how-to block ads
|
connor2709tx
join:2003-12-08
Burleson, TX
| SpeedStream 5260 Before I go out and buy a new modem/router I thought I would post my efforts to get into the 5260 SpeedStream modem in order to bridge it so that I can use a Linksys WRT54G for wireless connectivity in the home.
I have followed several posts which suggest to set the NIC at 10.0.0.x and subnet 255.255.255.0 and then telnet (Vista) into the modem with 10.0.0.1. I alsways get the "Cannot connect....on port 23.
I just saw a post that you can do the same with the Router on the set up page. I have not tried that as of yet.
I have not flushed the DNS or released the IPCONFIG on the NIC of the Workstation, or tried to isolate the modem to connect with just ....say a laptop NIC (XP Pro) for the tenet session.
Any suggestions would be a great help. | |
|  
graysonf
Premium,MVM
join:1999-07-16
Fort Lauderdale, FL | Re: SpeedStream 5260 I thought the 5260 was a bridge and only a bridge. | |
| connor2709tx
join:2003-12-08
Burleson, TX
| My bad !! I wan to unbridge the modem so that I can use it just as a modem. The post »DSL FAQ »Getting into the SpeedStream 5260 tells how to unbridge the modem.
My problem is that I cannot get into the modem using the above post methods. If I understand the post correctly, when I unbridge the modem I can use the router to gain wi-fi. Hoook up would be destop-router-modem. | |
| |
graysonf
Premium,MVM
join:1999-07-16
Fort Lauderdale, FL
| Re: SpeedStream 5260 I don't think that FAQ section is fully accurate. And you are confused as to what a bridge is.
The mode you want is bridging - so that you can place a router behind it, and that's all this unit can do. There is no such thing as unbridging a device that is only a bridge.
As far as not being able to "get into the modem" either you don't know its IP address or there is no telnet capability in it to begin with. Try a browser, but if you don't know the unit's IP address, that's not going to work either. | |
| | | 
Doctor Olds
I Need A Remedy For What's Ailing Me.
Premium,VIP
join:2001-04-19
1970 442 W30
clubs:
| Re: SpeedStream 5260 said by graysonf  :I don't think that FAQ section is fully accurate. And you are confused as to what a bridge is. The FAQ is accurate, but it is missing vital info as it was taken "completely out of context" from this FAQ group »The Unofficial SpeedStream 5260 ---> 5660 FAQ and if you read the "Pending Feedback" at the bottom of the FAQ the OP posted, it shows that FAQ only applies to the Part Number 060-5660-00X Model 5260 which is in essence a hidden 5660 Router. If the OP has a real 5260 Part Number 060-5260-00X or 060-5262-00X or 060-5263-00X then those Models are truly Bridge/Modems only without any Router features or even IP Addresses.
Below is the correct FAQ section link for a true 5260/5262/5263 instead of the mis-used 5260/5660 Router Hybrid FAQ the OP linked to in error.
Speedstream 5260 FAQs
Regards,
Doctor Olds
--
What’s the point of owning a supercar if you can’t scare yourself stupid from time to time? | |
| connor2709tx
join:2003-12-08
Burleson, TX
| With ipconfig/all I can get the ip address of the modem. It is an outside address that resolves to the the isp. The idea is to convert the modem to translate the packets from phone line to ethernet and hand off to the router wan port.
I have tried the telnet...must be to old to have the interface as it was recieved from SBC about 8 years ago.
So....its off to the net for a new ASDL modem/router.
Thanks for the reply. | |
| |
graysonf
Premium,MVM
join:1999-07-16
Fort Lauderdale, FL
| Re: SpeedStream 5260 ipconfig/all gives you the address of your ethernet adapter, not the modem. It's your public IP because that's where it winds up - on the device behind the bridge - your ethernet adapter.
You have the bridge you need to work with your router - you just don't know what to do with it.
Good luck. | |
| |
Doctor Olds
I Need A Remedy For What's Ailing Me.
