Bell Canada → Re: Fibe 25 upload speed decreased after install

How do you enable telnet on the Sagemcom via http manually?

Someone on the forums made a program for it

Thank you did not know about this program

Enabled the telnet and can connect but which command gets me my line stats?

I think there was two ways

1) on the first telnet screen you should be able to type sysutil xdslmon (this may be more useful to OP since it shows estimated attainable upload rate too)

2) type system shell
vdsl
enter password: superikanos (turns out to use the default chipset pw)
hit 11 to Request Extended Port Status
ctrl^c to exit

PS if anyone from Bell's management reads this. Next time you spend millions for a custom product you should request these self-diagnostics are included in the web GUI instead of making the little guy jump through hoops to get them. I saw other ISPs using Sagem with much more elaborate options in the GUI. It's a bit ridiculous why you would exclude something so simple with no harm.

1st way gives bad command but 2nd way works.

try system shell and then sysutil xdslmon

That one worked.

Thank you!

Hey Guys, i'm trying to pull my line stats and i'm getting the following.
any idea why my stats are not coming up? by the way im on FTTH

HomeGateway> system shell
Temporary setting log_level off

BusyBox v1.01 (2005.09.07-07:38+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

# sysutil xdslmon

xDSL port is not in showtime
#

FTTH does not use the dsl modem, it is straight ethernet.

Here is what I get with the xdslmon:

# sysutil xdslmon

Line Status : Port is in Showtime
Mode : 0x100000 (VDSL2 Profile 8A )
Upstream Payload Rate : 4032 kbps
Downstream : 26040 kbps
=================================================
DIAG Info:
=================================================
Attenuation ( dB ) : 28.4 0.00 (FE LATNpb-0)
39.30 (FE LATNpb-1)
0.00 (FE LATNpb-2)
0.00 (FE LATNpb-3)
0.00 (FE LATNpb-4)
SNR margin ( dB ) : 18.9 0.00 (FE SNRMpb-0)
5.50 (FE SNRMpb-1)
0.00 (FE SNRMpb-2)
0.00 (FE SNRMpb-3)
0.00 (FE SNRMpb-4)
US Aggregate Power : 8.0 dbm
DS Attainable Data Rate: 49352 kbps
US Attainable Data Rate: 4112 kbps
HEC counter : HEC_F:0
HEC_S:0
CRC counter : CRC_F:0
CRC_S: 0

I posted in the direct forum and someone said they changed some settings on my profile. Seems a bit worse now comparing the line stats:

Extended Port Status
=================
Bme: 1 Port: 1
Downstream line rate: 30252 kbps
Upstream line rate: 4656 kbps
Bearer0 Downstream payload rate: 0 kbps
Bearer1 Downstream payload rate: 26040 kbps
Bearer0 Upstream payload rate: 0 kbps
Bearer1 Upstream payload rate: 4032 kbps
Downstream attainable payload rate: 49352 kbps
Downstream attainable line rate: 60208 kbps
Downstream Training Margin: 19.6 dB
Downstream Line Protection (Bearer1 Path): 0.0 DMT Symbols
Upstream Line Protection (Bearer1 Path): 0.0 DMT Symbols
Near-end ITU Vendor Id: 0xb500494b4e530200
Far-end ITU Vendor Id: 0xb500494b4e530100
Downstream delay: 7.4 ms
Upstream delay: 0.0 ms
Tx total power 8.0 dbm
FE Tx total power 14.3 dbm
VDSL Estimated Loop Length : 2371 ft
G.Hs Estimated Near End Loop Length : 2055 ft
G.Hs Estimated Far End Loop Length :2264 ft
Current framing mode: 0x10 EFM
Bandplan Type...........: 2
No. of Upstream Bands...: 1
No. of Downstream Bands.: 2
Line Type: 0x00100000 VDSL2 Profile 8A
Downstream FFT Protection (Bearer1 Path): 1.0 DMT Symbols
Upstream FFT Protection (Bearer1 Path): 0.0 DMT Symbols
Upstream Line Attenuation: NA (Only for ADSL1 & T1.413)
Upstream SNR Margin: NA (Only for ADSL1 & T1413)
Upstream Retransmission status: Disabled
Downstream Retransmission status: Disabled

@badabingo What xtlee said, those tools are just for DSL.

@xtlee It looks like he just added interleave. Did Bell say they will try another pair?

They said thy could open another ticket with the Test Center.