Selected ISP Support > Cyberonic > Speedstream 5861 Still can't reset password. Help!

reply to ealimam

Re: Speedstream 5861 Still can't reset password. Help!

The firewall is probably not the issue. I don't believe Cyberonic puts any rules in place. Post the output of the following commands:

sys list
eth list
rem list cpe (not sure "cpe" is the name of the remote interface, could be "internet")

Make sure you x out your IP address on the remote list. Better not to advertise your public IP address in an open forum.

here is my configuration that can only ping:

# sys list
GENERAL INFORMATION FOR
System started on.................... 2/8/2003 at 2:25
Authentication override.............. none
WAN to WAN Forwarding................ yes
Block NetBIOS Default................ no
BOOTP/DHCP Server address............ none
Telnet Port.......................... default (23)
Telnet Clients....................... all
SNMP Port............................ default (161)
SNMP Clients......................... all
HTTP Port............................ default (80)
HTTP Clients......................... all
Syslog Port.......................... default (514)
Allowed Syslog Servers............... all
Default Syslog Servers............... none
System message: Configured Feb 2003
Security timer....................... 10 minutes
One WAN Dial Up...................... no
Management feature................... 0
Rip timer............................ 30
VPN Pass-thru of multiple clients.... no
Backup............................... no (no valid remote profile is enabled)
Retry Interval In Minutes.......... 30
Stability Interval In Minutes...... 3

MODEM STRINGS:
Reset: ATZ
Escape: +++
Init: ATS0=0Q0V1&C1&D0X4S12=20
Off-Hook: ATH1
Dial: ATDT
Answer: ATA
Hangup: ATH0

# rem list
INFORMATION FOR
Status............................... enabled
Interface in use..................... HSD
Protocol in use...................... RFC1483 (SNAP)
ATM traffic shaping...................no
Connection Identifier (VPI*VCI)...... 0*35
IP address translation............... on
IP filters defined................... no
Send/Receive Multicast............... off
Block NetBIOS Packets................ off
Source IP address/subnet mask........ x.x.x.x/255.255.255.252
Remote IP address/subnet mask........ 0.0.0.0/0.0.0.0
Management IP address/subnet mask.... 0.0.0.0/0.0.0.0
Send IP RIP to this dest............. no
Send IP default route if known..... no
Receive IP RIP from this dest........ no
Receive IP default route by RIP.... no
Keep this IP destination private..... yes
Total IP remote routes............... 1
0.0.0.0/0.0.0.0/1
IPX network number................... 00000000
Use IPX RIP/SAP (negotiate with PPP): yes
Total IPX remote routes.............. 0
Total IPX SAPs....................... 0
Bridging enabled..................... no
Exchange spanning tree with dest... no
Bridge only PPPoE with dest........ no
mtu.................................. 1500

# eth list
GLOBAL BRIDGING/ROUTING SETTINGS:
Bridging enabled..................... no
Exchange spanning tree with dest... yes
Bridge only PPPoE with dest........ no
IP Routing enabled................... yes
Multicast forwarding enabled....... no
Firewall filter enabled ........... yes
Directed Broadcasts Allowed........ no
RIP Multicast address.............. default
VRRP Multicast address............. default
IPX Routing enabled.................. no

ETHERNET INFORMATION FOR
Hardware MAC address................. 00:20:6F:15:B5:6B
Send IP RIP to the LAN............... no
Advertise me as default router..... yes
Process IP RIP packets received...... no
Receive default route by RIP....... yes
IP address translation............... yes
IP filters defined................... no
IP address/subnet mask............... 10.0.0.1/255.255.255.0
Management IP address/subnet mask.... 0.0.0.0/0.0.0.0
Static Ethernet routes defined....... none
Virtual Ethernet routes defined...... none
IPX External network number.......... 00000000
IPX Frame type....................... 802.2
MTU.................................. default

any idea?

Looks like you've got too much NAT going on! Only need to turn on IP address translation at the remote interface. Turn off NAT on the ethernet interface:

eth ip trans off 0:0
save
eth restart 0:0

If the restart doesn't cause the new value to take effect then use reboot. Let us know how it goes!
[text was edited by author 2003-02-08 14:52:23]

Yep. That was it! I didn't even have to reboot. I now have the INTERNET at my disposal, bwuuahahahahaha! Thanks again for all your help. Much appreciated!

Emory