Premium,VIP
join:2001-04-19
1970 442 W30
clubs:
| said by connor2709tx :Before I go out and buy a new modem/router I thought I would post my efforts to get into the 5260 SpeedStream modem in order to bridge it so that I can use a Linksys WRT54G for wireless connectivity in the home. There is nothing to access in a true 5260 Bridge Modem. It is already a Bridged Device and ready to work with your Linksys.
said by connor2709tx :I wan to unbridge the modem so that I can use it just as a modem. The post » DSL FAQ » Getting into the SpeedStream 5260 tells how to unbridge the modem. My problem is that I cannot get into the modem using the above post methods. If I understand the post correctly, when I unbridge the modem I can use the router to gain wi-fi. Hoook up would be destop-router-modem. You can't access it as you don't have the Modem that the FAQ is talking about. You are reading a FAQ copied in error from this »The Unofficial SpeedStream 5260 ---> 5660 FAQ »How do I telnet into my modem? entry in the »The Unofficial SpeedStream 5260 ---> 5660 FAQ which is only for 5260 Models with a Part Number of 060-5660-00X. It does not apply to any other 5260 with different Part Numbers.
said by connor2709tx :With ipconfig/all I can get the ip address of the modem. It is an outside address that resolves to the the isp. The idea is to convert the modem to translate the packets from phone line to ethernet and hand off to the router wan port. I have tried the telnet...must be to old to have the interface as it was recieved from SBC about 8 years ago. So....its off to the net for a new ASDL modem/router. You already have a Bridge Modem, you don't need to replace it unless you want to waste more time (and money) chasing a non-issue. All you need is to hook up the Linksys Router to the Speedstream DSL Modem and then hook up your PC to the Linksys Router.
The Linksys has to be setup like the PC that was using the connection before the Linksys was added. If the PC was DHCP then the Linksys WAN setting/Connection Type needs to be setup for DHCP. If the PC was setup with PPPoE then the Linksys needs to be setup for a Connection Type with PPPoE.
Regards,
Doctor Olds
--
What’s the point of owning a supercar if you can’t scare yourself stupid from time to time? | |
| connor2709tx
join:2003-12-08
Burleson, TX
| Thanks graysonf and Dr. Old for pointing out my failure to be able to complete my project.
After reviewing your posts, I am still not able to grasp what to do to use a router (Linksys) and the 5260 modem to gain access to the internet with a wireless laptop.
If one of you could write out detailed instructions, it would be ever so helpful.
Thank you in advance, | |
| connor2709tx
join:2003-12-08
Burleson, TX
| Thank you much. I understand that the Linksys needs to set up like the PC so that it will "reach out" to ma bell and connect like a PC and have the ability to broadcast wireless and via ethernet cable.
I did try that route using the set up page etc on the linksys but could not get a connection to the isp server.
The original pc is set to dhcp so that may be my problem with the linksys. I will revisit the situation later today as this is a setup at my best bud's home.
He has just been released from the hospital......55 days, broke his back and is confined to his special easy chair except for nature calls and to go to bed thus I wanted to setup a wi-fi with my old linksys router so he can surf, email etc.
Thank you again for the straight forward reply Dr. Old.
I will post later with more detail on what I have done to make it work or my attempts to make it work. | |
| |
Doctor Olds
I Need A Remedy For What's Ailing Me.
Premium,VIP
join:2001-04-19
1970 442 W30
clubs:
| Re: SpeedStream 5260 If your PC was set to DHCP, then the Linksys will need to be setup the same way. See image above. | |
| connor2709tx
join:2003-12-08
Burleson, TX | Thanks will do .....My friend Rick had a bunch of company so I will get to it tomorrow.
Thanks again | |
| connor2709tx
join:2003-12-08
Burleson, TX
| Dr. Olds.
Finally got the Linksys Router to bypass the modem and make connection to ATT direct without the ATT software. Prior to following the directions below, I reset the router and did a ipconfig release on the computer. I followed the below directions, which all in all did the same as you suggested, put in the user name and password and select
PPoE. I also turned off the anon requests in the security/fire wall section of the router. The key seems to be the power off and power on cycle listed in Step 5.
Thanks for your help.
How To Set Up PPPoE DSL Connections with a Linksys Router
Question
How do I connect and configure my Linksys Router to use PPPoE DSL service?
Answer
This article describes how to manually configure a Linksys Router for broadband DSL that uses PPPoE (Point-to-Point Protocol over Ethernet) for authentication. For automatic configuration options, please try:
1. Linksys Easy Connect
2. The Linksys Setup Wizard CD-ROM software that came with your Linksys Router. Simply insert this CD-ROM into an online computer before connecting your Linksys Router, and the Wizard will provide step-by-step instructions on how to install and configure your router.
If you are unable to set up your Linksys Router by using one of the above options, use the steps below to manually configure your router.
NOTE: It is recommended that you print this article for offline reference.
