| reply to bbear2
Re: connection issues the modem is hardwired to the NID and no filters installed. Seeing alot of CRC errors causing the reset.
Downstream Upstream
Time Line Rate Max1 Max2 Max3 Mgn1 Mgn2 Attn Pwr CRCs FECs INP DLY Rate Max Mgn Attn Pwr CRCs FECs Mode Vendor State Exit Code Echo VCXO Rx Gain INC Tones
2013/01/03 08:12:41 PST 1 6016 6412 3840 4396 7.3 -2.0 37.8 19.8 11390 0 0.00 0.25 512 524 6.0 31.5 12.4 2508 3538 G.DMT Annex A Infineon 230/105 ERR_HI_BER_LIMIT -11.2 -21.5 24.4 17
2013/01/03 09:23:11 PST 1 5824 5836 5872 5872 6.0 6.0 37.9 19.8 711 0 0.00 0.25 512 524 7.0 31.5 12.4 61 52 G.DMT Annex A Infineon 230/105 ERR_LOS_LIMIT -15.5 -23.1 25.4 0
2013/01/03 12:07:46 PST 1 6016 6540 6596 6596 7.9 8.0 35.6 19.8 905 0 0.00 0.25 768 844 8.0 31.5 12.4 29 0 G.DMT Annex A Infineon 230/105 IDLE_REQUEST -14.3 -22.9 22.5 0
2013/01/03 15:03:21 PST 1 6016 6564 4528 5160 8.0 -1.0 35.4 19.8 19983 0 0.00 0.25 768 792 7.0 31.5 12.4 2274 2139 G.DMT Annex A Infineon 230/105 ERR_HI_BER_LIMIT -14.1 -23.3 23.0 40
2013/01/03 15:21:27 PST 1 6016 6236 4684 5604 6.7 -3.0 35.3 19.8 10680 0 0.00 0.25 768 808 7.0 31.5 12.4 5024 4994 G.DMT Annex A Infineon 230/105 ERR_HI_BER_LIMIT -13.7 -23.4 20.9 28
2013/01/03 16:00:29 PST 1 6016 6172 6444 6444 6.5 1.0 35.0 19.8 10748 0 0.00 0.25 768 808 7.0 31.5 12.4 28 28 G.DMT Annex A Infineon 230/105 ERR_HI_BER_LIMIT -13.5 -22.9 22.6 17
2013/01/03 16:55:26 PST 1 6016 6456 6152 6152 7.5 -3.0 35.1 19.8 20493 0 0.00 0.25 768 792 7.0 31.5 12.4 2820 2787 G.DMT Annex A Infineon 230/105 ERR_HI_BER_LIMIT -13.7 -23.6 21.2 49
2013/01/03 17:27:04 PST 1 4928 4952 2820 3396 6.1 -3.0 35.3 19.7 10642 0 0.00 0.25 768 800 7.0 31.5 12.4 4349 4396 G.DMT Annex A Infineon 230/105 ERR_HI_BER_LIMIT -13.7 -23.6 20.9 49
2013/01/03 18:01:48 PST 1 5792 5812 6064 6064 6.0 2.0 35.0 19.8 10817 0 0.00 0.25 768 804 7.0 31.5 12.4 141 59 G.DMT Annex A Infineon 230/105 ERR_HI_BER_LIMIT -14.8 -20.2 22.1 6
2013/01/03 18:41:25 PST 1 5792 5820 5724 5724 6.1 5.0 35.1 19.8 4410 0 0.00 0.25 768 768 6.0 31.5 12.4 22 0 |
|
bbear2Premium
join:2003-10-06
94045
kudos:3 | said by scottb908:the modem is hardwired to the NID and no filters installed. Seeing alot of CRC errors causing the reset.
So you are saying the wires are dedicated to your DSL modem and there is nothing else on them? The CRC errors are a symptom, not the problem. The noise margins still look suspiciously low and that alone can generate CRC errors. You need to isolate whether or not its within your premisses or from your ISP; hence my suggestion to remove everything but the modem and check your wiring and connection points.
In the DSL world things (outside your premises) do change that can affect your service. So if nothing has changed on your side, and your modem isn't flaking out, it could very well be on the outside. |
|
