Cisco 1701 w/ WIC1-ADSL problem-Any Help will be appreciated

Author

All Replies

kulmak3

join:2002-01-26
San Jose, CA

Cisco 1701 w/ WIC1-ADSL problem-Any Help will be appreciated

I have a DSL Extreme with DHCP account. It has been running on an old speedstream since I set the account up with no problems. I am wanting to configure a Cisco 1701 with a WIC1-ADSL modem. It looks like I am communicating with DSLExtreme but am not getting an IP address.

Here is the output from my putty session with 'debug atm events' on (the config follows the debug lines)

Smart Init is enabled
smart init is sizing iomem
ID MEMORY_REQ TYPE
MainBoard 0X00027A80 1701
0X000F3BB0 public buffer pools
0X00211000 public particle pools
VPN 0X00030C0C VPN Module Buffers
0X002E 0X0001B800 Card in slot 0
0X0007 0X00029400 Card in slot 1
TOTAL: 0X003A1E3C

If any of the above Memory Requirements are "UNKNOWN", you may be using an unsupported
configuration or there is a software problem and system operation may be compromised.

Allocating additional 7845725 bytes to IO Memory
Mem allocated: 89008743 bytes; IOMem allocated: 11654553 bytes

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706

Cisco IOS Software, C1700 Software (C1700-K9O3SY7-M), Version 12.4(25a), RELEASE SOFTWARE (fc2)
Technical Support: »www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Fri 22-May-09 20:20 by prod_rel_team

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
»www.cisco.com/wwl/export/crypto/···qrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

Cisco 1701 (MPC860P) processor (revision 0x201) with 86922K/11382K bytes of memory.
Processor board ID FOC10101NRL (2277953424), with hardware revision 0000
MPC860P processor: part number 5, mask 2
1 FastEthernet interface
1 ISDN Basic Rate interface
1 ATM interface
1 Virtual Private Network (VPN) Module
32K bytes of NVRAM.
32768K bytes of processor board System flash (Read/Write)

Press RETURN to get started!

*Mar 1 00:00:05.307: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:06.399: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:13.419: %VPN_HW-6-INFO_LOC: Crypto engine: em 3 State changed to: Initialized
*Mar 1 00:00:13.423: %VPN_HW-6-INFO_LOC: Crypto engine: em 3 State changed to: Enabled
*Mar 1 00:00:22.575: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:23.691: %LINEPROTO-5-UPDOWN: Line protocol on Interface NVI0, changed state to up
*Mar 1 00:00:33.027: %LINK-5-CHANGED: Interface BRI0, changed state to administratively down
*Mar 1 00:00:33.147: %SYS-5-CONFIG_I: Configured from memory by console
*Mar 1 06:08:38.859: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0, changed state to down
*Mar 1 06:08:40.067: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1700 Software (C1700-K9O3SY7-M), Version 12.4(25a), RELEASE SOFTWARE (Router>fc2)
Technical Support: »www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Fri 22-May-09 20:20 by prod_rel_team
*Mar 1 06:08:40.111: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start

Router>en
Password:

*Mar 1 06:09:20.139: %LINK-3-UPDOWN: Interface ATM0, changed state to up
*Mar 1 06:09:21.139: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to up

Router#show ip interface brief

Interface IP-Address OK? Method Status Protocol
ATM0 unassigned YES NVRAM up up
ATM0.1 unassigned YES DHCP up up
BRI0 unassigned YES NVRAM administratively down down
BRI0:1 unassigned YES unset administratively down down
BRI0:2 unassigned YES unset administratively down down
FastEthernet0 192.168.1.1 YES NVRAM up up
NVI0 unassigned NO unset up up

Router#debug atm events

ATM events debugging is on

Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int
Router(config)#interface atm 0.1
Router(config-subif)#shut
Router(config-subif)#exit
Router(config)#
*Mar 1 06:09:53.043: dslsar_1a_teardown_vc(ATM0): vc:1 vpi:0 vci:35
*Mar 1 06:09:53.043: ATM(): IP multicast cache invalidated for ATM0.1int
Router(config)#interface atm 0
Router(config-if)#no shut
Router(config-if)#shut
Router(config-if)#

