet port (blue) on the WRTP54g to the dd-wrt bridge via ethernet. So the WRTP is behind both the D-link router and the repeater bridge. I am thinking this is at least part of the problem.
Next step to test is plug the WRTP directly into the D-Link router. ]]> http://www.dslreports.com/forum/remark,23440330 Fri, 04 Dec 2009 21:01:54 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23432881 toro : You said your WRTP54G is behind another router. How is it connected to that router, through the WAN port or through one of the LANs ? The VoIP module of the WRTP54G can only work if the router is connected to the Internet through WAN.
Also, if you connect it to the other router through the WAN, there's no point in disabling the DHCP on the WRTP54G. Also, you should not disable NAT on the WRTP54G.
However, my preference is to connect the VoIP router immediately after the modem and any other router behind it.]]> http://www.dslreports.com/forum/remark,23432881 Thu, 03 Dec 2009 13:34:07 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23432741 yumagah : I upgraded to 3.1.27ETSI, left all settings as they were, and still no dial tone or provisioning. And this time the WRTP54g won't even act as a router like it did before. The hardware lights show a connection but the devices act as if there was none. I can connect directly to the WRTP54g from my PC so I don't think it's a hardware issue. (tho it does have a small problem with the ethernet ports, requiring me to connect at 10mpbs.)

I tried disabling DHCP because it is behind a wireless router and bridge, no difference. I tried setting up a DMZ on the router with the IP address of the WRTP54g, no difference.

My network architecture may be too complex for this? I will try seting this up on another network and see.]]> http://www.dslreports.com/forum/remark,23432741 Thu, 03 Dec 2009 13:08:34 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23430882 toro : Modify the firmware 3.1.24 for the -NA routers as described here »Re: New WRTP54G-NA firmware 3.1.24 released 3-27-07 to load on a Vonage router.
Don't worry, as long as your router is on any of the 3.1.x firmwares, it can't get locked to Vonage]]> http://www.dslreports.com/forum/remark,23430882 Thu, 03 Dec 2009 07:08:51 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23429562 yumagah : Where can I get the modified firmware version 3.1.24? I have 3.1.17 (unlocked) loaded right now, and I have downloaded the 3.1.27ETSI version that was linked to elsewhere in this forum. I also have the 3.1.24 version from the OpenWRT site, but is this version unlocked?

I just want to be sure before flashing that I am not going to brick the router. Also the unlocking process was complicated and I'd rather not repeat it if I have a choice.]]> http://www.dslreports.com/forum/remark,23429562 Wed, 02 Dec 2009 22:54:39 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23414236 Webluke : Ok that worked thanks toro, last night I was just happy to get it working now ill get to the latest version.]]> http://www.dslreports.com/forum/remark,23414236 Mon, 30 Nov 2009 12:53:58 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23413076 toro : Once you changed the firmware to 3.1.x, the user for the upgrade page is Admin and the password is blank.
By the way, I don't recommend using the firmware 3.1.17. You should upgrade to 3.1.24 or 3.1.27]]> http://www.dslreports.com/forum/remark,23413076 Mon, 30 Nov 2009 09:19:33 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23412637 Webluke : I got my WRTP54G changed from 5.01.04 to 3.1.17 thanks to this and after reading a lot of 4 year old posts all over thanks for the tutorial.

Any way to a question, I can get to all the menus now except the Administration >> Firmware Upgrade / Advanced it takes me to the login screen were I have tried to put in the password I made for the box, the Admin/Admin, user/user is there something I'm missing. If you know that password send me an email at webluke (at) webluke.net or gtalk me at that same address. ]]> http://www.dslreports.com/forum/remark,23412637 Mon, 30 Nov 2009 06:17:02 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23330630 yumagah : (I posted the entry as "meagin".)

I followed the configuration instructions on this page:
»www.magicjacksupport.com/linksys···942.html

The config is for the RTP300 but it was the only one I could find. I think it should be very similar to the WRTP54G.]]> http://www.dslreports.com/forum/remark,23330630 Thu, 12 Nov 2009 11:28:35 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23325369 mazilo :
said by meagin :

The device does work as a router, passing thru internet to client pc's. Could be the voice module on mine is bad, since I got it used.
Currently, what is the configurations on your router's VM?]]> http://www.dslreports.com/forum/remark,23325369 Wed, 11 Nov 2009 11:52:32 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23325215 anon : MagicJack may have closed down this particular hack?

I have not been messing with it for a while now. I may try the 3.1.27 firmware version. I have been using 3.1.17 and not even getting dial tone. The device does work as a router, passing thru internet to client pc's. Could be the voice module on mine is bad, since I got it used.]]> http://www.dslreports.com/forum/remark,23325215 Wed, 11 Nov 2009 11:51:07 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23324036 alabodi : Last night try more something..

Put this FW to my router: 3.1.27ETSI

»[Unlock] WRTP54G Unlocked firmware 3.1.27 ETSI

and 3.1.24NA..

The result is absolute same..
No VOIP, and no internet access in client machine, but receive IP from ISP, and ping is ok, in router diagnostic page..

Client computer resolve IP when I try pinging example yahoo.com, but no answer...
I don't know why do that..

So that's it.. I dont have a more idea..
I give up completely...

if someone have a working Vonage WRTP54G router FW, please send me!
Maybe help me..

Thank you.. :huh:]]> http://www.dslreports.com/forum/remark,23324036 Wed, 11 Nov 2009 04:49:04 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23320571 alabodi : actual fw:3.1.17
voip provider: voipdiscount.com.. But try many different provider.]]> http://www.dslreports.com/forum/remark,23320571 Tue, 10 Nov 2009 13:37:30 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23320018 toro : Which of the 3.1.x firmwares are you using and who is the VoIP provider ?
I don't have the SSH enabled version but 3.1.24 works great for me. The 3.1.17 and older had a lot of problems.]]> http://www.dslreports.com/forum/remark,23320018 Tue, 10 Nov 2009 12:00:01 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23318442 alabodi : Thank you for the answers!

This is my status page:
»i37.tinypic.com/1qlwrp.png

No matter what I am set in the VOIP setting pages, this page is nothing change..

But!
The last night, I download the NA firmware, for Vonage WRTP54g. The version number is: 1.00.??NA. This is the original FW for Vonage WRTP, but maybe modded, because SSH login is enabled..
After unlocking CYT, I logged in with dropbear, and see the VOIP logs..
Set line1, and SIP settings, and tadaaaa Line1 LED is light, and I hear dial tone.. Outgoing call is not working.

Conclusion:
1. VOIP module is working!
2. SIP settings is OK

Maybe error in the FW??

Someone could send me the ssh enabled 3.1.** modded fw for my Vonage box?
Maybe if I analyse the voice logs, found the problem..

Thank you so much!]]> http://www.dslreports.com/forum/remark,23318442 Tue, 10 Nov 2009 03:49:04 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23316691 usbjtag : I found that MJ might have changed the way digest auth works. In stead of username:password they might add another info (call-id) maybe. I used SIPp to play what 401 reponse from MJ server but MJ generate different auth header time. So even we get user name and password we might only need to modify the device we have source for it (like asterisk).]]> http://www.dslreports.com/forum/remark,23316691 Mon, 09 Nov 2009 19:17:01 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23316050 meister_sd :
said by alabodi See Profile :

but no dial tone...
This is only settings failure, or maybe voice module is broken?
MagicJack has locked down pretty good the use of SIP devices on their network. Been this way for about 6 months now. Some can do outbound, some inbound, but the last I checked (a few months ago), no one got both.

Check out this site for hacking MJ, since they are dedicated to MJ only:

»www.magicjacksupport.com/]]> http://www.dslreports.com/forum/remark,23316050 Mon, 09 Nov 2009 17:09:51 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23315678 toro : When you look at the Info page (main page under the VoIP section) does the status of Line 1 (or Line 2, depending which one you configured) show "registered" ? What about Hook state ?
I've seen a few WRTP54G with the voice module broken, and usually the symptom was that after the port registered with the VoIP service the light corresponding to it was blinking, showing "of hook" even whn no phone was connected.]]> http://www.dslreports.com/forum/remark,23315678 Mon, 09 Nov 2009 16:06:32 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23313003 alabodi : Hi Folks!

I have a same symptom. I already unlocked, my Vonage WRTP54G, but no dial tone...
This is only settings failure, or maybe voice module is broken?

Please help me!

Thank you so much..]]> http://www.dslreports.com/forum/remark,23313003 Mon, 09 Nov 2009 03:34:01 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23282562 anon : I'm in the same boat as yumagah, got everything done as per instructions, double checked settings, user Id, password, etc., rebooted several times, but I still get no dial tone and can't call out. Any ideas?

Thanks very much for the screens and help here, this was a complicated project and I feel like I'm allllmost at the end :)]]> http://www.dslreports.com/forum/remark,23282562 Tue, 03 Nov 2009 00:51:32 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23282313 anon : Thanks for the help, got my router unlocked and am following the guide for MJ setup.]]> http://www.dslreports.com/forum/remark,23282313 Mon, 02 Nov 2009 23:43:20 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23274159 yumagah : I unlocked my WRTP54G and tried setting it up for MJ according to the instructions, but I get no dial tone. IS there a thread somewhere for help with this setup? I can get internet thru the device so I know the hardware is working.]]> http://www.dslreports.com/forum/remark,23274159 Sun, 01 Nov 2009 10:39:42 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23201929 GrauerFuchs : ]]> http://www.dslreports.com/forum/remark,23201929 Sun, 18 Oct 2009 07:59:37 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23201106 anon : Danke - but after what?
After
127.0.0.1 &&sh /var/tmp/wr
?]]> http://www.dslreports.com/forum/remark,23201106 Sat, 17 Oct 2009 22:52:21 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23201007 GrauerFuchs : Try a single ampersand and a space after it.]]> http://www.dslreports.com/forum/remark,23201007 Sat, 17 Oct 2009 22:21:48 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23200907 anon : Hi, I have a WRTP-54G, Firmware 1.00.18
After the last step of Phase 1 (unlock), I do not get the "promised relief".....Console_State unlocked

Rather,
here is the response:
PING 127.0.0.1 &&sh /var/tmp/wr (127.0.0.1): 64 data bytes 72 bytes from 127.0.0.1: icmp_seq=0 ttl=255 time=0.0 ms 72 bytes from 127.0.0.1: icmp_seq=1 ttl=255 time=0.0 ms 72 bytes from 127.0.0.1: icmp_seq=2 ttl=255 time=0.0 ms 72 bytes from 127.0.0.1: icmp_seq=3 ttl=255 time=0.0 ms 72 bytes from 127.0.0.1: icmp_seq=4 ttl=255 time=0.0 ms --- 127.0.0.1 &&sh /var/tmp/wr ping statistics --- 5 packets transmitted, 5 packets received, 0% packet loss round-trip min/avg/max = 0.0/0.0/0.0 ms

Any idea anyone what might have happened?
I followed everything....
Thanks - ]]> http://www.dslreports.com/forum/remark,23200907 Sat, 17 Oct 2009 22:14:41 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23154085 dynavoip :
Hello! thank in advance all the help it can get from you, I have a linksys RTP300 and have no access to VOICE, is blocked by Vonage, I have followed all the steps above before mentioned but I'm not getting results, obviously something I'm failing, but not in which, perhaps may be in the last file and not edit it with the hex editor, I have not found that RTP300 I transfer files to and not because I have all files in TFTPD32 and TFTP32 works fine, now when I go 192.168.15.1/update.html enter a password I do not work or admin / admin or admin / admin or user / admin that is to say no, besides if I enter the Admin when I go to be alone again; would be kind enough to collaborate with the steps a little more detailed and the files to use, given that am only new to this.
thanks for the help.
danilo]]> http://www.dslreports.com/forum/remark,23154085 Thu, 08 Oct 2009 18:55:05 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23097902 anon : hi Phoenix2088
i have to try unlock my rtp 300, my firmware is 1.00.62 right now :), but i can´t modify the img file with hex editor :huh:, do you have a modified RTP300 NA firmware, thanks a lot]]> http://www.dslreports.com/forum/remark,23097902 Mon, 28 Sep 2009 21:35:19 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23073947 GrauerFuchs :
said by gaugevox See Profile :