STEP 1: Before You Begin
In order to set up your Linksys Router, be sure to first have the following:
1. A Linksys Router.
2. A DSL modem.
3. A working computer that can be wired in directly to the router for initial configuration and testing.
4. Two (2) standard Ethernet network cables. Linksys Routers come with one (1) standard network cable that you can use.
5. The PPPoE DSL username and password assigned by your Internet Service Provider. Depending on the provider, your username format might be similar to username, vzn123456, or an e-mail address (username@isp.net). If you are not sure what your username and password are, contact your Internet Service Provider for more information.
STEP 2: Check Your Internet Connection
Before installing your Linksys Router, it is important to first verify that you can successfully access the Internet by connecting directly to your modem (without your Linksys Router installed).
1. If you are connecting for the first time, follow the instructions provided by your provider to set up your modem and computer for online access.
2. Verify that you are able to access the Internet without any problems. If you are not able to get a connection, contact your Internet Service Provider for assistance.
When you are able to access the Internet using your modem, continue to Step 3 and proceed with the installation of your Linksys Router.
STEP 3: Connect the Hardware
Follow these steps to connect your Linksys Router to your modem and computer.
1. Shut down your computer and unplug the power cords connected to your modem and Linksys Router if they are currently powered on.
2. Disconnect the network cable that connects to the back of your computer.
3. Connect the network cable that you just removed to the Internet port (or WAN port) located on the back of your Linksys Router. Your modem should now be connected to your Linksys Router.
4. Connect a second network cable back into your computer (into the same port that was disconnected in #2).
5. Connect the other end of the second network cable to one of the numbered ports located on the back of your Linksys Router (labeled 1, 2, 3, 4, etc.). Your computer should now be connected to your Linksys Router.
The following diagram shows how your network should be connected. Verify that your connections are correct, and continue to the next step.
6. Plug the included power adapter into the router¡¦s Power port. Then, plug the other end of the power adapter into a nearby electrical outlet to supply power to your router.
7. Turn on your computer.
Do not turn on your modem at this time. Only your router and computer should be turned on for Step 4.
STEP 4: Configure the Router
Follow these steps to configure your Linksys Router.
1. On the computer that is connected to the Linksys Router, open a web browser such as Internet Explorer or Netscape.
2. Type »192.168.1.1 into your browser¡¦s Address or Location bar and click Go or press the [Enter] key on your keyboard. The IP address 192.168.1.1 is the default IP address of Linksys Routers.
3. A user name and password prompt will appear. Leave the user name field blank (empty), and type in admin (lowercase) for the password. The password admin is the default password of Linksys Routers.
NOTE: The following username/password prompt screen will vary by operating system.
4. Once logged in, the router¡¦s web-based Setup utility should load. In the section labeled Internet Connection Type, or WAN Connection Type depending on router model and firmware version, select the PPPoE option on the drop down list.
5. Once PPPoE is selected, enter your PPPoE DSL username and password provided by your Internet Service Provider into the router¡¦s User Name and Password fields. Depending on the provider, your username format might be similar to username, vzn123456, or an e-mail address (username@isp.net). If you are not sure what your username and password are, contact your Internet Service Provider for more information.
NOTE: Be sure to clear the ¡¥Password¡¦ field before entering your account password.
6. If the Keep Alive option is not selected, be sure to select it instead of the ¡¥Connect on Demand¡¦ option. The ¡¥Keep Alive¡¦ option will ensure that your connection stays connected even when it is not in use.
7. Scroll down to the bottom of the page and click on the Save Settings, or Apply button depending on router model, to save your changes.
8. Once your changes are saved, you will be presented with a button to return or you will be returned to the previous page automatically. If prompted, press Continue to return to the router¡¦s Setup page.
9. Close and exit the web browser.
STEP 5: Power Cycle
Follow these steps to power on and off your devices in the correct order.
1. Shut down your computer.
2. Verify that your modem is turned off (either by unplugging the power cord or by using a power switch on the modem).
3. Unplug the power cord from the back of your router and confirm that the front panel lights turn off.
At this stage, all devices (your modem, router, and computer) should be powered off.
4. Wait for about 30 seconds.
5. Plug in the modem¡¦s power cord. If there is an additional power switch required to power on your modem, be sure to use it to apply power and turn on the modem.
6. Observe the indicator lights located on the modem and wait for the lights to stop blinking. A light indicating Power as well as DSL (or Internet, Online, Ready, etc.) should become solid to indicate a connection to your Internet Service Provider. The names of modem lights will vary depending on modem brand and model.
