 MarshalPremium
join:2003-11-01
Montreal
1 edit | FTTH - Remplacer Connection Hub par... Bonsoir,
je sais que c'set deja venu sur le sujet.. mais j'ai besoin "d'aide"
Je suis sur FTTH.. Jai reussi a enlever le "Connection Hub"... j'ai mis une box avec pfsence, configure les 2 vlan sur le wan.. tout marche (internet, IPTV..), mais j'ai un petit glitch..
J'aimerais donc, si qqun connait assez bien pfSence, qu'il me fasse signe.. J'ai quelques question a poser  |
|
MarshalPremium
join:2003-11-01
Montreal | Voici un "update".... c'est en anglais pcq j'ai poste sur les forums de pfsence, mais surement ici qqun connait.. ?
Tonight, with pfsence, I was able to setup the wan connection to use both vlan, and get them working. I create a wan interface named WANINET for my pppoe connection, and WANIPTV for the Iptv connection.
I added, in the routes, a route for the multicast (224.0.0.0/4) and 10.0.0.0/8 network to go through the WANIPTV port.. I also setted up the IGMP proxy, and added 2 rules in the FW to allow traffic (224.0.0.0/8 and 10.0.0.0/4) to the WANIPTV network..
My internet connection work, and IPTV too.. im able to watch tv, all channels.. BUT.. only one thing.. after 10 seconds, the TV tell me that there is a loss of signal. I change channel and it come back, for another 10 seconds..
Je suis donc jamme la..
--
Rogers - iPhone 4s 32gb |
|
kovy
join:2009-03-26
kudos:8 | reply to Marshal
said by Marshal:Bonsoir,
je sais que c'set deja venu sur le sujet.. mais j'ai besoin "d'aide"
Je suis sur FTTH.. Jai reussi a enlever le "Connection Hub"... j'ai mis une box avec pfsence, configure les 2 vlan sur le wan.. tout marche (internet, IPTV..), mais j'ai un petit glitch..
J'aimerais donc, si qqun connait assez bien pfSence, qu'il me fasse signe.. J'ai quelques question a poser
Maybe it's a MTU setting issues. |
|
 Glen1These Are The Good Ol' Days.Premium,MVM
join:2002-05-24
GTA Canada
kudos:7 | reply to Marshal
It could be an encryption issue...starts up again after 10 seconds? |
|
MarshalPremium
join:2003-11-01
Montreal
1 edit | as soon I change channel it continue (on the new channel for sure)
I did a capture log, and i cant seem to find what is causing that |
|
| En fait si sa dure seulement 10 secondes c'est que ton Multicast n'est pas ou est mal activé. En tant normal FibeTV envoie quelques secondes en unicast (au terminal qui fait la demande seulement) et ensuite il met la box dans un multicast (tous les terminaux concerné reçoivent le même vidéo les voisins inclus).
Donc il faudrait que tu valides les paramètres relié au Multicast dans ton réseau. |
|
MarshalPremium
join:2003-11-01
Montreal | Dac.. mais, cest ce que je demande.. un peu d'aide
--
Rogers - iPhone 4s 32gb |
|
| reply to Marshal
je pense que sur certaine switch managed tu doit activer le multicast manuelement. si sa peux aider |
|
MarshalPremium
join:2003-11-01
Montreal | reply to Marshal
Pas de switch managed. |
|
|
|
| reply to Marshal
I cant read french but I can provide some insight into the original ops observations.
I dont think it's encryption.
I think something in your setup is not allowing multicast through properly.
When you first access a channel stream, the stream comes through in unicast. Anywhere from 10-45 seconds later it will swap to multicast. Something is happening that is not allowing the hand off from unicast to multicast on your fibetv channel stream.
sounds like you've got some more configuring to do.
--
Opinions and ideas expressed in my post are my own and in no way represent those of Bell Canada Enterprises, Bell Canada, Bell TV, Bell Internet, Bell Mobility, Bell Technical Solutions, Expertech, or any other partners under the BCE umbrella. |
|