I realized Firefox was automatically switching my captial A to a lowercase. I had to switch over to internet explorer to preserve the case of my username and password. Once I did it was a breeze. Just thought I'd share that in case anyone ran into the same problem.
I may be wrong here, but it sounds like it's trying to fill things in from the password caching service in Firefox. If so, it might happen in other browsers as well. Either way, thank you for pointing out the potential trouble. It could save many users a boatload of grief when trying to get things working again.]]> http://www.dslreports.com/forum/remark,23073947 Thu, 24 Sep 2009 06:17:35 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23073480 mazilo :
said by gaugevox See Profile :

I realized Firefox was automatically switching my captial A to a lowercase.
Interesting! I never encountered this problem with a Firefox on my Linux machine.]]> http://www.dslreports.com/forum/remark,23073480 Thu, 24 Sep 2009 00:46:02 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,23073316 gaugevox : First off, thank you all for the helpful information. I just bought an RTP300 and was not aware that it was Vonage-locked one. Following the steps in this forum I have succesfully gotten from Version 5.1.04 to 3.1.22. I thought I'd post a little tip about something that tripped me up for a while. After I had unlocked the router and reset admin passwords using CYT, I could do the initial admin/admin login, but not the Admin/Admin login on the update.html page. I realized Firefox was automatically switching my captial A to a lowercase. I had to switch over to internet explorer to preserve the case of my username and password. Once I did it was a breeze. Just thought I'd share that in case anyone ran into the same problem. ]]> http://www.dslreports.com/forum/remark,23073316 Wed, 23 Sep 2009 23:59:12 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22829012 Antman : yes. I used "Stroths MagicJack Utilities Suite" and it got the info for me and placed it in a text file for me. ]]> http://www.dslreports.com/forum/remark,22829012 Fri, 07 Aug 2009 00:40:14 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22828985 mazilo :
said by Antman See Profile :

I can confirm it works.
Did you use stroth's method to get the SIP credentials of your MJ?]]> http://www.dslreports.com/forum/remark,22828985 Fri, 07 Aug 2009 00:30:23 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22828917 Antman : I can confirm it works. I havent had too many issues. I am thinking my RPT300 is having issues though cause it has a noise I can hear when it is plugged in and locks up sometimes when calling people without 1 plus the area code. Follow that guide and make it all look like those pics and it works. Good Luck with it.]]> http://www.dslreports.com/forum/remark,22828917 Fri, 07 Aug 2009 00:10:38 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22828125 mazilo :
said by Antman See Profile :

here is the guide I found for configuring the MagicJack settings: »www.magicjacksupport.com/linksys···942.html
From what I read the post on the above link, it appeared getting an MJ to work on an ATA is back to business. Can anyone confirm this?]]> http://www.dslreports.com/forum/remark,22828125 Thu, 06 Aug 2009 21:13:37 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22828032 Antman : here is the guide I found for configuring the MagicJack settings: »www.magicjacksupport.com/linksys···942.html

My only issues I am having so far is that if I dont put 1 plus the area code in the RPT300 locks up like the phone is off the hook and no matter what I do it acts like the phone is off the hook. I have to power cycle the router and wait for it to link back up. Magic jack makes me have to put the 1 plus the area code in for every call I do.

Also I am noticing with the RPT300 there is a kinda high pitch noise that come from it sometimes and a click when I pave the phone off the hook or when I put it back on the hook. Is this normal?]]> http://www.dslreports.com/forum/remark,22828032 Thu, 06 Aug 2009 20:57:05 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22822822 GrauerFuchs : It is intended to support full 100mbit, but 100mbit requires signaling on more lines than 10mbit. If one of the traces is poor or the chip is flaky, it may lose that signal or have problems with the data transfer.]]> http://www.dslreports.com/forum/remark,22822822 Thu, 06 Aug 2009 00:24:49 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22819267 anon : After reading the post by Kavalco, I hooked up an old 10mbit hub in between, and that seems to have solved the problem with the ethernet ports. I wonder if this thing was meant to support 100mbit, or is it just a hardware problem on mine?

Antman, can you tell me how to set it up with Magicjack? Or show me where is the FAQ on that?]]> http://www.dslreports.com/forum/remark,22819267 Wed, 05 Aug 2009 13:09:11 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22806110 Antman : I have a RTP300 and have been following the tutorial exatcly as it shows and have downloaded the RTP firmware from Linksys then hexedited it but I never get that far. I do the commands and see the File get downloaded by the router the file "von10062.bin" goes to it then nothing happens. the power light never starts flashing it just never reflashes the router at all. What can I try? I really want to ge this thing unlocked.

**EDIT**
I wanted to add that I did get it done. I didnt rename the img file I downloaded for the RPT300 to von10062.bin. I renamed it then did the steps again and it worked. i then ran cyt35.exe and it did its thing then I was able to upgrade to my hex edited image file I got from the linksys web site and now I am unlocked. I set it up with MagicJack and all is good. Only issue I get sometimes is the adapter sometimes thinks my phone stays off the hook when I do a phone call. But I really appreciate this guide. Thank you to all that made it possible. Vonage told me that since I didnt have Vonage I should either send them back the router or throw it away. LOL! The guy told me if I didnt get Vonage service it wouldnt even function as a router.]]> http://www.dslreports.com/forum/remark,22806110 Mon, 03 Aug 2009 09:58:18 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22800507 anon : My router have the same problem, the ethernets ports cutting on and off. Them i force the ethernet port of my computer to 10 mbps full duplex and.... the ports up!!!]]> http://www.dslreports.com/forum/remark,22800507 Sat, 01 Aug 2009 20:38:27 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22785581 anon : Okay. after a few tries I unlocked it. I now have a WRTP54G with 3.1.17 firmware, and I can change setting under the Voice tab. Now will someone here kindly point me to the FAQ or document I need to see what I can do with it?]]> http://www.dslreports.com/forum/remark,22785581 Wed, 29 Jul 2009 18:30:43 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22784210 anon : I cant for the life of me get my rtp300 to work with my wrt54g and gizmo5 anyone care to help?]]> http://www.dslreports.com/forum/remark,22784210 Wed, 29 Jul 2009 13:43:23 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22783656 anon : Taking a hint from other posts here, I have found that plugging in 2 or more devices to ethernet ports gives somewhat better connections. Probably a bad solder connection. Gonna try unlocking this thing, not much to lose.

There is a chain of resale shops in my area run by Goodwill Industries. I check them regularly for used networking junk. I got lucky this time but there is no predicting what will be there on any given day.]]> http://www.dslreports.com/forum/remark,22783656 Wed, 29 Jul 2009 12:30:57 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22782681 mazilo :
said by yumagah :

I just got a WRTP54G from a resale shop for $5.
Which resale shop did you get this WRTP54G for $5? I will be more than happy to get some units.]]> http://www.dslreports.com/forum/remark,22782681 Wed, 29 Jul 2009 09:01:17 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22782369 GrauerFuchs : It sounds like it's either overheating (check the voltage output from the power supply and see how far off 12V it really is) or that you have a bad solder joint on the board.
If the wireless and internet never drop out even when ethernet does, it's most likely a bad solder joint.]]> http://www.dslreports.com/forum/remark,22782369 Wed, 29 Jul 2009 06:19:36 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22781800 anon : I just got a WRTP54G from a resale shop for $5. I figured it was something to play with but now I'm curious. It has 1.00.62 firmware on it, and I can login as admin/admin. But it has the same problem with the ethernet ports cutting on and off. The Internet port and wireless work ok. Ethernet ports are normal until it warms up, then no good. I have another 12v power supply I can try, and I can try fanning it or ice cubes in baggies. So far it works good as a wifi acccess point. Plugging in a phone gets a message about checking my account status. I have a Magicjack already so maybe it's worth messing around with.]]> http://www.dslreports.com/forum/remark,22781800 Wed, 29 Jul 2009 00:11:09 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22776334 mach5 : Wirelessrat, would you please point me to the right direction where I can download rpt300 3.1.24 firmware. I haven't uses rpt300 over a year and is at firmware (vonage) 1.00.62. I did step #5 on page 1 of this thread and just need to load new firmware.

Thanks.

Btw, how is 3.1.24 working out for you?]]> http://www.dslreports.com/forum/remark,22776334 Tue, 28 Jul 2009 02:59:38 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22770886 anon : My question is... Once I do all this changing to the router, how do I get a and use the phone number or do I even get one? Or is it better just to purchase the majick jack? Newbie]]> http://www.dslreports.com/forum/remark,22770886 Mon, 27 Jul 2009 02:02:10 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22770415 petey_ : I have the same exact problem with my RTP300. Soo annoying.]]> http://www.dslreports.com/forum/remark,22770415 Sun, 26 Jul 2009 23:10:53 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22732116 GrauerFuchs : Did you use the same power adapter with both? I've seen this happen once in a while with a bad power adapter that under/overpowers the router. Is the power light on? Is it flashing?]]> http://www.dslreports.com/forum/remark,22732116 Sun, 19 Jul 2009 05:43:35 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22728319 turbo : I did turn provisionning off.

The device is not locked. I just can't access it anymore. I can't ping it.]]> http://www.dslreports.com/forum/remark,22728319 Sat, 18 Jul 2009 08:38:29 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22723116 mazilo :
said by turbo See Profile :

This week, I got another of those unit for 10$, I've unlocked it, upgraded it to 3.1.17. This morning I wake up and I find the same problem again.
Once unlocked, you will need to turn off Provision feature so that it will not contact to Vonage to get relocked.]]> http://www.dslreports.com/forum/remark,22723116 Fri, 17 Jul 2009 11:01:09 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22722483 turbo : I am also having the same problem as Ferndock2 (posted on 2009-03-16).

Last summer (2008) I got a rtp300 that a co-worker gave to me. I unlocked it and upgraded the firmware. After about 2 hours, I could not access it anymore. I restarted it, and could only access it for about 10seconds. I had to rapidly try to login, then had the time to browse to one other page, and then I could not even ping the device anymore. Then, ou of frustration, after 2weeks, I stopped playing with it.

This week, I got another of those unit for 10$, I've unlocked it, upgraded it to 3.1.17. This morning I wake up and I find the same problem again.

