rmshakil
join:2007-01-25
Edmonton, AB
| reply to toro
Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04
Power light start flashing after powering the device and than wirless light comes on(both light get steady)and after 6 seconds or so all the light lights up and restart from power light again. This keep going on and on. I tried to press the reset button more than minute cycle the power with keep the button pressed, left is with internet and also tried connecting PC with it no luck, keep cycling. Hope this will help to understand the problem thanks |
|
toro
join:2006-01-27
Scarborough, ON
 ·TekSavvy Solutions..
1 edit | From my experience (I've seen at leat 3-4 doing the same), that router not bricked. The firmware loads properly if the wireless light goes on.
The voice part however may have gone bad. It may work with a better power adapter (a switched power adapter with regulated voltage).
If another power adapter doesn't work, you can desolder the part labeled Q5 (the voltage regulator for the Legerity chip - see the picture) and it should become stable but will work only as a wireless router (kind of an "unorthodox" solution, but I applied it successfully to 3 or 4 routers so far) |
|
rmshakil
join:2007-01-25
Edmonton, AB
| ok I did try a 2 ampare adapter and found the samw trouble and than I removed Q5 and now it is getting on. Here my question is is there any way to trace the fault or repair the VOIP section?? Can I try upgrading the firmware and see how it behave or this mean the VOIP is dead? |
|
toro
join:2006-01-27
Scarborough, ON | I have no idea. If I knew I would have fixed mine 
I don't think another firmware would be of any help. |
|
ferndock2
join:2007-08-01
Columbia, MD
| reply to rmshakil
I have an RTP300 that was given to me by someone who stopped using Vonage. Everything I've read says I should be able to connect to it at 192.168.15.1 but that doesn't work. The only connection I've been able to make is with a reversal cable directly from my PC to the RTP300 Internet port. It is then that I learn that the RTP300 says its address is 169.254.226.127. When I connect to that address I get a login window but cannot get in by using admin/admin or Admin/Admin or user/user. Instead I get a screen telling me my login doesn't allow me access. Pushing the Reset button, powering off/on, and the combination of the two do nothing. I can't run CYT because it only works with addresses in the 192.168 range. So, how can I talk to this unit and make it take new information? |
|
toro
join:2006-01-27
Scarborough, ON
·TekSavvy Solutions..
| said by ferndock2  :Everything I've read says I should be able to connect to it at 192.168.15.1 but that doesn't work. Power on the router and let it run for 2-3 minutes, then push and hold the reset button for at least 8 seconds (until the lights start flashing). After that, your router should be reset to the factory settings and should have the IP 192.168.15.1 on the LAN ports (unless it's defective). |
|
ferndock2
join:2007-08-01
Columbia, MD
| I did as Toro suggested with negative result. I also gave it 30-second and 1-minute pushes on the reset button. Only one time did this yield a connection that allowed me to reach 192.168.15.1. On that connection I saw the Linksys login page and typed admin/admin. At that point IE7 popped its "remember this password" and by the time I got rid of that IE7 locked up forcing me to restart it. Since, then, no connections. Otherwise, this unit won't give a steady connection indicator light on any of the LAN (Ethernet, yellow) ports. The light will only flash occasionally on the port to which a cable is attached to other equipment. Can't ping the unit. Other suggestions? |
|
toro
join:2006-01-27
Scarborough, ON
·TekSavvy Solutions..
| Does the power light flash for several seconds every once in a while ? If it does, you may be dealing with a defective unit (see »Re: [Unlock] TUTORIAL: VONAGE WRTP54G/RTP300 WITH 5.01.04) |
|
ferndock2
join:2007-08-01
Columbia, MD
| Power light is on steadily. The only times it flashes are when I power down/up or hit reset. After a power up and with the WAN (Internet) port attached to my router, the RTP300's LAN port will turn on and off at a slow rate that infrequently allows me to display the Linksys login screen. I found that by using Admin/Admin to login it says I'm not allowed at that level. Using admin/admin or user/user have not been successful because the LAN port connection doesn't stay up long enough to see a next screen. The LAN port rarely shows a connection greater than 2 seconds. How can I get this unit to give me a steady LAN connection? |
|
toro
join:2006-01-27
Scarborough, ON
·TekSavvy Solutions..
| I've been dealing with dozens of these routers before but I've seen only one with that issue. In that case it was a WRTP54G where the LAN ports were shot but the VoIP and wireless are working fine.
