dslreports logo
site
 
    All Forums Hot Topics Gallery
spc

spacer




how-to block ads


Search Topic:
uniqs
33
share rss forum feed

Roop

join:2003-11-15
Ottawa, ON

3 edits
reply to Roop

Re: exploring the alcatel lucent cellpipe 7130

boot code

Net:   voxEmac
 
Type "h" for HELP. Have fun!
 
Hit any key to stop autoboot:  1  0 
Use Partition 2 to boot
length = 4978932, crc32=1b8ae6b5
CRC32 checksum OK!
Use Partition 2 to boot
## Booting image at bf800000 ...
   Image Name:   adi_kernel_2.6
   Created:      2011-09-14   2:06:05 UTC
   Image Type:   MIPS Linux Kernel Image (gzip compressed)
   Data Size:    1189550 Bytes =  1.1 MB
   Load Address: 80010000
   Entry Point:  802af000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
 
Starting kernel ...
 
Linux version 2.6.18.2 (xxxxx@CompilerServer2.gemtek.com.tw) (gcc version 3.4.3) #1193 PREEMPT Wed Sep 14 10:05:59 CST 2011
CPU revision is: 6833c400
Determined physical RAM map:
 memory: 02000000 @ 00000000 (usable)
Initial ramdisk at: 0x80000000 (0 bytes)
Built 1 zonelists.  Total pages: 8192
Kernel command line: root=/dev/mtdblock2 rw rootfstype=jffs2 myfs_start=0xbf940000 rootfstype=cramfs root=/dev/mtdblock5 
***** INFO: saved_root_name is /dev/mtdblock2 
****************************************myfs_start is 0xbf940000 
***** INFO: saved_root_name is /dev/mtdblock5 
Primary instruction cache 16kB, linesize 32 bytes.
Primary data cache 8kB, linesize 32 bytes.
Fusiv LX4189 CACHES 
Synthesized TLB refill handler (17 instructions).
Synthesized TLB load handler fastpath (31 instructions).
Synthesized TLB store handler fastpath (31 instructions).
Synthesized TLB modify handler fastpath (25 instructions).
PID hash table entries: 256 (order: 8, 1024 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 28900k/32768k available (2256k kernel code, 3852k reserved, 423k data, 164k init, 0k highmem)
Mount-cache hash table entries: 512
Checking for 'wait' instruction...  unavailable.
checking if image is initramfs... it is
Freeing initrd memory: 0k freed
NET: Registered protocol family 16
Fusiv PCI: starting...
NET: Registered protocol family 2
IP route cache hash table entries: 256 (order: -2, 1024 bytes)
TCP established hash table entries: 1024 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 1024 bind 512)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
JFFS2 version 2.2. (C) 2001-2006 Red Hat, Inc.
Initializing Cryptographic API
io scheduler noop registered (default)
Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0xb9020000 (irq = 6) is a 16450
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
PPP generic driver version 2.4.2
NET: Registered protocol family 24
*****************************************In init_mb tmp is 0x1f940000
On Board flash device: 0x1000000 at 0x1f000000
ADI flash: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
  Silicon revision: 6
  Address sensitive unlock: Not required
  Erase Suspend: Read/write
  Block protection: 1 sectors per group
  Temporary block unprotect: Not supported
  Block protect/unprotect scheme: 8
  Number of simultaneous operations: 0
  Burst mode: Not supported
  Page mode: 8 word page
  Vpp Supply Minimum Program/Erase Voltage: 11.5 V
  Vpp Supply Maximum Program/Erase Voltage: 12.5 V
  Top/Bottom Boot Block: Uniform, Bottom WP
ADI flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 6 MTD partitions on "ADI flash":
0x00000000-0x00060000 : "ADI uBOOT Partition"
0x00060000-0x001a0000 : "ADI Flash OS Partition"
0x001a0000-0x00800000 : "ADI Flash FS Partition"
0x00800000-0x00940000 : "ADI Flash OS-2 Partition"
0x00940000-0x00f60000 : "ADI Flash FS-2 Partition"
0x00f60000-0x01000000 : "ADI Config JFFS2 Partition"
ip_conntrack version 2.4 (256 buckets, 2048 max) - 268 bytes per conntrack
ip_conntrack_rtsp v0.6.21 loading
ip_nat_rtsp v0.6.21 loading
ip_conntrack_pptp version 3.1 loaded
ip_nat_pptp version 3.0 loaded
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 164k freed
bmedrv: module license 'proprietary' taints kernel.
***** VDSL BME driver registered with Major number: 254 *****
fusiv library initializing...
 
fusiv library initialized SUCCESSFULLY... 
Timers are getting initalized
 
Timers are initilized SUCCESSFULLY...
periApDriverInit: doneSlave Mem Alloc: Req size 16   Ptr2Block 0x191f0000
 
 *******LOAD firmware to AP:PERI_ID result:0Load into PERI_AP APU Successful !!!
 
 Added AP PREROUTE Hook 
 Added AP POSTROUTE Hook 
 Buffer Manager is initializing...
Slave Mem Alloc: Req size 16   Ptr2Block 0x191f0010
Load into BM APU Successful !!!
 