Anyone have any idea?]]> http://www.dslreports.com/forum/remark,22722483 Fri, 17 Jul 2009 09:09:16 EDT Re: Can I use WRTP54G with Lingo's service? http://www.dslreports.com/forum/remark,22714450 mazilo :
said by TEXAS :

Can I use this with Lingo's VOIP Service?
Does Lingo support BYOD?]]> http://www.dslreports.com/forum/remark,22714450 Wed, 15 Jul 2009 19:48:56 EDT Re: Can I use WRTP54G with Lingo's service? http://www.dslreports.com/forum/remark,22714232 anon : Hello Everyone,

I have an unlocked WRTP54G Linksys. Can I use this with Lingo's VOIP Service?]]> http://www.dslreports.com/forum/remark,22714232 Wed, 15 Jul 2009 19:13:05 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22702498 slamdeal : i've followed the exact steps several times for my wrpt54g , and the i dont see any output text at any time while pinging.

what am i doing wrong?

i also have an rtp300, and that one worked but i want to use my wrpt54g for the wireless

DISREGARD!!! I GOT IT TO WORK!!! WOOO

THANKS GUISE]]> http://www.dslreports.com/forum/remark,22702498 Mon, 13 Jul 2009 20:07:41 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22649150 anon : Yeah, I'm also having an issue editing with HEX editor, not sure how to find the correct key to edit. If someone has an edited version of the firmware for the RTP300 send it to me at dzukowsk@gmail.com]]> http://www.dslreports.com/forum/remark,22649150 Fri, 03 Jul 2009 11:03:21 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22648396 anon : I also have the same problem I downloaded the firmware and then I get "upgrade not allow for this login type" which I ignored but I got a ed light on my router, then I go back with the next step on pinging the command but nothing happens, cyt doesn't work yet, please help I have to of those route with 5.01.04 firmware]]> http://www.dslreports.com/forum/remark,22648396 Fri, 03 Jul 2009 03:00:38 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22647660 anon : I'm having a problem, I cannot get the rtp300 to revert backwards bfrom the 5.01.04 firmware, I get to step 4 but the router refuses to downgrade, any suggestions?]]> http://www.dslreports.com/forum/remark,22647660 Thu, 02 Jul 2009 22:23:44 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22601709 toro :
said by axishift See Profile :

I
After the successful unlocking.. I tried to enter again
»192.168.15.1/update.html

And tried the Admin/Admin or admin/admin or Admin/User

It simply won't let me login again? Got that from cyt. Any ideas?
After unlocking, the user for the firmware update page is Admin and the password is blank
And I looked on the linksys site, I thought there was a 5.x firmware and only found 3.x, am I missing something?
The 1.x and 5.x firmwares are Vonage specific. The 3.x is the -NA specific with setup screens like other Sipura/Linksys adapters.]]> http://www.dslreports.com/forum/remark,22601709 Wed, 24 Jun 2009 09:09:24 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22588441 axishift : I have successfully unlocked my WRTP54G ex-Vonage router.
The instructions was very easy, Page1.

Although, I have a couple of questions I did not found.

After the successful unlocking.. I tried to enter again
»192.168.15.1/update.html

And tried the Admin/Admin or admin/admin or Admin/User

It simply won't let me login again? Got that from cyt. Any ideas?

And I looked on the linksys site, I thought there was a 5.x firmware and only found 3.x, am I missing something?]]> http://www.dslreports.com/forum/remark,22588441 Sun, 21 Jun 2009 20:22:47 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22545338 anon : successfully unlocked rtp300-vd. however I would update to the guide to show that the computer must be getting 192.168.15.100 from the ata and that ip showing in tftp32 especially in the second part with the rf file. I orginally had .101 from the ata (no other device connected, it just wanted to start with that even with numbering starting at .100) wf worked on that with the 101 substituted appropriately but somewhere in the rf it tells the ata to look at 100 regardless.
It eventually took the bin which had to be downloaded by cmd prompt rather than windows link and renamed.
I used a hex editor from cnet downloads hex workshop v6 which was fairly simple. entered the line address in a search box at the top which took me right to the spot to edit values which show in red after editing.
Cyt sets Admin/Admin but after loading new na firmware login goes back to admin/admin
thanks for the help]]> http://www.dslreports.com/forum/remark,22545338 Sat, 13 Jun 2009 11:35:52 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22536894 N9MD :
said by fastone :

My MagicJack hack...

Do you know if Magicjack folks change ProxyUserPassword often? I think highly unlikely but thought I would ask.
Er-r-r-r-r! This post most likely belongs in the MagicJack subforum, not here. Anyhow, did you glance at the recent MJ subforum "titles"? Your plight is already under discussion in this thread.

»Defcon 1?: Massive ATA failure]]> http://www.dslreports.com/forum/remark,22536894 Thu, 11 Jun 2009 20:08:50 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22535994 anon : My MagicJack hack with RTP300 hack was working flawlessly for about a month. Now for some reason in Line 1 of Voice it says "Registration State: Failed".

I have rebooted all my networking devices one at a time.

Do you know if Magicjack folks change ProxyUserPassword often? I think highly unlikely but thought I would ask.

Any other ideas? I am going nuts trying all sorts ...

Thank you kindly!]]> http://www.dslreports.com/forum/remark,22535994 Thu, 11 Jun 2009 17:23:44 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22491973 JohnnyPhilko : I would like to get a working img/bin/firmware for the RTP]]> http://www.dslreports.com/forum/remark,22491973 Wed, 03 Jun 2009 19:53:26 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22469133 bigbiz : That would be really appreciated. But it sure sounds like a great deal of work.
I checked out »oldwiki.openwrt.org/OpenWrtDocs(···oot.html

However, I am not sure, being away from this tech stuff for too many years, that I would be able to compile the bootloader.

From a guided solution, at »www.routertech.org/
it the WRTP54G is not listed, so I doubt I would be able do the job.

Thanks, but if it is too much trouble, I should really learn to how to do these things when I get myself(electronic equipment) in such a mess!]]> http://www.dslreports.com/forum/remark,22469133 Sat, 30 May 2009 14:18:42 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22468997 GrauerFuchs : Keep in mind there's a big difference between bootloader and firmware image. The bootloader is what makes loading the firmware possible. Most people will be looking to modify and replace their firmware image. The bootloader, once in place, is modified only to permanently change hard-coded values, and even then, very rarely.

Since you've burned the bootloader, you'll need to replace both bootloader and firmware image code in your machine. The bootloader code is licensed by TI, so you won't find a binary of that uploaded here, either. You might want to begin searching for 'pspboot', which is the name of this machine's bootloader code. I could likely prepare one for you, but it would be subject to extreme delays before I could get it to you.]]> http://www.dslreports.com/forum/remark,22468997 Sat, 30 May 2009 13:38:11 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22464779 bigbiz : All I get is a continuous blinking light! This is not the type of behaviour that I was expecting....

After looking more at the Openwrt page, it does not look even if I wanted to, would be able to recompile the bootloader. Apparently incompatible with the mini-pci bus and incomplete.

my command line entry for TJTAG

tjtag -flash:custom /window:b000000 /start:b000000 /length:10000 /fc:85 /bypass

It was rather quick ( just over 10 minutes ) but when reset, the light blinks continuously. I to get it back to communicate with TJTAG, I have to short pins on the NVRAM. Otherwise it seems like it is totally toast! I tried with address 90000000 like i saw via a hex editor in the bin file, but JTAG just hangs at that address.

Does anyone have a bootloader dump or image?

Thanks]]> http://www.dslreports.com/forum/remark,22464779 Fri, 29 May 2009 14:50:07 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22464168 bigbiz : Thanks for the link to OpenWRT site. I had come across it, but was looking for a highschool like chemistry class instructions.

I will continue trying with TJTAG and the firmwares that I came across. I only found one bootloader 3.1.22 ETSI, and will load it in and see what happens.]]> http://www.dslreports.com/forum/remark,22464168 Fri, 29 May 2009 13:21:58 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22458487 anon : I can confirm that the RTP300 3.1.24 firmware can be modded in exactly the same way that the original poster modded 3.1.17

"Use a hex editor and change offset 0x17 from 4D to 4C and offset 0x3B0004 from 85 DA 20 BB to 3B A5 4D DA"

Also... after an upgrade to the modded 3.1.24, the "Admin" password (for firmware upgrades) is simply blank

Thanks a bunch to the writer if this post... I'm shocked it worked... was fully prepared to brick mine.

Now onto connecting mine to my Cisco UCM7 system - only using mine as a simple ATA in this case]]> http://www.dslreports.com/forum/remark,22458487 Thu, 28 May 2009 14:08:38 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22456473 GrauerFuchs : One of the best resources for addressing would have to be the OpenWRT site for the WRTP54G.
»oldwiki.openwrt.org/OpenWrtDocs(···ardware)
They have all the addresses listed on where to place the bootloader, environment, and firmware images.

I always used the custom addressing to ensure things were set properly. The WRTP54G is a very different machine than the WRT54G. I have also never used the Skynet output, so I'm afraid I can't advise you there. One thing to consider when using a mass-produced code image is that it may change your MAC addresses. Those are coded into the bootloader segment.

Yes, the firmware now loaded on my WRTP54G is the one from the Linksys site. To load this unmodified firmware, the bootloader code must be altered to remove the hard-coded information specific to the provider. It must also have the NA counterparts to this information put into place. Specifically, the product code must be changed at a minimum, and the default password set to something sane.]]> http://www.dslreports.com/forum/remark,22456473 Thu, 28 May 2009 07:27:19 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22452544 bigbiz : What would the best option for a completely dead WRTP54g v1.1 Spansion

1) I have tried TJTAG with a cfe.bin generated from Skynet. Do I need to specify the addresses (00000x0) on the chip ?

2) A whole flash of a firmware was not successful. It could also be the same firmware location problem.

3) Can a firmware dump from another unit solve the problem?

GrauerFuchs, did you use a firmware from the Linksys site?

Thanks again]]> http://www.dslreports.com/forum/remark,22452544 Wed, 27 May 2009 14:53:22 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22450418 GrauerFuchs : It does indeed work. I've used TJTAG to permanently unlock a WRTP54G so it will accept unmodified NA firmwares and have no chance of being re-locked. Having used both softwares, I found that the TJTAG program was a little more capable, flexible, and faster.]]> http://www.dslreports.com/forum/remark,22450418 Wed, 27 May 2009 08:32:02 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22448769 mazilo :
said by bigbiz See Profile :

Do you konw if TJTAG or WTR54G is configured for the correct addresses for a cfe or wholeflash upload?
IIRC, I once used the WTR54G program to interface my WRTP54G (Vonage locked) to my computer using an un-buffered JTAG cable.]]> http://www.dslreports.com/forum/remark,22448769 Tue, 26 May 2009 21:23:05 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22448375 bigbiz : I have also tried 192.168.15.1 - nothing

The lights go solid, then off.

Is a bootloader from Skynet package suitable, or will i need to upload a cfe.bin dump from another system?

Do you konw if TJTAG or WTR54G is configured for the correct addresses for a cfe or wholeflash upload? I see the option custom flash, with a length, window and start, but do not know how to use it.

Thanks]]> http://www.dslreports.com/forum/remark,22448375 Tue, 26 May 2009 19:54:19 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22448273 mazilo :
said by bigbiz See Profile :

... ping 192.168.1.1 does nothing.
IIRC, the default IP Address of a WRTP54G on its LAN port is 192.168.15.1.]]> http://www.dslreports.com/forum/remark,22448273 Tue, 26 May 2009 19:32:52 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22447077 bigbiz : I have a wrtp54g v1.1

A number of months ago i failed flashing using CYT and it has been dead since.

Getting the tools I needed, I have tried using the JTAG cable, and am able to communicate with the Spansion chip on the board and successfully flash cfe.bin but to no avail. ping 192.168.1.1 does nothing.

I am using TJTAG and the Bootloader creator from Skynet so that I can enter my MAC address.

As it sounds insensible to try to upload a whole flash file via the JTAG before even getting the bootloader to work, I would like to know if anyone has succeeded with a completely dead WRTP54g to breath it back to life.

Thanks,]]> http://www.dslreports.com/forum/remark,22447077 Tue, 26 May 2009 15:53:43 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22424586 anon : I found a working img/bin/firmware for the RTP300 that was downgraded if anyone wants it, but it is against forum policy to post it (for good reason). This firmware (3.1.24) is for those who do not know how to use hexedit and mod it as Phoenix talks about on page 1.

This is the primary thread for unlocking the Vonage RTP300 with 5.01.04, but one should start on page 6 where you will need to read Linux fanboy's post. Then go to page 1 and start working from there.]]> http://www.dslreports.com/forum/remark,22424586 Thu, 21 May 2009 19:06:55 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22422692 anon : GrauerFuchs

Yes!. Where can we get the modified RTP300 firmware?
Or
Step-by-step on how to edit the bins with hexedit.]]> http://www.dslreports.com/forum/remark,22422692 Thu, 21 May 2009 13:19:39 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22422674 GrauerFuchs : If you have an RTP300, you need the modified RTP300 firmware, not the WRTP54G firmware.]]> http://www.dslreports.com/forum/remark,22422674 Thu, 21 May 2009 13:15:49 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22422660 anon : Phoenix...is there anyway you could post the working firmware for a Vonage rtp300 so we can go to BYOD VOIP providers-for those able to downgrade to 1.00.62?