7. Next, plug in the router¡¦s power cord. After a few seconds, the Internet light (or WAN lights) on the front of the router as well as additional lights on your modem should turn on to indicate a connection.
8. Turn on your computer
STEP 6: Check the Connection
Follow these steps to check your connection to your Internet Service Provider.
1. On the computer that is connected to the Linksys Router, open a web browser such as Internet Explorer or Netscape.
2. Type »192.168.1.1 into your browser¡¦s Address or Location bar and click Go or press the [Enter] key on your keyboard. The IP address 192.168.1.1 is the default IP address of Linksys Routers.
3. A user name and password prompt will appear. Leave the user name field blank (empty), and type in admin (lowercase) for the password. The password admin is the default password of Linksys Routers.
4. Once logged in, the router¡¦s web-based Setup utility should load. Click on the Status tab to load the router¡¦s Status page.
NOTE: The location of the Status tab will vary depending on router model and firmware version:
OR
5. In the Status page, look for a section labeled Login Status (or PPPoE Status depending on router model and firmware version). This will indicate the status of the connection.
One of the following statuses may appear:
„X Connecting
If the status repeats with Connecting, your Linksys Router is having problems connecting to your Internet Service provider. Repeat the ¡¥Power Cycle¡¦ steps in Step 5 and try again. Be sure to check for solid status and activity lights on the modem and the Internet light (or WAN lights) on the router. If these lights do not turn on or show any activity, try using different network cables, power cycle all devices as described in Step 5, and try again.
„X Disconnected
If the status shows Disconnected, your Linksys Router was not able to establish a connection to your Internet Service provider. Repeat the ¡¥Power Cycle¡¦ steps in Step 5 and try again. Be sure to check for solid status and activity lights on the modem and the Internet light (or WAN lights) on the router. If these lights do not turn on or show any activity, try using different network cables, power cycle all devices as described in Step 5, and try again.
„X Connected
If the status is Connected, your Linksys Router successfully established a connection to your Internet Service provider and you should be able to access the Internet !
OR
NOTE: If you are not able to access the Internet even with a Connected status, restart your computer and try to access the Internet again.
Troubleshooting
In the router¡¦s Status page, you may be prompted with one of the following error messages:
„X PPPoE Authentication Failed
The PPPoE user name and password you used is incorrect. Repeat the router configuration steps found in Step 4 and verify the spelling and/or format of your login or use another user name and password. Then, perform the ¡¥Power Cycle¡¦ steps in Step 5 and try again.
„X Cannot Connect to PPPoE Server
The router was unable to connect to your Internet Service Provider. Repeat the ¡¥Power Cycle¡¦ steps in Step 5 and try again. Be sure to check for solid status and activity lights on the modem and the Internet (or WAN) lights on the router. If these lights do not turn on or show any activity, try using different network cables, power cycle all devices as described in Step 5, and try again.
„X PPPoE LCP Negotiation Failed
The router was unable to make a connection to your Internet Service Provider. Repeat the router configuration steps found in Step 4 and verify the spelling and/or format of your login or use another user name and password. Then, perform the ¡¥Power Cycle¡¦ steps in Step 5 and try again. | |
| |
Doctor Olds
I Need A Remedy For What's Ailing Me.
Premium,VIP
join:2001-04-19
1970 442 W30
clubs:
| Re: SpeedStream 5260 Resolved said by connor2709tx :Dr. Olds. Finally got the Linksys Router to bypass the modem and make connection to ATT direct without the ATT software. Prior to following the directions below, I reset the router and did a ipconfig release on the computer. I followed the below directions, which all in all did the same as you suggested, put in the user name and password and select PPoE. I also turned off the anon requests in the security/fire wall section of the router. The key seems to be the power off and power on cycle listed in Step 5. Thanks for your help. Glad to hear of your success! 
That was the PPPoE software. Bellsouth calls it FastAccess Connection Manager or some similar name. That is also why it looked like the PC was using DHCP when it was not as Connection Manager sets up it very own LAN connection and does not use the default LAN connection that is set to DHCP, but as I said is not used (until you add the Linksys). And that explains why DHCP did not work in the Linksys as it needed PPPoE as that is all Bellsouth offers customers for a connection type.  So you moved the PPPoE from the PC to the Linksys and that is what it needed to work.
So it was PPPoE on PC to Modem to Bellsouth.
Now it is DHCP on PC to Linksys, Linksys PPPoE to Modem to Bellsouth.
Regards,
Doctor Olds
--
What’s the point of owning a supercar if you can’t scare yourself stupid from time to time? | |
| | | |
|
