drahnier
join:2003-02-11
germany | reply to baila
Re: ZyXEL NBG-460N
ZyXEL have just posted a new firmware: V3.60(AMX.5). Apparently, it features a new WLAN driver. For the first time, I can now use 802.11n without experiencing frequent disconnects. |
|
csayers
join:2006-08-21
canada
| downloaded and installed the NGB-460N AMX.5 on my x550N which has been gathering dust due to disconnects. I am happy to say that the new firmware has been stable for 10 hours with one VPN tunnel and SIP phone running on it.
search V3.60(AMX.5) for download site it is not on X550N page yet.
Note that when upgrading through the router page it appears to do nothing, just leave it on the page as it will take like 2-5 minutes before it starts to upload the .bin file.
I will report back in a few days as the previous firmware couldnt go more than 2 days before the wireless quit and the WAN went down. |
|
Dandemon
join:2006-04-05
Australia
| For some reason I can't download the linked file from the Zyxel worldwide site. Could some kind soul please grab the release notes off the download and post the changes up here? Thanks in advance...
»www.zyxel.com/web/support_downlo···BG-460N# |
|
drahnier
join:2003-02-11
germany | reply to drahnier
Unfortunately, even with the new firmware I experience disconnects when enabling N mode, however, they happen far less frequent. |
|
csayers
join:2006-08-21
canada
| reply to csayers
Well it has been 10 days with the new 460 firmware loaded on my 550N, Not one drop, no disconnects for my VOIP box and one IPSEC tunnel running. Fantastic, finally This box lives up to the Zyxel name. One last problem to figure out and it is perfect. I cannot figure out how to let HTTPS and HTTP reach my Windows home server box. Using port forwarding doesn't seem to work, Anyone know any tricks? The firmware is different than my Zywall 35 and I cannot get this X550N to let my HTTP or HTTPS in. |
|
Dandemon
join:2006-04-05
Australia
| csayers, I'm not sure you can specify firewall blockage by the kind of traffic.
On another topic... In Bandwidth Management, can you check the upload speed menu and see what speed setting options it gives you? Is it only MB/Sec or KB/Sec? I need to check whether they did what I asked... |
|
csayers
join:2006-08-21
canada
| Dandemon,
The first page shows Mbps but I think it was that way in the March firmware, I am not using the BWM feature but it still shows the VOIP class as using TCP when it should be UDP.
Also Dan, I want to open via NAT a port , not block the HTTP and HTTPS Traffic, is that more clear? Any ideas? |
|
Simonvetterl
join:2009-10-16
8426
| reply to baila
Hi
I also use NBG-460. Also I connect one Linksys PAP2 on it. But I have the problem, the nobody can reach me from outside. I have to set up port forwarding with udp. But how and where can I do it? And wich ports schould I take? port Nr 5060?
Kind Regards. Simon |
|
Dandemon
join:2006-04-05
Australia | I had a PAP2 connected to mine too, Simon. The trick is to enable PnP in the router and let the PAP2 navigate its own way through the firewall. Don't open up any ports or try to second-guess the router - you'll just get in the way! |
|
Simonvetterl
join:2009-10-16
8426 | reply to baila
Hi
Do You know, where I can set Re-Authentication on my PAP2?
Kind Regards. |
|