I have tried some of them now that I have downgraded and at about 12% (at upgrade firmware screen) I keep getting "Invalid Code Pattern"

thanks,
wirelessrrat]]> http://www.dslreports.com/forum/remark,22422660 Thu, 21 May 2009 13:14:07 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22420672 anon : I finally downgraded to 1.00.62 on my old Vonage RTP300-dont ask how I just kept screwing with it-and can login with a second window/tab using "Admin/Admin" (yes big "A" and must already be logged in with "admin/admin" in another window simultaneously). I think this (»/forum/r22207937) is what helped me with the downgrade.

I am now stuck at Step 5-4, where it says: Locate the modified WRTP54G-NA 3.1.17 firmware and initiate the upgrade process. Wait a few minutes and the device will reset itself and take you back to the login page. Username and pass should be admin/admin. Ensure that the firmware is 3.1.17." When I try this the router gets to about 11-12% and stops indicating "Status: invalid code pattern." I have tried replacing the current firmware (1.00.62-modified) with the firmware 3.1.17USmod and the one from Linksys at 3.1.24 and I get the same error. Do these images/bins need edited to work, if so how?

Can anyone help me out? Just my luck now stuck on the last step!! :mad:

Note: If you can get your router to the point I am at (1.00.62) you can manipulate the Voice settings by:
1. Running CYT 3.5.exe and pressing 1 and wait about 1 minute.
2. logging into the router as admin/admin.
3. Copy paste "192.168.15.1/Voice_adminPage.html" into another tab/window where you login with "Admin/Admin"]]> http://www.dslreports.com/forum/remark,22420672 Thu, 21 May 2009 01:03:45 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22419570 anon : I think I used the right firmware. I did download the alternative firmware for the RTP300- not sure how to mod the firmware.

One thing that keeps coming up is it is an .img and I have to rename it ....bin so the router will take it. The router does nothing.

I will start over and see if I can follow the tutorial again. The only error I can think I made would be failing to mod the firmware as needed. I would be grateful if someone could write up a "dummies" guide to editing the original firmware.]]> http://www.dslreports.com/forum/remark,22419570 Wed, 20 May 2009 20:53:56 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22376972 Phoenix2088 : Did you use the appropriate firmware for the RTP300 and mod it?]]> http://www.dslreports.com/forum/remark,22376972 Tue, 12 May 2009 12:19:04 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22367784 anon : I am trying the RTP300 with 5.01.04. I went through the tutorial and replaced the 1.0062 from a later post. Tftp32 showed a transfer bar that took about 5 seconds to complete. I waited about 10 minutes and the router acted as if nothing ever happened.

What am I missing?]]> http://www.dslreports.com/forum/remark,22367784 Sun, 10 May 2009 15:52:34 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22306090 axishift : Hi, I am just curious if the first page can still unlock a Vonage WRTP54G with 5.01.04 firmware?

I am about to cancel my vonage anytime and would like to unlock it also.]]> http://www.dslreports.com/forum/remark,22306090 Tue, 28 Apr 2009 04:02:25 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22278347 nchetoora : Hey i was hoping you or anyone could help me with unlocking the RTP300, I've gotten pretty far with all the setting up, but the part i can't seem to get pass is downgrading the firmware. i am not sure if i am not renaming the firmware properly. i actually rename it using dos and i am using windows vista x64 ultimate. i also tried it with xp. i turned off my firewall and anti-virus software. i was able to ping the device and get the unlock console message. but the other set of pings don't seems to do anything. i can't see the transfer in TFTP32. any help will be good. if someone can tell me or give me some help on the renaming of the firmware to von10062.bin that will be good. any help will be appreciated.

thanks
Nick]]> http://www.dslreports.com/forum/remark,22278347 Wed, 22 Apr 2009 11:40:05 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22265389 teran54 :
said by toro See Profile :

Admin / no password
Thanks toro.]]> http://www.dslreports.com/forum/remark,22265389 Mon, 20 Apr 2009 10:23:38 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22265025 toro :
so I have no need for vonage, but have this un-useable router - and would just like to use it for my home network without voip functions.
Yes, you can use it as a basic wireless router and ignore the VoIP part.]]> http://www.dslreports.com/forum/remark,22265025 Mon, 20 Apr 2009 08:55:41 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22265021 toro : Admin / no password]]> http://www.dslreports.com/forum/remark,22265021 Mon, 20 Apr 2009 08:54:20 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22253187 teran54 : Thank you Phoenix2088 for the tutorial, everything went smoothly. Now I would like to upgrade the firmware, but I don't know the username/password to enter. I have tried every type of combo to no avail. Any suggestions?
Thanks]]> http://www.dslreports.com/forum/remark,22253187 Fri, 17 Apr 2009 13:27:50 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22252431 anon : Hi
Just wondering if this will help me just use the router without voip. I don't have vonage, don't want it. But I got this router from them when I tried their service, which was terrible.
I can't sell the router - I actually did sell it, but the guy I sold it to was not allowed to use it for vonage and they would not transfer it to him. So I had to take it back.

so I have no need for vonage, but have this un-useable router - and would just like to use it for my home network without voip functions.]]> http://www.dslreports.com/forum/remark,22252431 Fri, 17 Apr 2009 11:34:41 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22207937 anon : Hi,

This is great thread! I just unlocked my RTP300 that I bought for $5 on a garage sale. Along the way I found much much simpler way to do it. Here it goes:

1. First of all you need to be able to login as "admin". If you cannot do that then reset the router by pushing reset button for 10-15 seconds and after it reboots you should be able to use default username/password "admin/admin".


2. Download CYT unlocker
»/r0/download/1···in32.zip


3. Save The following code into a file rpt300_unlock.txt. Remove any code and comment lines that you don't need. If you are using Windows then add a space to the end of each line. DOS style line endings do weird things.

You can download 1.00.62 firmware directly from the Vonage servers or use local tftp server.

Bare minimum version of the script looks like this:


4. Login into the router GUI as "admin/admin" at »192.168.15.1/ (if you are using local tftp server you restart it now).


5. Go directly to this page: »192.168.15.1/cgi-bin/firmwarecfg
Browse to rpt300_unlock.txt and click "Update Gateway" ignore any errors.


6. Now go to back to the main menu, Administration tab, Diagnostics, and popup Ping tool. Run this command: "0.0.0.0 &&sh /var/tmp/config.bin"


This must be a little secret of one of the system developers - this command is exactly the length of the input field - no need for web developers plugin. :)


7. When router reboots disconnect it from the internet and run CYT as described elsewhere in this thread.


If everything works then after one more reboot you could first login as "admin/admin" at »192.168.15.1/ and then as "Admin/Admin" at »192.168.15.1/update.html and »192.168.15.1/Voice_adminPage.html pages. If you hooked up serial console cable to the RTP300 motherboard "Admin/Admin" will work at the linux login prompt as well. If you still having problemsrepeat steps 5 through 7 exactly as been written. Built-in busybox is quirky and one space character could make a difference.


It is also worth to mention here that on some of the LinkSys routers after you reset it and login as "admin/admin" first on the main page then subsequent combination of Username "user" and Password "d6nw5vlx2pc7st9m" or "AB2ChJScbtR5I" could let you to the /update.html page.


Enjoy!]]> http://www.dslreports.com/forum/remark,22207937 Thu, 09 Apr 2009 09:06:47 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22186272 Velund :
said by ferndock2 See Profile :

I was able to establish a stable connection to the RTP300 LAN port but it required that I have a second computer connected to another of the unit's LAN ports and a fan blowing air into the bottom of the unit. Yes, I'd say the unit is having hardware problems.
Recently got similar unit (from eBay). Turned out to be broken soldering joint below TI BGA chip. If you don't have professional BGA rework equipment handy, I would recommend to ask someone equipped to reflow whole board. It may be more expensive than another used RTP300 of course.]]> http://www.dslreports.com/forum/remark,22186272 Sun, 05 Apr 2009 08:17:45 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22126212 usbjtag : Use JTAG will completely make the NA version. Empty the keys. Load the 3.1.24 (RTP300) and 3.1.27 (WRTP54G).]]> http://www.dslreports.com/forum/remark,22126212 Wed, 25 Mar 2009 12:31:06 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22085377 ferndock2 : The RTP300 has firmware rev 5.01.04. I'll try Mazilo's suggestion as soon as I can clear some time (I've already spent the better part of two days on this beast).]]> http://www.dslreports.com/forum/remark,22085377 Tue, 17 Mar 2009 19:39:20 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22079374 mazilo :
said by ferndock2 See Profile :

I tried the CYT Unlocker versions 3.9 and 4.6.
If your device runs on a firmware v5.x.x, then CYT_Unlocker isn't going to work. You may have to resort to the NAizer for CYT by DogFace05.

If you can downgrade its firmware, perhaps CYT_Unlocker will do the trick.
--
Mazilo always prays for FREEBIES!
US Phone: +1-678-601-0907
UK Phone: +44-703-194-2574
]]> http://www.dslreports.com/forum/remark,22079374 Mon, 16 Mar 2009 20:16:51 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22079155 ferndock2 : I was able to establish a stable connection to the RTP300 LAN port but it required that I have a second computer connected to another of the unit's LAN ports and a fan blowing air into the bottom of the unit. Yes, I'd say the unit is having hardware problems. Once I established the stable connection I was able to login with admin/admin and manipulate any parameters that were allowed. Tried to login with user/tivonpw but that didn't work. Then I tried the CYT Unlocker versions 3.9 and 4.6. Let each of them run multiple times for up to 5 minutes but nothing happened. Recommendations?]]> http://www.dslreports.com/forum/remark,22079155 Mon, 16 Mar 2009 19:33:49 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22078042 ferndock2 : I don't have another RTP300. I do have another 12V 1.5A power supply which I connected. No difference in the RTP300's operation.]]> http://www.dslreports.com/forum/remark,22078042 Mon, 16 Mar 2009 15:58:56 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22077993 mazilo :
said by ferndock2 See Profile :

Unfortunately, the intermittent connectivity I get from the LAN ports is so short that have no time to try anything else.
Do you have another unit of this device that is currently working? If so, try to swap their AC/DC adapter and see if this problem will get resolved.]]> http://www.dslreports.com/forum/remark,22077993 Mon, 16 Mar 2009 15:47:53 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22077886 ferndock2 : Unfortunately, the intermittent connectivity I get from the LAN ports is so short that have no time to try anything else. I might get a connection for 2 seconds, then it goes away, and it might or might not reconnect. Sometimes it's enough time to type in admin/admin which takes me to the page 192.168.15.1/cgi-dir/webcm where IE7 says it cannot display that page.]]> http://www.dslreports.com/forum/remark,22077886 Mon, 16 Mar 2009 15:31:55 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22077846 mazilo :
said by ferndock2 See Profile :

As I said in a later post, I was able to get very brief periods of connectivity from the LAN ports that would show me the Linksys login page via 192.168.15.1.
If you have the WAN port connected, what will happen if you disconnect the WAN port while you are able to get the LAN connection from your computer? Will the router still stable?
--
Mazilo always prays for FREEBIES!
US Phone: +1-678-601-0907
UK Phone: +44-703-194-2574
]]> http://www.dslreports.com/forum/remark,22077846 Mon, 16 Mar 2009 15:25:12 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22077750 ferndock2 : I have tried with the WAN both connected and disconnected. As I said in a later post, I was able to get very brief periods of connectivity from the LAN ports that would show me the Linksys login page via 192.168.15.1. All of those happened when the WAN was connected but never when it was disconnected.]]> http://www.dslreports.com/forum/remark,22077750 Mon, 16 Mar 2009 15:06:31 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22077585 mazilo :
said by ferndock2 See Profile :