*Mar 1 06:10:03.035: ATM0 dslsar_1a_shutdown: state=6
*Mar 1 06:10:03.035: dslsar disable ATM0
*Mar 1 06:10:03.035: DSL: SET: [DMTDSL_SHOWTIME -> DMTDSL_STOP]
*Mar 1 06:10:03.039: Resetting ATM0
*Mar 1 06:10:03.239: DSL: SM: [DMTDSL_SHOWTIME -> DMTDSL_STOP]
*Mar 1 06:10:03.739: DSL(ATM0): Sent command 0x4
*Mar 1 06:10:04.287: DSL: Received response: 0x25
*Mar 1 06:10:04.291: DSL(ATM0): Connection closed
*Mar 1 06:10:05.035: %LINK-5-CHANGED: Interface ATM0, changed state to administratively down
*Mar 1 06:10:05.035: dslsar_atm_lineaction(ATM0): state=6
*Mar 1 06:10:06.035: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to down

Router(config-if)#no shut
Router(config-if)#

*Mar 1 06:10:24.367: ATM0 dslsar_1a_reset: PLIM type is 18, Rate is 768Mbps
*Mar 1 06:10:24.367: ATM0 dslsar_1a_shutdown: state=4
*Mar 1 06:10:24.367: dslsar disable ATM0
*Mar 1 06:10:24.367: DSL: SET: [DMTDSL_STOP -> DMTDSL_INIT]
*Mar 1 06:10:24.367: Resetting ATM0
*Mar 1 06:10:24.371: dslsar_1a_config(ATM0)
*Mar 1 06:10:24.371: dslsar_1a_enable(ATM0)
*Mar 1 06:10:24.371: ATM0: dslsar_init
*Mar 1 06:10:24.383: ATM0 dslsar_MatchSARTxToLineSpeed(): usbw 768, clkPerCell 19504 prev_clkPerCell 9702
*Mar 1 06:10:24.383: ATM0 dslsar_MatchSARTxToLineSpeed(): Changing line speed from fast to slow
*Mar 1 06:10:24.491: ATM0 dslsar_update_us_bandwidth(): upstream bw =768 Kbps
*Mar 1 06:10:24.991: (ATM0)1a_enable: delay activation of vcd=1, vc=0x836F5504
*Mar 1 06:10:24.995: DSL: SM: [DMTDSL_STOP -> DMTDSL_INIT]
*Mar 1 06:10:24.995: DSL: SM: [DMTDSL_INIT -> DMTDSL_DLOAD_1]
*Mar 1 06:10:24.999: DSL: Downloading ASW_init_3_8_131.bin
*Mar 1 06:10:25.011: DSL:(ATM0) Downloaded 5 blocks... Finished!
*Mar 1 06:10:25.011: DSL(ATM0): Sent command 0x14
*Mar 1 06:10:26.367: %LINK-3-UPDOWN: Interface ATM0, changed state to down
*Mar 1 06:10:26.367: dslsar_atm_lineaction(ATM0): state=0
*Mar 1 06:10:28.919: DSL: Received response: 0x80
*Mar 1 06:10:28.919: DSL: SM: [DMTDSL_DLOAD_1 -> DMTDSL_DLOAD_2]
*Mar 1 06:10:29.311: DSL: Downloading ASW_R3_8_131.bin
*Mar 1 06:10:29.539: DSL(ATM0): Downloaded 100 blocks
*Mar 1 06:10:29.771: DSL(ATM0): Downloaded 200 blocks
*Mar 1 06:10:29.999: DSL(ATM0): Downloaded 300 blocks
*Mar 1 06:10:30.231: DSL(ATM0): Downloaded 400 blocks
*Mar 1 06:10:30.463: DSL(ATM0): Downloaded 500 blocks
*Mar 1 06:10:30.691: DSL(ATM0): Downloaded 600 blocks
*Mar 1 06:10:30.919: DSL(ATM0): Downloaded 700 blocks
*Mar 1 06:10:31.151: DSL(ATM0): Downloaded 800 blocks
*Mar 1 06:10:31.383: DSL(ATM0): Downloaded 900 blocks
*Mar 1 06:10:31.611: DSL(ATM0): Downloaded 1000 blocks
*Mar 1 06:10:31.839: DSL(ATM0): Downloaded 1100 blocks
*Mar 1 06:10:32.071: DSL(ATM0): Downloaded 1200 blocks
*Mar 1 06:10:32.299: DSL(ATM0): Downloaded 1300 blocks
*Mar 1 06:10:32.343: DSL:(ATM0) Downloaded 1317 blocks... Finished!
*Mar 1 06:10:32.343: DSL(ATM0): Sent command 0x14
*Mar 1 06:10:34.351: set tx_gain_offset to 0