Unfortunately it's a hardware issue and I have no idea how to fix it. |
|
ferndock2
join:2007-08-01
Columbia, MD | Toro, thanks for your input. Anybody else have suggestions? |
|
mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| said by ferndock2 :Toro, thanks for your input. Anybody else have suggestions? Perhaps, you should consider waiting for this NAizer for CYT utility. |
|
ferndock2
join:2007-08-01
Columbia, MD
| Mazilo, I can't use CYT because I can't establish a connection to the RTP300 through its LAN (Ethernet, yellow) ports. Those ports give highly intermittent, very short-term connections. The only data port on the unit that seems to work correctly is the WAN (Ethernet, blue) connection. Either I coax the LAN ports into working or find a way to log into the WAN port to program it. |
|
mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| reply to ferndock2
said by ferndock2 :I did as Toro suggested with negative result. I also gave it 30-second and 1-minute pushes on the reset button. Only one time did this yield a connection that allowed me to reach 192.168.15.1. On that connection I saw the Linksys login page and typed admin/admin. At that point IE7 popped its "remember this password" and by the time I got rid of that IE7 locked up forcing me to restart it. Since, then, no connections. Otherwise, this unit won't give a steady connection indicator light on any of the LAN (Ethernet, yellow) ports. The light will only flash occasionally on the port to which a cable is attached to other equipment. Can't ping the unit. Other suggestions? When you did this process, did you have the WAN port connected to the Internet? If so, try to re-do this process without Internet connection.
--
Mazilo always prays for FREEBIES!
US Phone: +1-678-601-0907
UK Phone: +44-703-194-2574
|
|
ferndock2
join:2007-08-01
Columbia, MD
| I have tried with the WAN both connected and disconnected. As I said in a later post, I was able to get very brief periods of connectivity from the LAN ports that would show me the Linksys login page via 192.168.15.1. All of those happened when the WAN was connected but never when it was disconnected. |
|
mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| said by ferndock2 :As I said in a later post, I was able to get very brief periods of connectivity from the LAN ports that would show me the Linksys login page via 192.168.15.1. If you have the WAN port connected, what will happen if you disconnect the WAN port while you are able to get the LAN connection from your computer? Will the router still stable?
--
Mazilo always prays for FREEBIES!
US Phone: +1-678-601-0907
UK Phone: +44-703-194-2574
|
|
ferndock2
join:2007-08-01
Columbia, MD
| Unfortunately, the intermittent connectivity I get from the LAN ports is so short that have no time to try anything else. I might get a connection for 2 seconds, then it goes away, and it might or might not reconnect. Sometimes it's enough time to type in admin/admin which takes me to the page 192.168.15.1/cgi-dir/webcm where IE7 says it cannot display that page. |
|
mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| said by ferndock2 :Unfortunately, the intermittent connectivity I get from the LAN ports is so short that have no time to try anything else. Do you have another unit of this device that is currently working? If so, try to swap their AC/DC adapter and see if this problem will get resolved. |
|
ferndock2
join:2007-08-01
Columbia, MD | I don't have another RTP300. I do have another 12V 1.5A power supply which I connected. No difference in the RTP300's operation. |
|
ferndock2
join:2007-08-01
Columbia, MD
| I was able to establish a stable connection to the RTP300 LAN port but it required that I have a second computer connected to another of the unit's LAN ports and a fan blowing air into the bottom of the unit. Yes, I'd say the unit is having hardware problems. Once I established the stable connection I was able to login with admin/admin and manipulate any parameters that were allowed. Tried to login with user/tivonpw but that didn't work. Then I tried the CYT Unlocker versions 3.9 and 4.6. Let each of them run multiple times for up to 5 minutes but nothing happened. Recommendations? |
|