I did as Toro suggested with negative result. I also gave it 30-second and 1-minute pushes on the reset button. Only one time did this yield a connection that allowed me to reach 192.168.15.1. On that connection I saw the Linksys login page and typed admin/admin. At that point IE7 popped its "remember this password" and by the time I got rid of that IE7 locked up forcing me to restart it. Since, then, no connections. Otherwise, this unit won't give a steady connection indicator light on any of the LAN (Ethernet, yellow) ports. The light will only flash occasionally on the port to which a cable is attached to other equipment. Can't ping the unit. Other suggestions?
When you did this process, did you have the WAN port connected to the Internet? If so, try to re-do this process without Internet connection.
--
Mazilo always prays for FREEBIES!
US Phone: +1-678-601-0907
UK Phone: +44-703-194-2574
]]> http://www.dslreports.com/forum/remark,22077585 Mon, 16 Mar 2009 14:42:51 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22077323 ferndock2 : Mazilo, I can't use CYT because I can't establish a connection to the RTP300 through its LAN (Ethernet, yellow) ports. Those ports give highly intermittent, very short-term connections. The only data port on the unit that seems to work correctly is the WAN (Ethernet, blue) connection. Either I coax the LAN ports into working or find a way to log into the WAN port to program it.]]> http://www.dslreports.com/forum/remark,22077323 Mon, 16 Mar 2009 13:57:11 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22077259 mazilo :
said by ferndock2 See Profile :

Toro, thanks for your input. Anybody else have suggestions?
Perhaps, you should consider waiting for this NAizer for CYT utility.]]> http://www.dslreports.com/forum/remark,22077259 Mon, 16 Mar 2009 13:45:26 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22077155 ferndock2 : Toro, thanks for your input. Anybody else have suggestions?]]> http://www.dslreports.com/forum/remark,22077155 Mon, 16 Mar 2009 13:26:21 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22077124 toro : I've been dealing with dozens of these routers before but I've seen only one with that issue. In that case it was a WRTP54G where the LAN ports were shot but the VoIP and wireless are working fine.
Unfortunately it's a hardware issue and I have no idea how to fix it.]]> http://www.dslreports.com/forum/remark,22077124 Mon, 16 Mar 2009 13:18:00 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22077097 ferndock2 : Power light is on steadily. The only times it flashes are when I power down/up or hit reset. After a power up and with the WAN (Internet) port attached to my router, the RTP300's LAN port will turn on and off at a slow rate that infrequently allows me to display the Linksys login screen. I found that by using Admin/Admin to login it says I'm not allowed at that level. Using admin/admin or user/user have not been successful because the LAN port connection doesn't stay up long enough to see a next screen. The LAN port rarely shows a connection greater than 2 seconds. How can I get this unit to give me a steady LAN connection?]]> http://www.dslreports.com/forum/remark,22077097 Mon, 16 Mar 2009 13:13:16 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22076605 toro : Does the power light flash for several seconds every once in a while ? If it does, you may be dealing with a defective unit (see »Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04)]]> http://www.dslreports.com/forum/remark,22076605 Mon, 16 Mar 2009 11:55:24 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22076341 ferndock2 : I did as Toro suggested with negative result. I also gave it 30-second and 1-minute pushes on the reset button. Only one time did this yield a connection that allowed me to reach 192.168.15.1. On that connection I saw the Linksys login page and typed admin/admin. At that point IE7 popped its "remember this password" and by the time I got rid of that IE7 locked up forcing me to restart it. Since, then, no connections. Otherwise, this unit won't give a steady connection indicator light on any of the LAN (Ethernet, yellow) ports. The light will only flash occasionally on the port to which a cable is attached to other equipment. Can't ping the unit. Other suggestions? ]]> http://www.dslreports.com/forum/remark,22076341 Mon, 16 Mar 2009 11:05:21 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22076044 toro :
said by ferndock2 See Profile :

Everything I've read says I should be able to connect to it at 192.168.15.1 but that doesn't work.
Power on the router and let it run for 2-3 minutes, then push and hold the reset button for at least 8 seconds (until the lights start flashing). After that, your router should be reset to the factory settings and should have the IP 192.168.15.1 on the LAN ports (unless it's defective).]]> http://www.dslreports.com/forum/remark,22076044 Mon, 16 Mar 2009 10:09:17 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22073633 ferndock2 : I have an RTP300 that was given to me by someone who stopped using Vonage. Everything I've read says I should be able to connect to it at 192.168.15.1 but that doesn't work. The only connection I've been able to make is with a reversal cable directly from my PC to the RTP300 Internet port. It is then that I learn that the RTP300 says its address is 169.254.226.127. When I connect to that address I get a login window but cannot get in by using admin/admin or Admin/Admin or user/user. Instead I get a screen telling me my login doesn't allow me access. Pushing the Reset button, powering off/on, and the combination of the two do nothing. I can't run CYT because it only works with addresses in the 192.168 range. So, how can I talk to this unit and make it take new information?]]> http://www.dslreports.com/forum/remark,22073633 Sun, 15 Mar 2009 19:19:27 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22038726 mazilo :
said by toro See Profile :

Have you looked at this »[Equipment] WRTP54G-ST
Outch ..., I completely forgot about that thread. Many thanks and I appreciated that.]]> http://www.dslreports.com/forum/remark,22038726 Mon, 09 Mar 2009 09:03:46 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22038697 toro : Have you looked at this »[Equipment] WRTP54G-ST]]> http://www.dslreports.com/forum/remark,22038697 Mon, 09 Mar 2009 08:50:29 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22030699 mazilo :
said by TM :

I want try to unlock, the problem is that if it doesn't work? what should i do? Cause i'm not in USA now, i'm in other country and here this product costs about $100,00...
No one here seems to have a WRTP54G-ST, except you. That said, it will take sometimes before you will be able to find someone with a WRTP54G-ST to attempt such an unlocking. AFAIC, $100 is pretty steep. So, when in doubt, I certainly would recommend that you ought to return this product and get your money back to buy a WRTP54G-NA (non-customized).
--
Mazilo always prays for FREEBIES!
US Phone: +1-678-601-0907
UK Phone: +44-703-194-2574
]]> http://www.dslreports.com/forum/remark,22030699 Sat, 07 Mar 2009 11:28:59 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22030543 anon : My doubt is, this tutorial is for every wrtp54g or not? cause the model of mine is wrtp54g v2 and in the configuration menu its say wrtp54g-st.

I want try to unlock, the problem is that if it doesn't work? what should i do? Cause i'm not in USA now, i'm in other country and here this product costs about $100,00...

So i don't wanna loose money.

Anyway, if no one know a solution, i will try it, cause i already have an wireless router, and if the voip doesn't work, this product has no utility for me... :(

tks for the help.]]> http://www.dslreports.com/forum/remark,22030543 Sat, 07 Mar 2009 10:53:15 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22030164 mazilo :
said by TM :

Hey guys. Pls, i broght one WRTP54G ver.2 in USA. And the voice menu is blocked. Can i use this tutorial to unlock the ver.2 or it just works on 1.
Why not give it a try and let us know the outcome?]]> http://www.dslreports.com/forum/remark,22030164 Sat, 07 Mar 2009 08:50:51 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22029333 anon : Hey guys. Pls, i broght one WRTP54G ver.2 in USA. And the voice menu is blocked. Can i use this tutorial to unlock the ver.2 or it just works on 1.

Tks for the help.]]> http://www.dslreports.com/forum/remark,22029333 Fri, 06 Mar 2009 23:55:02 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,22023508 tohchi : Thank you so much!!
Just bought this WRTP54G today from circuit city at $12!!

After 4 hours searching for info on internet included with Phoenix2088 instruction, I finally have it done!

I was first reluctant to hook the internet cable to have the firmware upgrade to 5.01.04. After several attempts, I just gave up and found out that 5.01.04 is much easier!!!]]> http://www.dslreports.com/forum/remark,22023508 Fri, 06 Mar 2009 00:07:36 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21912871 toro : I have no idea. If I knew I would have fixed mine :(
I don't think another firmware would be of any help.]]> http://www.dslreports.com/forum/remark,21912871 Fri, 13 Feb 2009 17:20:36 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21911969 rmshakil : ok I did try a 2 ampare adapter and found the samw trouble and than I removed Q5 and now it is getting on. Here my question is is there any way to trace the fault or repair the VOIP section?? Can I try upgrading the firmware and see how it behave or this mean the VOIP is dead? ]]> http://www.dslreports.com/forum/remark,21911969 Fri, 13 Feb 2009 14:54:40 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21906950 toro : From my experience (I've seen at leat 3-4 doing the same), that router not bricked. The firmware loads properly if the wireless light goes on.
The voice part however may have gone bad. It may work with a better power adapter (a switched power adapter with regulated voltage).
If another power adapter doesn't work, you can desolder the part labeled Q5 (the voltage regulator for the Legerity chip - see the picture) and it should become stable but will work only as a wireless router (kind of an "unorthodox" solution, but I applied it successfully to 3 or 4 routers so far)
]]> http://www.dslreports.com/forum/remark,21906950 Thu, 12 Feb 2009 16:39:57 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21906878 rmshakil : Power light start flashing after powering the device and than wirless light comes on(both light get steady)and after 6 seconds or so all the light lights up and restart from power light again. This keep going on and on. I tried to press the reset button more than minute cycle the power with keep the button pressed, left is with internet and also tried connecting PC with it no luck, keep cycling. Hope this will help to understand the problem thanks ]]> http://www.dslreports.com/forum/remark,21906878 Thu, 12 Feb 2009 16:26:14 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21897163 toro :
I couldn't find "How to debrick a WRTP54G"
You may want to describe exactly the symptoms.
Do you have a serial console to see if at least the boot loaded starts ? Does the power light blink when you power it on ?]]> http://www.dslreports.com/forum/remark,21897163 Tue, 10 Feb 2009 21:28:04 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21895959 rmshakil : I am reading these threads and seems some of you are real pro in this field. But I couldn't find "How to debrick a WRTP54G" I got some info from open wrtp but don't see the complete procedure. I have made my own unbuffered cable and looking for rest of the information to fix the boot section I would really appreciat if someone guide me through and help me out of it. I don't have any software, utility or boot sector image?? thanks]]> http://www.dslreports.com/forum/remark,21895959 Tue, 10 Feb 2009 18:15:51 EDT Re: Man I was all excited when I saw this post http://www.dslreports.com/forum/remark,21879455 DogFace05 : It sounds like you have your computer's firewall enabled and blocking your RTP300's attempt to contact CYT's "Simple xml server." You need to disable any such firewall.]]> http://www.dslreports.com/forum/remark,21879455 Sat, 07 Feb 2009 14:50:57 EDT Re: Man I was all excited when I saw this post http://www.dslreports.com/forum/remark,21877631 chickenrob : Yes I have searched through many many forums and read all of this thread. could there be some networking issue? The cyt program seems to be able to tell that I have a rtp300 attached. ]]> http://www.dslreports.com/forum/remark,21877631 Sat, 07 Feb 2009 01:47:14 EDT Re: Man I was all excited when I saw this post http://www.dslreports.com/forum/remark,21869818 mazilo :
said by chickenrob See Profile :

Anyone have any ideas about this?
CYT_unlocker has its weak points, too. You probably need to go back reading all posts on this thread or search through this forum.]]> http://www.dslreports.com/forum/remark,21869818 Thu, 05 Feb 2009 19:21:34 EDT Man I was all excited when I saw this post http://www.dslreports.com/forum/remark,21868347 chickenrob : unfortunately it does not work for me! I went through the instructions twice on my rtp300. I have verified I am running the 1.00.62 firmware. Everything up to that point went fine but I am unable to unlock using cyt. It never gets past "Simple xml server is waiting for your device" screen In the left lower corner it says xml server started. In the right corner it says Your device is rtp300. Anyone have any ideas about this? ]]> http://www.dslreports.com/forum/remark,21868347 Thu, 05 Feb 2009 15:33:55 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21819629 toro : Use the same browser window. Login first as admin/admin then enter /Update.html (if that doesn't work try /Update.htm) and when prompted to login again use Admin/Admin]]> http://www.dslreports.com/forum/remark,21819629 Wed, 28 Jan 2009 08:52:50 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21815966 anon : when trying to login to the update.html I get a 404 error

404 Not Found
The requested URL '//Update.html' was not found on this server.]]> http://www.dslreports.com/forum/remark,21815966 Tue, 27 Jan 2009 16:05:39 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21815852 anon : Yes...I believe so!

