Doctor Olds
I Need A Remedy For What's Ailing Me.
Premium,VIP
join:2001-04-19
1970 442 W30
clubs:
| reply to loadmaster
Re: [Home Networking] HELP: After switch to ATT from Covad I can
said by loadmaster  :The router is not Earthlink supplied. Aha, you have a E2E (Ethernet to Ethernet) Router that is not a ADSL Modem also. That is why the VPI/VCI is not there as that is a ATM setting for the DSL side of things. You have to also use a DSL Modem or you cannot connect and the DSL Modem holds the VPI/VCI setting.
DSL Modems have the VPI/VCI either stored in a Table to run though to find the Active VC or they are a single setting supplied and entered during initial configuration for PPP (oE or oA).
Bridge Only DSL Modem
DSL Modem with Router included (2 in 1 Device)
--
What’s the point of owning a supercar if you can’t scare yourself stupid from time to time? |
|
e_dub
franknbeans
Premium,VIP
join:2001-08-12
kickin ass
| reply to loadmaster
What model Zyxel is that? I'm wondering if that Zyxel auto detects the VPI/VCI.
edit:
I don't know what model you have but this is from a P-662HW/HW-D. Go to page 85, section 5.4.
»ftp://ftp2.zyxel.com/P-662HW-D3/user_g···_Ed3.pdf |
|
loadmaster
join:2001-01-10
San Jose, CA
| reply to Doctor Olds
The router is not Earthlink supplied. |
|
Doctor Olds
I Need A Remedy For What's Ailing Me.
Premium,VIP
join:2001-04-19
1970 442 W30
clubs:
| reply to loadmaster
said by loadmaster :Windows has the ability to set the VPI/VCI settings but the Zywall router does not have the ability to set these. HUH? The ZyXEL Routers I have used and even the Earthlink Supplied ZyXEL units all have a settings page for VPI/VCI in the DSL Modem or the PPPoE would not work.
--
What’s the point of owning a supercar if you can’t scare yourself stupid from time to time? |
|
loadmaster
join:2001-01-10
San Jose, CA | reply to Doctor Olds
Windows has the ability to set the VPI/VCI settings but the Zywall router does not have the ability to set these. Only the optional service, login user, password, CHAP/PAP authentication type, and nailed up time. |
|
Doctor Olds
I Need A Remedy For What's Ailing Me.
Premium,VIP
join:2001-04-19
1970 442 W30
clubs:
| reply to loadmaster
said by loadmaster :I removed the service name and reentered the user name. That seemed to work. Thank you O-Wise-One. Your assistance to so many in this forum is indeed appreciated. Yes, Service Name should always be left blank because EL (or their provider aka Covad, AT&T, Qwest) may change the Access Concentrator that you connect to/connect through at any time without warning or notice. That's why it is an optional field and by keeping it blank you can connect to any Access Concentrator that advertises services on the VC (Virtual Circuit) you are configured for. VPI/VCI settings are the two values that create the VC you connect to at the DSLAM.
Regards,
Doctor Olds
--
What’s the point of owning a supercar if you can’t scare yourself stupid from time to time? |
|
loadmaster
join:2001-01-10
San Jose, CA |  reply to Doctor Olds
I removed the service name and reentered the user name. That seemed to work. Thank you O-Wise-One. Your assistance to so many in this forum is indeed appreciated. |
|
Doctor Olds
I Need A Remedy For What's Ailing Me.
Premium,VIP
join:2001-04-19
1970 442 W30
clubs:
| reply to loadmaster
Check your login details. You have to use the full email address "username@earthlink.net" with your password. In older days, they used a "ELK/" prefix in front of the email address that has been discontinued and some older systems they allowed only the username without the "@Earthlink.net" or "@Mindspring.com" Domain suffix that is now required. Can't think of anything else unless you added a "service name" which is supposed to be left blank on Earthlink DSL.
--
What’s the point of owning a supercar if you can’t scare yourself stupid from time to time? |
|
loadmaster
join:2001-01-10
San Jose, CA |  [Home Networking] HELP: After switch to ATT from Covad I cannot
They switched me from Covad to ATT on Friday. I can connect from my laptop but not from my Zwall 2+ router. The configuration has worked for years. How do I connect through ATt? |
|
