dslreports logo
site
 
    All Forums Hot Topics Gallery
spc

spacer




how-to block ads


Search Topic:
uniqs
39
share rss forum feed

SpHeRe31459
Premium
join:2002-10-09
Sacramento, CA
kudos:2
reply to telcodad

Re: [X1] Xfinity X1 now available to New Customers

said by telcodad:

I believe just about any RNG box from Motorola, Cisco and Pace would be able to support the X1 guide, but I can't find a specific post from him stating that.

I should clarify, we both know the hardware is capable. I meant any rollout information. So far his comments have all been focused on Cisco hardware, but that could of course simply be because it's in a Cisco thread...


cypherstream
Premium,MVM
join:2004-12-02
Reading, PA
kudos:3
Push is technically possible with DSG active. OOB command would inform the box to turn on DSG mode. DOCSIS modem in box does a hunt and acquires a 2-way communication with the CMTS. It registers with the CMTS and the docsis-tunnel configuration in the CMTS routes its traffic appropriately as its configured to know the difference between cable modems and set top boxes.

Once locked onto a 38.8mbps data channel, pushing X1 is now possible.

Look at it this way... DirecTV updated the UI to HD over the air. Andorid phones update over the air. iPhones now update over the air. Anything is possible... just have to write proper code to do so.


telcodad
Premium
join:2011-09-16
Lincroft, NJ
kudos:15
Well, while it may be "technically possible," in this post »Re: New Guides for SA/Cisco Areas (Info from Ted Hodgins Blog) from the "New Guides for SA/Cisco Areas" thread, Ted Hodgins had this explanation for why they wouldn't push OSG 2.0 out to existing, in-home boxes:
... it's fairly technical, but to keep the explanation simple, the new On-Screen Guide 2.0 is delivered to our newest cable boxes via a different and newer protocol and technology (called OCAP or tru2way).

The RNG 200 that you have in your home today is not assigned to the tru2way mode and can't be easily flipped or changed into that mode and preserve your current DVR recordings, favorites and other user configurable settings which would be a bad customer experience.

SpHeRe31459
Premium
join:2002-10-09
Sacramento, CA
kudos:2
said by telcodad:

Well, while it may be "technically possible," in this post »Re: New Guides for SA/Cisco Areas (Info from Ted Hodgins Blog) from the "New Guides for SA/Cisco Areas" thread, Ted Hodgins had this explanation for why they wouldn't push OSG 2.0 out to existing, in-home boxes:

... it's fairly technical, but to keep the explanation simple, the new On-Screen Guide 2.0 is delivered to our newest cable boxes via a different and newer protocol and technology (called OCAP or tru2way).

The RNG 200 that you have in your home today is not assigned to the tru2way mode and can't be easily flipped or changed into that mode and preserve your current DVR recordings, favorites and other user configurable settings which would be a bad customer experience.

Yep that makes sense. The guide software is completely different, it isn't just an incremental update. I assume it requires activating the Tru2Way middleware and loading the guide software with it. i-Guide is in no way Tru2way enabled of course, since fundamentally it's the same software as it was in 1999.

So it would require a complete reset of the software on the box. That would come as quite a surprise to people. (Though personally if I were warned with plenty of time, I'd be fine with it.)
I still hope they figure out how to transition though, I mean it's supposed to be their goal to move all capable hardware forward and make i-Guide their legacy guide. Most people aren't going to swap boxes "just because" - most people don't even know or care that there is a much newer/nicer UI.