I have one page open before running tftpd and then once if configures, I open another page and try to login with Admin and user

It will not work..however, I can turn right around and login with admin/admin only...much like NOTHING has changed.

That is why I think I must be overlooking something]]> http://www.dslreports.com/forum/remark,21815852 Tue, 27 Jan 2009 15:46:59 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21815796 toro : You must first login to the router's web interface as admin/admin and then try to access the /Update.html which will prompt you to login again (at this point login as Admin/Admin).
Is that what you are doing ?]]> http://www.dslreports.com/forum/remark,21815796 Tue, 27 Jan 2009 15:38:16 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21815723 anon : Yes...I meant CYT..not tftpd.

I started at step 5 at first and had no luck...then I went through all the steps to see if that helped...it has not as of yet.

Again, seems and states it provisioned correctly but, I cannot login with any passwords except admin, admin and then of course it is still showing the default linksys page with same firmware]]> http://www.dslreports.com/forum/remark,21815723 Tue, 27 Jan 2009 15:24:17 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21815602 Phoenix2088 : Are you using CYT at this step?]]> http://www.dslreports.com/forum/remark,21815602 Tue, 27 Jan 2009 15:05:44 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21815502 anon : Just found this thread today and I have been trying for the better part of several hours to unlock my wrtp54g.

However, I seem to be overlooking something.

My router has the 1.00.62 firmware so, I started at step 5

I can run tftpd32 and it SEEMS to finish the provisioning.

It is when I use another tab to login, it gives me the following message

Error: User not allowed to login this user level.

I can log back into the router using the default passwords but, I cannot get into the voice tab so I may upgrade the firmware.

I am sure I am missing something but, cant figure out what it is.

Could I buy a clue?!! : )]]> http://www.dslreports.com/forum/remark,21815502 Tue, 27 Jan 2009 14:52:37 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21815048 toro : Yeah, I've been using JTAG for months with the VT2x42 devices. I just don't see what would be the use to read/write information from/to the mtd5 partition (the primary xml config) or why would someone bother about the checksum.
Once unlocked, these units can be provisioned easily through HTTP ot TFTP, which is what people on this forum have been doing for years.]]> http://www.dslreports.com/forum/remark,21815048 Tue, 27 Jan 2009 13:37:43 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21815006 mazilo :
said by toro See Profile :

Could you please explain a little further how are you trying to accomplish the unlock based on data stored in /dev/mtd5 ?
This post will probably answer to your question.]]> http://www.dslreports.com/forum/remark,21815006 Tue, 27 Jan 2009 13:32:19 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21813315 toro : Could you please explain a little further how are you trying to accomplish the unlock based on data stored in /dev/mtd5 ?
And how would you be able to upload data in the mtd5 partition if the router is still locked ?]]> http://www.dslreports.com/forum/remark,21813315 Tue, 27 Jan 2009 08:32:28 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21802526 usbjtag : Hi, I am able to unlock the RTP devices. I am now interested in the configuration in md5. It started with LMMC and we can unzip it with zlib. I just cannot find how to get the CRC checksum. If we can generate this checksum we should be able to generate valid configuration file.
The reason is we should be able to skip the CYT tool for device like VT2442. VT2442 can upload configuration and if we generate legal config then the missing GUI to config the VOIP part will not be big issue any more.
Does anyone know how to generate the checksum of the configuration?]]> http://www.dslreports.com/forum/remark,21802526 Sun, 25 Jan 2009 02:24:28 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21792847 anon : Thank you for the instructions. I have one of these router and was looking to unlock for a long time and did not get much information. This made the unlock a breeze. Thank a lot. ]]> http://www.dslreports.com/forum/remark,21792847 Fri, 23 Jan 2009 09:58:49 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21730059 GrauerFuchs : That is what a standard means, is it not? It's little more than a listed definition intended to ensure devices of different design and manufacture produce a response that will reliably fall within certain parameters. I do not dispute that this standard does not guarantee reliability of signal transmission once it has left the device. My previous statement should have been worded differently. My apologies.
To clarify another point that may have been misinterpreted, the device's output will not differ based on its physical location, but as DogFace05 stated, it does not guarantee the response will be within standards of nations outside the jurisdiction of the ETSI.
The point on legality is well taken. I should have specifically mentioned that it would not guarantee operation within the guidelines of the FCC, and as such, could and likely would be illegal in the USA.]]> http://www.dslreports.com/forum/remark,21730059 Mon, 12 Jan 2009 20:20:25 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21723235 anon : Thanks for the clarification. Where can I get the modified WRTP54G 3.1.27-NA (non-ETSI) firmware? I searched here but can only find the ETSI version. Thanks.]]> http://www.dslreports.com/forum/remark,21723235 Sun, 11 Jan 2009 17:45:07 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21722892 DogFace05 :
said by GrauerFuchs See Profile :

Basically, the ETSI firmware is one that follows the standards they've set to guarantee a reliable and uniform response from the WRTP54G no matter which country it is in and what country's phone devices are connected.
Where did you come up with this idea? it's not at all the case. The ETSI version of the firmware is specifically designed for the purpose of complying with the communications regulations pertinent to the European Union (as defined and set forth by the ETSI), so that the device operates in accordance with their laws and may be legally sold and used within their territory. It has no relevance whatsoever to guaranteing anything with respect to quality of reliability or response in any other country or territory. In fact, improperly operating (and in particular selling) a WIFI device designed according to ETSI standards in the US, can produce interference in a frequency band allocated for other use, and is illegal. That said, if you make sure to operate it within FCC specified limits, you'll be fine. In particular, do not operate it on any of the extra channels beyond those that are available in FCC compliant WIFI equipment.]]> http://www.dslreports.com/forum/remark,21722892 Sun, 11 Jan 2009 16:37:28 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21721307 GrauerFuchs :
said by MrVile :

mazilo, when looking on the Linksys site, the newest firmware they're showing for the WRTP54G-NA is 3.1.24 (I know it needs to be modified first).

If you still recommend 3.1.27, is this a good modified version?:

»[Unlock] WRTP54G Unlocked firmware 3.1.27 ETSI

I saw your comments in that post, that's why I'm asking. What does the ETSI mean/stand for? Thanks.
European Telecommunications Standards Institute
Basically, the ETSI firmware is one that follows the standards they've set to guarantee a reliable and uniform response from the WRTP54G no matter which country it is in and what country's phone devices are connected. There is speculation on whether or not it holds any value over the other standards if used in North America, but no real answers yet.
There's a WRTP54G 5.01.04 firmware on the OpenWRT site:

»wiki.openwrt.org/OpenWrtDocs/Har···/WRTP54G

Are there any reasons not to use this version? Thanks.
The 5.01.04 firmware is a provider locked firmware. It is not an NA firmware.]]> http://www.dslreports.com/forum/remark,21721307 Sun, 11 Jan 2009 11:56:29 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21719332 anon : There's a WRTP54G 5.01.04 firmware on the OpenWRT site:

»wiki.openwrt.org/OpenWrtDocs/Har···/WRTP54G

Are there any reasons not to use this version? Thanks.]]> http://www.dslreports.com/forum/remark,21719332 Sat, 10 Jan 2009 23:21:34 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21719134 anon : mazilo, when looking on the Linksys site, the newest firmware they're showing for the WRTP54G-NA is 3.1.24 (I know it needs to be modified first).

If you still recommend 3.1.27, is this a good modified version?:

»[Unlock] WRTP54G Unlocked firmware 3.1.27 ETSI

I saw your comments in that post, that's why I'm asking. What does the ETSI mean/stand for? Thanks.]]> http://www.dslreports.com/forum/remark,21719134 Sat, 10 Jan 2009 22:52:15 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21714778 mazilo :
said by MrVile :

If so, what is the highest firmware I can safely install?
You are better off to install the newest firmware WRTP54G-NA_3.1.27.]]> http://www.dslreports.com/forum/remark,21714778 Sat, 10 Jan 2009 09:26:27 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21714163 anon : SUCCESS!!! :D

Since I thought I was getting the error because of the letters or special characters in the commands, I started out with 127.0.0.1 and added commands one by one to see when I'd get the error. That's when I figured out that if I typed the whole line instead of pasting it, it worked! I have no idea why the pasting was messing it up because I was pasting from notepad. So, if anyone else has this problem, type the ping commands in manually!

I'm really sorry, this was my own stupid mistake. Thanks to everyone who helped.

One more question, I'm currently unlocked at firmware version 3.1.17, is there any advantage to going to a newer firmware (3.1.24)? If so, what is the highest firmware I can safely install? Thanks again.]]> http://www.dslreports.com/forum/remark,21714163 Sat, 10 Jan 2009 01:43:45 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21713944 anon : Phoenix, I tried your suggestion and unfortunately, it didn't work. I did notice something that got my hopes up for a second, though. When I clicked the Ping button, I'd get the error popup message I was getting before but if I just hit enter, I didn't get the same error. Instead, "Unknown Host" would appear in the large status box below. When I pasted the second line and hit enter, it'd disappear from the ping box and no other messages would appear, same for the last line. I waited but nothing ever showed up in that box. Does this info help any? Thanks.]]> http://www.dslreports.com/forum/remark,21713944 Sat, 10 Jan 2009 00:25:19 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21710765 anon : I see, Thanks for a push in the right direction......I will report back if I have any luck with the RT31P2]]> http://www.dslreports.com/forum/remark,21710765 Fri, 09 Jan 2009 15:16:02 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21709949 anon : Phoenix2088, thanks again for the reply. I'll try your suggestion tonight after I get home from work and report back with the results. I have a feeling the error is caused by the letters or special characters in the commands but we'll see.

Does anyone happen to have the link to the original WRTP54G unlock post by Velund, I can't seem to find it. Maybe he can help shed some light on the problem.

Thanks again.]]> http://www.dslreports.com/forum/remark,21709949 Fri, 09 Jan 2009 13:06:42 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21709789 Phoenix2088 :
said by sean7326 :

Im using RT31P2 and am not getting a ping popup in the administration tab after I reset....No option for ping anywhere in my setup? WWhat am I doing wrong?
This tutorial only applies to the WRTP54G and with slight modification the RTP300.]]> http://www.dslreports.com/forum/remark,21709789 Fri, 09 Jan 2009 12:43:40 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21709762 Phoenix2088 : Try breaking up the first command. Unfortunately I don't think this will work because you said you received errors for each entry but it's worth a try.


]]> http://www.dslreports.com/forum/remark,21709762 Fri, 09 Jan 2009 12:40:25 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21709291 anon : mazilo, thanks for your reply. I understand the linux/unix commands going on in these pings but I don't understand what you mean by:

"you will need to put the ping process in the background"

How do I put it in the background? Would you mind elaborating, please? Thanks.]]> http://www.dslreports.com/forum/remark,21709291 Fri, 09 Jan 2009 11:26:12 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21709186 mazilo :
said by MrVile :

127.0.0.1 &&cd /var/tmp &&wget 192.168.15.100/wr
IIRC, && means logical AND in Linux/Un*x. & means to put the process in background. That said, you will need to put the ping process in the background before the change directory process can be executed. This also applies to both the ping and the change directory processes before the wget process can be executed, and so on.
--
Mazilo always prays for FREEBIES!
US Phone: +1-678-601-0907
UK Phone: +44-703-194-2574
]]> http://www.dslreports.com/forum/remark,21709186 Fri, 09 Jan 2009 11:11:09 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21708163 anon : sean7326, I don't think the methods in this post apply to unlocking the RT31P2. This might help though:

»www.bargainshare.com/index.php?s···p=741181

I have a RT31P2 and a WRTP54G but I haven't tried unlocking the RT31P2 yet. If you're able to unlock yours, let me know.]]> http://www.dslreports.com/forum/remark,21708163 Fri, 09 Jan 2009 07:13:48 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21708152 anon : Phoenix2088, first of of all, that's for reply and helping me out.