*Mar 1 06:10:34.351: set rx_gain_offset to 0
*Mar 1 06:10:34.351: set target_noise_margin_offset to 0
*Mar 1 06:10:34.351: set max_bits_tone_limit to 14
*Mar 1 06:10:34.351: changed current state to do open!!
*Mar 1 06:10:34.355: DSL: SM: [DMTDSL_DLOAD_2 -> DMTDSL_DO_OPEN]
*Mar 1 06:10:34.355: DSL: Send ADSL_OPEN command.
*Mar 1 06:10:34.359: DSL(ATM0): Using subfunction 0x15
*Mar 1 06:10:34.359: LOCAL:Max noise margin for power cutoff 31
*Mar 1 06:10:34.359: DSL(ATM0): Sent command 0x3
*Mar 1 06:10:36.859: DSL(ATM0): 1: Modem state = 0x8
*Mar 1 06:10:39.359: DSL(ATM0): 2: Modem state = 0x8
*Mar 1 06:10:41.859: DSL(ATM0): 3: Modem state = 0x8
*Mar 1 06:10:44.359: DSL(ATM0): 4: Modem state = 0x8
*Mar 1 06:10:46.859: DSL(ATM0): 5: Modem state = 0x8
*Mar 1 06:10:49.359: DSL(ATM0): 6: Modem state = 0x10
*Mar 1 06:10:51.859: DSL(ATM0): 7: Modem state = 0x10
*Mar 1 06:10:54.359: DSL(ATM0): 8: Modem state = 0x10
*Mar 1 06:10:56.859: DSL(ATM0): 9: Modem state = 0x10
*Mar 1 06:10:57.479: DSL: Received response: 0x24
*Mar 1 06:10:57.479: DSL: Showtime!
*Mar 1 06:10:57.479: DSL(ATM0): Sent command 0x11
*Mar 1 06:10:57.483: DSL: Received response: 0x61
*Mar 1 06:10:57.483: DSL: Read firmware revision 0x1A04
*Mar 1 06:10:57.483: DSL(ATM0): Sent command 0x31
*Mar 1 06:10:57.491: DSL: Received response: 0x12
*Mar 1 06:10:57.491: DSL(ATM0): operation mode 0x0002
*Mar 1 06:10:57.491: DSL(ATM0): Sent command 0x33
*Mar 1 06:10:57.495: DSL: Received response: 0x16
*Mar 1 06:10:57.495: DSL(ATM0): Far End ITU Country Code 0x00
*Mar 1 06:10:57.495: DSL: Far End ITU Vendor ID
*Mar 1 06:10:57.495: DSL: Far End ITU Vendor ID Specific 0x0000
*Mar 1 06:10:57.495: DSL: Far End ITU Vendor STD Number 0x0001
*Mar 1 06:10:57.495: DSL(ATM0): Sent command 0x32
*Mar 1 06:10:57.503: DSL: Received response: 0x14
*Mar 1 06:10:57.503: DSL(ATM0): Near End ITU Country Code 0x00
*Mar 1 06:10:57.503: DSL: Near End ITU Vendor ID ALCB
*Mar 1 06:10:57.503: DSL: Near End ITU Vendor ID Specific 0x0000
*Mar 1 06:10:57.503: DSL: Near End ITU Vendor STD Number 0x0001
*Mar 1 06:10:57.503: ATM0 dslsar_MatchSARTxToLineSpeed(): usbw 768, clkPerCell 19504 prev_clkPerCell 19504
*Mar 1 06:10:57.503: ATM0 dslsar_update_us_bandwidth(): upstream bw =768 Kbps
*Mar 1 06:10:57.503: DSL: SM: [DMTDSL_DO_OPEN -> DMTDSL_SHOWTIME]
*Mar 1 06:11:06.647: dslsar_periodic: ENABLING DSLSAR
*Mar 1 06:11:06.655: (ATM0)1a_enable: delay activation of vcd=1, vc=0x836F5504
*Mar 1 06:11:08.139: ATM0 dslsar_verify_tsc_write: Read Verification failed
*Mar 1 06:11:17.139: ATM0 dslsar_verify_tsc_write: Read Verification failed
*Mar 1 06:11:27.139: dslsar enable ATM0
*Mar 1 06:11:27.139: ATM0: dslsar_bringup_interface: Interface and atm_db flags are UP
*Mar 1 06:11:29.139: %LINK-3-UPDOWN: Interface ATM0, changed state to up
*Mar 1 06:11:29.139: dslsar_atm_lineaction(ATM0): state=4
*Mar 1 06:11:30.139: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to up