** Switch driver installed successfully - v.6.9.4 5th Nov, 2008 **
Slave Mem Alloc: Req size 16   Ptr2Block 0x191f0020
Slave Mem Alloc: Req size 16   Ptr2Block 0x191f0030
 
Ethernet Driver is initialized SUCCESSFULLY
***** PPP over Ethernet Relay driver registered with Major number: 253 *****
IGMP Snoop Module inserted successfully- v6.6 on 2007.09.26
Ikanos Fusiv Watchdog  is registered as char device Major No 0
Set Switch as Power Down Mode
nvram_init: INFO=>nvram conf initialized successfully!
nvram_init: INFO=> RAM CONF successful created!
nvram_init: INFO=>nvram MAC initialized successfully!
nvram_init: INFO=>nvram TR069 initialized successfully!
nvram_init: INFO=> RC.CONF successful created!
 
ipos system initialized 
CreateTimer15Mins(): success 
IPOS:Unable to run the API.  BME is idle.
start autoRestart from UI Task
 
BME 1 is coming up
Fusiv oampBmeStart() ../
 
b1p0  iposBmeStartBlk cmdtag 0 status: IN PROGRESS 
cpe> 
INI RESETHello 2 
 
Downloading BME 1 software..... klogd started: BusyBox v1.00 (2011.07.08-04:35+0000)
killall: syslogd: no process killed
IPOS:Unable to run the API.  BME is idle.
IPOS:Unable to run the API.  BME is idle.
IPOS:Unable to run the API.  BME is idle.
cat: /etc/config/Panic_Log_10: No such file or directory
Sat Nov 26 04:10:00 UTC 2011
IPOS:Unable to run the API.  BME is idle.
IPOS:Unable to run the API.  BME is idle.
/usr/shell/lan.sh start ok
IPOS:Unable to run the API.  BME is idle.
/usr/shell/hostname.sh config ok
Use RT2880 WLAN Module!!
IPOS:Unable to run the API.  BME is idle.
RT2880 iNIC: 802.11n WLAN PCI driver v2.0.0.0 (Jan. 15, 2009)
RT2880 iNIC: pci dev 0000:00:01.0 (id 1814:0801 rev 00)
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
rt->regs = ba100000
===> Get MAC from iNIC
============= Init Thread ===================
RacfgTaskThread pid = 236
RacfgBacklogThread pid = 237
ra0: Ralink iNIC at 0xba100000, 00:43:0c:00:00:00, IRQ 25
IPOS:Unable to run the API.  BME is idle.
failed to query MAC address (stat=54)
IPOS:Unable to run the API.  BME is idle.
IPOS:Unable to run the API.  BME is idle.
IPOS:Unable to run the API.  BME is idle.
IPOS:Unable to run the API.  BME is idle.
IPOS:Unable to run the API.  BME is idle.
 
Bme 1 software code downloaded successfully
b1p0  iposBmeStartBlk cmdtag 0 status: COMPLETE 
cpe> 
 alm freq 20
 status freq 30
b1p0  iposPeriodicReportEnable cmdtag 99 status: IN PROGRESS 
cpe> 
 alm freq 20
 status freq 30
b1p0  iposPeriodicReportEnable cmdtag 99 status: IN PROGRESS 
cpe> 
b1p0  iposPeriodicReportEnable cmdtag 99 status: COMPLETE 
cpe> rm: cannot remove `/tmp/oldrc.conf.bridge': No such file or directory
device eth0 entered promiscuous mode
b0: port 1(eth0) entering learning state
Server: Unknown InterfaceFailed to set parameters for server interface
pppoe-relay can't be enbaled: No server interface is configured
/usr/shell/bridge.sh start error
/usr/shell/udhcpd.sh config_boot ok
 
***** udhcpd start ver 1000 *****
info, udhcpd (v0.9.9-pre) started
error, max_leases value (254) not sane, setting to 245 instead
server_config.max_leases_ratio : 183
error, Unable to open /etc/config/gt_old_lease for reading
gt_lease_check: -1
error, Unable to open /tmp/gt_old_lease for reading
[in background ]DebugMessage: 0 
/usr/shell/udhcpd.sh start ok
Set Switch as Normal Operation
 
Please execute 'vdsl 900' in 15 seconds to enter into Supervisor mode
_nvram_get: ERROR=> nvram_get() the wrong field[wl_enable]
Enter main
Enter getFromNV
Enter SetupMultiCast
IPAddr=192.168.2.1
MultiCastGroup=239.255.255.239
start easyconf and mac writer
link not up yet!!: No such file or directory
Ikanos watchdog: Enable Watch Dog !
 
Enable Watch Dog!!
AC:81:12:xx:xx:xx
Use RT2880 WLAN AC Module!!
module wlan_ac installed!!
[wlan_ac] wireless default interface ra0
[wlan_ac] ra0 mac addr : 00 43 0C 00 00 00 
BC::Bridge Filter 
b0 mac=AC:81:12:xx:xx:xx  
b0gwlan_client_info.alg=2
 maclistgwlan_client_info.mode=0
 isgwlan_client_info.broadcastMac=ff:ff:ff:ff:ff:ff
 empgwlan_client_info.bridgeMac=ac:81:12:xx:xx:xx
ty.gwlan_client_info.num=0
.
gwlan_client_info.eth_type=0000
Have done mass production
Group added successfully
 
Group added successfully