To answer your question, yes, I get the "illegal ascii code" error on the first ping entry and the two that follow it. Just to be sure, here's the first line I paste into the ping field after removing the maximum lengths with the Web Developer plugin:

127.0.0.1 &&cd /var/tmp &&wget 192.168.15.100/wr

I even double checked to make sure my computer was set to 192.168.15.100

This may sound stupid but it's almost like I have the 5.01.04 firmware with a hidden revision that blocks any characters in the ping field that aren't numbers or periods.

I appreciate your help.]]> http://www.dslreports.com/forum/remark,21708152 Fri, 09 Jan 2009 07:06:01 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21708064 anon : Im using RT31P2 and am not getting a ping popup in the administration tab after I reset....No option for ping anywhere in my setup? WWhat am I doing wrong?]]> http://www.dslreports.com/forum/remark,21708064 Fri, 09 Jan 2009 06:01:26 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21707580 Phoenix2088 : Are you getting the error at the first ping entry?]]> http://www.dslreports.com/forum/remark,21707580 Fri, 09 Jan 2009 00:54:51 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21707322 anon : The above post refers to the Linksys WRTP54G wireless router. Thanks.]]> http://www.dslreports.com/forum/remark,21707322 Thu, 08 Jan 2009 23:56:11 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21707313 anon : Phoenix2088, I followed your directions carefully but when I get to the Ping part (Step 3: #3) I get the error you see above. When I login to the router using admin/admin, it shows 5.01.04 as my firmware revision. Any ideas? Thanks.
]]> http://www.dslreports.com/forum/remark,21707313 Thu, 08 Jan 2009 23:53:50 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21680560 mazilo :
said by ogdensburg See Profile :

Now my WRTP54G is totally bricked.
You should be able to de-brick your WRTP54G using a USB/Serial-console cable.]]> http://www.dslreports.com/forum/remark,21680560 Sun, 04 Jan 2009 17:23:38 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21677592 ogdensburg : I did the samething, go directly to the hacked firmware without going to 1.0.62 vonage firmware first. Now my WRTP54G is totally bricked.]]> http://www.dslreports.com/forum/remark,21677592 Sat, 03 Jan 2009 23:54:57 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21650974 brtech : Worked for me with an RTP300.

One thing not mentioned is that you either have to unplug any other device other than your PC which is connected to the RTP300, or you need to change the IP address it is using for the commands. The instructions (and the RF file) assumes the PC is 198.162.15.100. Your TFTP server window will tell you what the IP address is.

The illustrations are of the WRTP console. The RTP300 Ping console looks a little different.

On my box, the Admin and user logins don't seem to work, but the voip configuration page is available.

Thanks to all who figured this out]]> http://www.dslreports.com/forum/remark,21650974 Mon, 29 Dec 2008 13:49:45 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21500793 Phoenix2088 :
said by Boxter583 :

I have a RTP 300 and when I get to the end of step 4 it stays blinking. I waited for about and hour and it was still blinking. I repeated the steps twice and the same thing happened. Any suggestions?
Did you make sure to switch out the 1.00.62 WRTP54G firmware originally posted with the RTP300 version from the forth post? ]]> http://www.dslreports.com/forum/remark,21500793 Sat, 29 Nov 2008 12:53:58 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21497570 ogdensburg : Anybody apply tried similar steps (with different firmware) in Vtech IP8100 phone with new firmware?]]> http://www.dslreports.com/forum/remark,21497570 Fri, 28 Nov 2008 15:23:37 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21470870 anon : I have a RTP 300 and when I get to the end of step 4 it stays blinking. I waited for about and hour and it was still blinking. I repeated the steps twice and the same thing happened. Any suggestions?]]> http://www.dslreports.com/forum/remark,21470870 Sat, 22 Nov 2008 23:17:26 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21453782 anon : Thank you Phoenix2088 that worked. I did have to reset to default login 1st but all worked after that.]]> http://www.dslreports.com/forum/remark,21453782 Wed, 19 Nov 2008 19:15:17 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21451150 Phoenix2088 :
said by imagn :

I've tried to modify the firmware with a hex editor but cant seem to find the values you refered to can someone please let me know what i should be doing and how to identify the correct values in hex editor
I know this does not directly answer your question but I have seen several questions pop up regarding the hex edit. I will try and post a modified RTP300 NA firmware in the next few days once I get a chance. ]]> http://www.dslreports.com/forum/remark,21451150 Wed, 19 Nov 2008 10:49:31 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21451146 Phoenix2088 :
said by cape27cod :

Any idea if this will work w/ver 1.00.62 as shipped by Vonage. I don't have an upgrade option in my admin tab to upgrade assume locked out by Vonage.
You should be able to start at Step 5 in the tutorial and use CYT then upgrade to the NA firmware.]]> http://www.dslreports.com/forum/remark,21451146 Wed, 19 Nov 2008 10:48:09 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21450796 anon : Any idea if this will work w/ver 1.00.62 as shipped by Vonage. I don't have an upgrade option in my admin tab to upgrade assume locked out by Vonage. ]]> http://www.dslreports.com/forum/remark,21450796 Wed, 19 Nov 2008 09:30:02 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21447414 anon : I've tried to modify the firmware with a hex editor but cant seem to find the values you refered to can someone please let me know what i should be doing and how to identify the correct values in hex editor]]> http://www.dslreports.com/forum/remark,21447414 Tue, 18 Nov 2008 16:02:46 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G WITH 5.01.04 http://www.dslreports.com/forum/remark,21400955 anon : Works great! Thanks a lot Phoenix2088!!!]]> http://www.dslreports.com/forum/remark,21400955 Sun, 09 Nov 2008 15:55:46 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21393163 Phoenix2088 :
said by misterschaps :

Hi.
I´m having problems unlocking my wrtp54G from vonage.

I´ve followed the process by the book at least 20 times, and all the times, when transferring the file to the router, it reaches very fast about 94% (sometimes 93, sometimes 95), then goes veeeryyyyy slow for a few minutes, and then times out. Over and over, so I can´t get to the next step, which is watching the router installing the software.

Any hint?

THANKS!!

Dave.-
That usually happens when the wireless is still running. Make sure that the wireless is off before performing the firmware update.]]> http://www.dslreports.com/forum/remark,21393163 Fri, 07 Nov 2008 18:06:06 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21392567 anon : Hi.
I´m having problems unlocking my wrtp54G from vonage.

I´ve followed the process by the book at least 20 times, and all the times, when transferring the file to the router, it reaches very fast about 94% (sometimes 93, sometimes 95), then goes veeeryyyyy slow for a few minutes, and then times out. Over and over, so I can´t get to the next step, which is watching the router installing the software.

Any hint?

THANKS!!

Dave.-]]> http://www.dslreports.com/forum/remark,21392567 Fri, 07 Nov 2008 16:10:29 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G WITH 5.01.04 http://www.dslreports.com/forum/remark,21366841 mazilo :
said by Barvinok :

..., in fact, I was among the first to talk to guy who finally booted OpenWRT on WRTP54G and I'm actively working on it using his patches ;)
Were you saying your WRTP54G is running with OpenWRT? If so, that will be great. Perhaps, you guys need to download the Legerity GPLed driver source for the FXS port and start working on it. By any chance, did you know if anyone managed to run the OpenWRT for TI AR7 on a PAP2v2?
--
Mazilo always prays for FREEBIES!
US Phone: +1-678-601-0907
UK Phone: +44-703-194-2574
]]> http://www.dslreports.com/forum/remark,21366841 Mon, 03 Nov 2008 00:03:05 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G WITH 5.01.04 http://www.dslreports.com/forum/remark,21356408 anon : I don't care about FXS, I just need this particular Linksys box to be able to run an ipip tunnel and a couple of VLANs. Just like my other WRT54GS do with FreeWRT. I'm pretty much aware of the situation with OpenWRT and TI AR7-based models, in fact, I was among the first to talk to guy who finally booted OpenWRT on WRTP54G and I'm actively working on it using his patches ;)]]> http://www.dslreports.com/forum/remark,21356408 Fri, 31 Oct 2008 15:50:34 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G WITH 5.01.04 http://www.dslreports.com/forum/remark,21356331 GrauerFuchs : OpenWRT may be capable of running, but it's still very preliminary for this platform. You also won't have any of the phone features at all in OpenWRT. So far, the FXS ports are not yet working on anything but the Linksys firmware.]]> http://www.dslreports.com/forum/remark,21356331 Fri, 31 Oct 2008 15:36:19 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G WITH 5.01.04 http://www.dslreports.com/forum/remark,21354877 anon : Tried CYT 3.5, but still no luck. It too hangs on 'waiting for your device' and nothing happens.
But what I'm actually looking for is the way to flash the box with OpenWRT, not necessarily to fully unlock it. It seems that ping-hack does the trick, and who cares about Admin password if it will be running non-Linksys firmware anyway.
Thanks for the tip though.]]> http://www.dslreports.com/forum/remark,21354877 Fri, 31 Oct 2008 11:02:48 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G WITH 5.01.04 http://www.dslreports.com/forum/remark,21354269 Phoenix2088 : Try using CYT 3.5, the link is on the first page. I personally never had any luck with 4.6.]]> http://www.dslreports.com/forum/remark,21354269 Fri, 31 Oct 2008 09:22:21 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G WITH 5.01.04 http://www.dslreports.com/forum/remark,21353858 anon : I have RTP300 freshly disconnected from Vonage therefore safe to play with. I tried to do according to your guidelines.
So far I was only able to downgrade firmware from 5.xxx to 1.00.62. Logged in to the box, left browser open, then started CYT 4.6 but to no avail -- it simply stays at 'waiting for your device' forever...
Any help? Thanks in advance.]]> http://www.dslreports.com/forum/remark,21353858 Fri, 31 Oct 2008 06:52:38 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21342355 anon : Thanks for this. Just flashed an RTP300 that a friend gave me with no problem.]]> http://www.dslreports.com/forum/remark,21342355 Wed, 29 Oct 2008 01:53:37 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G WITH 5.01.04 http://www.dslreports.com/forum/remark,21308701 urskrishna : Could you please let me know how to change the values using Hex Editor, I've done all the changes until this step, mine is RTP300. I opened this Image file using the hex editor and I can see lot of values, but don't really know how and where to change it, please help
"Use a hex editor and change offset 0x17 from 4D to 4C and offset 0x3B0004 from 85 DA 20 BB to 3B A5 4D DA"]]> http://www.dslreports.com/forum/remark,21308701 Wed, 22 Oct 2008 14:01:43 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21307671 Phoenix2088 :
said by Schrody :

Am I pointing to an ISP in India? (3B A5 4D DA)
That is a hex edit that will allow the router to accept the non-Vonage firmware. Not too sure what you are trying to get at.]]> http://www.dslreports.com/forum/remark,21307671 Wed, 22 Oct 2008 10:54:09 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21307220 anon : Am I pointing to an ISP in India? (3B A5 4D DA)]]> http://www.dslreports.com/forum/remark,21307220 Wed, 22 Oct 2008 09:32:08 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21303148 anon : Thank you! My RTP300 has been collecting dust for years...now I might get some use from it again!]]> http://www.dslreports.com/forum/remark,21303148 Tue, 21 Oct 2008 14:27:59 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21290284 mazilo :
said by Phoenix2088 See Profile :

Unfortunately with 5.01.04, I am unaware of a process that will allow you to view the VoIP/SIP settings when the device is in use with Vonage.
Does anyone have the link to download v5.01.04 firmware for RTP300/WRTP54G/PAP2v2?]]> http://www.dslreports.com/forum/remark,21290284 Sat, 18 Oct 2008 22:03:53 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21287890 Phoenix2088 : You will lose all settings and Vonage will not re-provision the device. This process should only be done with routers that are no longer being used with Vonage. Once the device is unlocked you can use it with any BYOD SIP based VoIP providers.