Router(config-if)#exit
Router(config)#int
Router(config)#interface atm 0.1
Router(config-subif)#no shut
Router(config-subif)#

*Mar 1 06:11:47.147: dslsar_txRingParamInit_and_tcqSetup(): default tx-ring setting is selected for vpi/vci = 0/35
*Mar 1 06:11:47.147: ATM0:dslsar_init_tx_chan_desc_per_vc, vcd = 1, addr = 0x00011040, size = 64
*Mar 1 06:11:47.151: ATM0 dslsar_vc_setup: vcd 1
*Mar 1 06:11:47.151: CONFIGURING(ATM0) VC 1 (0/35) IN TX SCHEDULE TABLE SET 1
*Mar 1 06:11:47.151: (ATM0)Forcing Peakrate and Avgrate to: 768
*Mar 1 06:11:47.151: (ATM0)Requested QoS: Peakrate = 768, Avgrate = 768, Burstsize =0
*Mar 1 06:11:47.151: (ATM0)Configuring VC 1: slot 0 in TST 5
*Mar 1 06:11:47.151: (ATM0) SUCCESSFUL CONFIGURATION OF VC 1 (0/35), QOS Type 4
*Mar 1 06:11:47.151: dslsar_setup_cos(ATM0): vc:1 wred_name:- max_q:0
*Mar 1 06:11:47.151: ATM0: vcd = 1, max_tx_time = 2793

Router(config-subif)#
Router(config-subif)#exit
Router(config)#exit
Router#show run

*Mar 1 06:12:06.283: %SYS-5-CONFIG_I: Configured from console by consolerun

Building configuration...

Current configuration : 1280 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
enable secret xxxxxxx
enable password xxxxxxx
!
no aaa new-model
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
no ip routing
!
no ip cef
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
!
interface ATM0
no ip address
no ip route-cache
no atm ilmi-keepalive
dsl operating-mode auto
!
interface ATM0.1 point-to-point
ip address dhcp
ip nat outside
ip virtual-reassembly
no ip route-cache
pvc 0/35
encapsulation aal5snap
!
interface BRI0
no ip address
encapsulation hdlc
no ip route-cache
shutdown
!
interface FastEthernet0
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
no ip route-cache
speed auto
full-duplex
!
ip forward-protocol nd
ip http server
no ip http secure-server
!
ip nat inside source list 1 interface ATM0.1 overload
!
access-list 1 remark INSIDE_IF=FastEthernet0
access-list 1 remark SDM_ACL Category=2
access-list 1 permit 192.168.1.0 0.0.0.255
!
control-plane
!
line con 0
line aux 0
line vty 0 4
password xxxxxxxx
login
!
end


Friday, 27-Nov 09:10:02	Terms of Use \| Privacy Policy \| Hosting by www.nac.net - DSL,Hosting & Co-lo \| feedback \| contact over 10 years online! © 1999-2009 dslreports.com. page compression OFF