Unfortunately with 5.01.04, I am unaware of a process that will allow you to view the VoIP/SIP settings when the device is in use with Vonage.]]> http://www.dslreports.com/forum/remark,21287890 Sat, 18 Oct 2008 11:30:19 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21287116 shycharles : I am a newbie in the Voip Unlocking world. You are telling the entire process, step by step marvelously. One thing you miss though is whether the device from Vonage (in my case RTP300) will be opened and we will be able to see the entire page with User id & Password, domain and port OR does this process wash every setting that was made by the provider and once we do it, we will just be able to use this device with other providers and not (or maybe) with Vonage? I understand your concern about legalities, which do not bother me as such. All I want to do it to be able to see the following:
User ID (generally 1+my Vonage phone number)
Password
Domain
Port (generally 5060 or 5061)
My Firmware version is 5.01.04 or maybe 5.01.14, basically it is the latest firmware. My understanding is that this information is contained under the disabled (by Vonage) Voice button on device's page.

Any help, and I will pray for you, your ancestors, and your later generations. ]]> http://www.dslreports.com/forum/remark,21287116 Sat, 18 Oct 2008 03:39:32 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21253318 mazilo :
said by Kar :

Hi, I just got a RTp300 and I am wondering what people are using the RTP300 for after unlocking it. Sorry for the newb question
Use it as your router + VoIP to register to any BYOD VoSPs.]]> http://www.dslreports.com/forum/remark,21253318 Sun, 12 Oct 2008 00:10:24 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21251521 anon : Hi, I just got a RTp300 and I am wondering what people are using the RTP300 for after unlocking it. Sorry for the newb question]]> http://www.dslreports.com/forum/remark,21251521 Sat, 11 Oct 2008 15:43:43 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G WITH 5.01.04 http://www.dslreports.com/forum/remark,21180334 anon : :)This is great !!! I'm a novice network config guy. I just followed step by step the procedure and voila ! Million thanks. It worked great.]]> http://www.dslreports.com/forum/remark,21180334 Sat, 27 Sep 2008 23:37:54 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G WITH 5.01.04 http://www.dslreports.com/forum/remark,21150669 Phoenix2088 :
said by kcallis See Profile :

Once the change is made to unlock a Vonnage RTP300, do I lose all of my setting for the port 1 Vonnage information?
Yes, you will lose all settings. Do not do this procedure with a Vonage box that you are currently using, Vonage will not be able to re-provision it.]]> http://www.dslreports.com/forum/remark,21150669 Mon, 22 Sep 2008 16:09:25 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G WITH 5.01.04 http://www.dslreports.com/forum/remark,21144692 GrauerFuchs :
said by kcallis See Profile :

I am not overly concerned with the TOS... What I am concerned about is that fact that I have an additional port that I could be using in conjunction with my asterisk box, and I have no access to make changes.
Unfortunately, I am stuck with Vonnage for historically reasons, but I really need access to my second port.
You should be concerned about it. When Vonage pushes an update, it will (1) be rejected, or (2) overwrite your settings. They do have the ability to access information on the box, so if they feel you violated the TOS, they'll cancel your account, charge you termination for violation of the TOS, and the whole reason you stayed with them will go up in smoke.]]> http://www.dslreports.com/forum/remark,21144692 Sun, 21 Sep 2008 10:08:47 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G WITH 5.01.04 http://www.dslreports.com/forum/remark,21143645 kcallis : I am not overly concerned with the TOS... What I am concerned about is that fact that I have an additional port that I could be using in conjunction with my asterisk box, and I have no access to make changes.
Unfortunately, I am stuck with Vonnage for historically reasons, but I really need access to my second port.]]> http://www.dslreports.com/forum/remark,21143645 Sat, 20 Sep 2008 23:01:37 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G WITH 5.01.04 http://www.dslreports.com/forum/remark,21141219 mazilo :
said by kcallis See Profile :

Once the change is made to unlock a Vonnage RTP300, do I lose all of my setting for the port 1 Vonnage information?
You should not unlock your device which is currently in service with Vonage. Doing so may violate vonage TOS!]]> http://www.dslreports.com/forum/remark,21141219 Sat, 20 Sep 2008 10:57:23 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G WITH 5.01.04 http://www.dslreports.com/forum/remark,21140562 kcallis : Once the change is made to unlock a Vonnage RTP300, do I lose all of my setting for the port 1 Vonnage information?]]> http://www.dslreports.com/forum/remark,21140562 Sat, 20 Sep 2008 02:56:01 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G WITH 5.01.04 http://www.dslreports.com/forum/remark,21136602 anon : it works, so far this is most perfect solution for vlocked WRTP54G/RTP300. millions thanks.]]> http://www.dslreports.com/forum/remark,21136602 Fri, 19 Sep 2008 12:09:29 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G WITH 5.01.04 http://www.dslreports.com/forum/remark,21133882 Phoenix2088 :
said by asteriskloveerrr :

Hi Phoenix2088, this is wonderful, I'm wondering is this method applying to RTP300 too? thanks for your instruction.
Thanks, no problem. Yes this method will work for the RTP300, but some files need to be substituted. Other than that follow the directions above for the rest of the unlock procedure.

1. Download the following to replace the von10062.bin file contained in the ZIP archive at Step 1 - Part 3. Rename this new file back to von10062.bin. To ensure a proper download use a DOS prompt. The wr and rf files from the ZIP archive are still used for the RTP300.

»httpconfig.vonage.net/rt-11.1.0-···0327.img
or
The DOS prompt will take 5-10 min. The file size is 3,866,632 bytes.

2. This is the RTP300-NA Firmware and will take the place of the firmware at Step 1 - Part 5 and Step 5 - Part 4. Go to the following website, locate and download the firmware. After that you must edit the file for it to run on the RTP300. Use a hex editor and change offset 0x17 from 4D to 4C and offset 0x3B0004 from 85 DA 20 BB to 3B A5 4D DA

»www.linksys.com/servlet/Satellit···ondetail

P.S. - When using the hex editor simply overwrite the file once you are finished.]]> http://www.dslreports.com/forum/remark,21133882 Thu, 18 Sep 2008 21:17:55 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G WITH 5.01.04 http://www.dslreports.com/forum/remark,21133186 anon : Hi Phoenix2088, this is wonderful, I'm wondering is this method applying to RTP300 too? thanks for your instruction.]]> http://www.dslreports.com/forum/remark,21133186 Thu, 18 Sep 2008 19:06:23 EDT Re: [Unlock] TUTORIAL: VONAGE WRTP54G WITH 5.01.04 http://www.dslreports.com/forum/remark,21123085 Phoenix2088 : Step 4: Downgrading Firmware to 1.00.62
1. Ensure that the rf file and von10062.bin from the ZIP archive are in the TFTP32 folder. Power cycle the WRTP54G by unplugging (5 seconds) and replugging the power. Ensure that the wireless is still OFF.

2. Log back into the router and go to Administration >> Ping. Also make sure TFTP32 is running.

3. On the Ping popup, right click >> Web Developer >> Forms >> Remove Maximum Lengths.

Enter the following and click Ping.


Right Click >> Web Developer >> Forms >> Remove Maximum Lengths. Enter the following and click Ping.


Right Click >> Web Developer >> Forms >> Remove Maximum Lengths. Enter the following and click Ping.


You should now see a file transfer in progress under TFTP32. After the firmware has been transferred the power light on the WRTP54G will start to blink if everything is successful. DO NOT INTERRUPT THIS PROCESS. IT MAY TAKE UP TO 2-4 MINUTES TO COMPLETE. WAIT FOR THE POWER LIGHT TO RETURN SOLID AND FOR AN ETHERNET LINK TO BE ESTABLISHED.

Step 5: Unlock with CYT and Load New Firmware
1. Login to the router using admin/admin and leave this window open. Ensure that firmware 1.00.62 has loaded successfully.

2. Open cyt35.exe. Select Option 1. Wait for CYT to provision the WRTP54G. The output for a successful provision will be fairly obvious. This process will take 1-2 minutes.

3. Open a new window and head over to »192.168.15.1/update.html. Login with Admin/Admin or admin/admin.

4. Locate the modified WRTP54G-NA 3.1.17 firmware and initiate the upgrade process. Wait a few minutes and the device will reset itself and take you back to the login page. Username and pass should be admin/admin. Ensure that the firmware is 3.1.17.

Congrats. You now have a fully unlocked WRTP54G!]]> http://www.dslreports.com/forum/remark,21123085 Wed, 17 Sep 2008 00:56:39 EDT [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04 http://www.dslreports.com/forum/remark,21123078 Phoenix2088 : I have noticed that the information for unlocking the WRTP54G is scattered around in various threads. I am going to try and condense all of this information and make it as easy as possible to help unlock a Vonage/Linksys WRTP54G with 5.01.04 firmware. This is a multi-step process that will require downgrading and then finally upgrading to the WRTP54G-NA firmware.

EDIT: Please refer to the 4th post down for unlocking the RTP300.

Disclaimer: I am by no means taking credit for any of this. All of the hard work is credited to jetzhu See Profile, Velund See Profile, the author(s) of CYT, and anyone else I missed. I also do not take any responsibility if you brick your device. Do this procedure at your own risk!

Step 1: Downloads
1. Download Firefox and install the Web Developer Plugin.
»www.mozilla.com/en-US/firefox/
»https://addons.mozilla.org/en-US/firefox/addon/60

2. Download and install TFTP32. This is a Windows based TFTP server that will push the firmware to the device.
»tftpd32.jounin.net/download/Tftp···etup.exe

3. Download the following ZIP file and extract to the folder TFTP32 was installed in (ex. C:\Program Files\TFTP32). It will contain some of the necessary files that will be required for this unlock procedure.
»rapidshare.com/files/145934487/v···zip.html

4. Download CYT.
»/r0/download/1···in32.zip

5. Download the modified WRTP54G-NA 3.1.17 firmware from the following website. Disregard the instructions on that website.
»celiom.googlepages.com/linksys

Step 2: Configure TFTP32
1. Run TFTP32. Click settings, and then setup the base directory. Use the directory you installed the program (ex. C:\Program Files\TFTP32) and make sure the extracted files from the ZIP are in this directory. Change security to none, and set the timeout and max retransmit to 10 and then hit OK.

Step 3: Unlock the Console using Ping Hack
1. Make sure you have downloaded everything from step 1 and ensure the wr file from the ZIP is in the TFTP32 folder. Now disconnect from the internet and connect directly to the WRTP54G making sure the device is also not connected to the internet (ie. pull the Ethernet cord out of the WAN port). Also make sure to disable any Anti-Virus and firewall programs that may be running.

2. Use a paperclip and hard reset the WRTP54G (hold reset for 10-15 seconds). Go to »192.168.15.1 with the username/pass of admin/admin. Go to Wireless and disable it. Once the router restarts go to Administration >> Ping. Also make sure TFTP32 is running.

3. On the Ping popup, right click >> Web Developer >> Forms >> Remove Maximum Lengths.

Enter the following and click Ping.


Right Click >> Web Developer >> Forms >> Remove Maximum Lengths. Enter the following and click Ping.


Right Click >> Web Developer >> Forms >> Remove Maximum Lengths. Enter the following and click Ping.


After a few seconds you should see some information in the output box. Scroll down to the last line and look for CONSOLE_STATE unlocked. If you see this you are good to go. Go to the next post below to continue the unlock procedure.]]> http://www.dslreports.com/forum/remark,21123078 Wed, 17 Sep 2008 00:55:25 EDT