This is what Sprint gave me: »
local.sprint.com/home/lo ··· 645m.pdf.... no luck on getting Dlink running.
Other way that I have not done yet due to browser wont allow me to open URL: 192.168.1.1 but able to do so in DOS: telnet 192.168.1.1.........I use D-Link for VideoPhone.
I will try this tonight but problem is how do i get Internet Browser to open 192.168.1.1 instead of DOS/CMD then telnet 192.168.1.1??????
Keith,
Instruction is very long. Let us know if you have any problems.
This guide will assist you in setting up port forwarding and Bridge for
use
with VP-100 with ease of use. Please remember if you see "?", it
represents
a command or info and do not include " when you type.
1. Open Browser (IE/Netscape) and type "192.168.1.1" into the address
bar.
Press "Enter".
2. A dialog will appears requesting a User Name and Password. Enter
"admin"
for the User Name, and enter the modem password for the Passord. The
default
password is "1234". (Hint: If a customer install the SprintDSL instead
of
SprintDSL installer, it is possible the customer set their own admin
password. Please ask the customer for a password.
3. The Web-Configurator screen will be displayed. You will need to
access
the modem's advanced features. Click the "NAT" link under "Advanced
Setup".
4. The NAT-Mode window will appear. Make sure "SUA Only" is selected.
Click
the "Edit Details" link next to "SUA Only".
5. The "NAT-Edit SUA/NAT Server Set" page will display. This is where
you
can select the port you would like to forward.
6. You can put your computer into the "DMZ" (demilitarized zone), and
it
will turn off all of the NAT security features. To place a computer in
the
DMZ, type the IP address of the computer into the "IP Address" field on
line
1 (All ports). The only IP address that can be used is "192.168.1.2".
(Hint:
This IP address is assigned by SprintDSL which allow customer to have
only 1
IP address. Therefore, it has a built-in router and only allow 1
computer to
access to the internet.)
7. Remember, if the customer does not play game on the internet,
proceed
with instruction on Number 6 & 8. If the customer plays game on the
internet, You can specify one port, or a range of ports, to forward
traffic
from. To forward one port, type the port number into the "Start Port
Number"
field and also into the "End Port Number" field. Type the port number
recommend by SorensonVRS for Inbound Ports/Outbound Ports. Remember,
The
only IP address that can be used is "192.168.1.2"
8. Click "Save"
9. The NAT Mode will appear. Click "Apply". The Port forwarding works
for
TCP ports, not UDP ports. If you are trying to forward UDP ports, the
modem
will need to be configured as a Bridge, and a DLINK 604 Router or other
means of router brand will need to be established. Please proceed to
Number
10 to convert a Zyxel 645M Series to Bridged Mode. (Hint: Once the modem
is
configured as a Bridge, it will no longer perform the PPPoE connection
and
an alternative method for PPPoE authentiction must be used which will
be
describes at the end of the instuction note.)
10. Click on the "Start" button and select "Run". Type the following
command: "telnet 192.168.1.1" Then, click on "OK". (Hint: Macintosh
users
will need to use a telnet client to telnet to the same address.)
11. You will be prompted to enter a password, the default for the
Zyxel
645M is: "1234" or "Customer's password". After typing the password
press
"Enter".
12. The Main Menu for the Zyxel 645M should appear. First you will need
to
access menu 1. Type "1" followed by the "Enter" key.
13. The General Setup screen will be displayed, the default
configuration
of the device (Route/NAT mode) has Route IP set to Yes, and Bridge set
to
No.
These settings will need to be reversed in order for the modem to
function
as a Bridge. Press the "Enter" key until the cursor is next to Route
IP.
Then, press "Space Bar" to toggle the setting to "No". Press "Enter"
until
the cursor is next to Bridge and toggle the setting to "Yes".
14. Press "Enter" until the settings are saved to ROM and you are
returned
to the main menu.
15. Access menu 4 from the main menu to display Internet Access Setup
screen.
The default Encapsulation will need to be changed to "RFC 1483" (using
"Space Bar" and "Enter" keys as in step 13).
Single User Account will also need to be changed to "No".
Press "Enter" until changes are saved to ROM. (Hint: Firmware)
16. Access menu 11 from the main menu to see the Remote Node Setup
screen.
Enter node number 1 and press "Enter" to proceed.
17. In the Remote Node Profile, verify that Active is set to "Yes". It
will
probably be necessary to toggle "Route" to "None". As well as "Bridge"
to
"Yes". (Using the "Space Bar" and "Enter" keys as in step 13.)
Press "Enter" until the message "Saving to ROM" appears and you are
returned
to menu 11.
18. You will be returned to menu 11. Press "ESC" to return to the main
menu.
19. From the main menu type "99" and press "Enter" to exit the session
and
you're done with the setup of the Bridge. (Hint: You are now required
to
setup a PPPoE authentication which will be described next.)
20. Click on "Control Panel"
21. Click on "Network and Internet Connections"
22. Click on "Network Connections"
23. Click "Create a New Connection" and a "Welcome to New Connection
Wizard" prompt screen will come up, Click "Next", then select "Connect
to
the Internet", then Click "Next", then Select "Setup my Conneciton
Manually", then Click "Next", then Select "Connect using a broadband
connection that require a username and password", then Click "Next",
then
Type "SprintDSL" (Hint: This is for the name of your ISP), then Click
"Next".
24. Type in "Username and Passord" (Username: email address &
Password:
customer's password) and unselect "Turn on Internet Connection Firewall
for
this connection" (Hint: It is a must.) then Click "Next", and Select
"Add a
shortcut to this connection to my desktop".
25. Click "Finish"
26. The router is now disable in the modem and it is now officially a
Bridge modem.
27. Turn off your computer, turn off the DSL Modem, and then add DLink
Router. Turn on DLink Router & wait for 5 seconds then turn on the DSL
Modem.
28. Wait for a few minutes utnil you see "DSL" light goes on solid.
Turn on
the computer.
29. Open IE/Netscape browser and type "http://192.168.0.1".
30. Type "admin" for username and blank for password.
31. Click "Home"
32. Click "WAN"
33. Select "PPPoE"
34. Select either "Dynamic PPPoE" or "Static PPPoE". (Hint: If
customer
don't have Static IP, select Dynamic PPPoE.)
35. Type in the username with full email address
36. Click "Apply"
37. Select "Advanced"
38. Select "DMZ"
39. Select "Enabled" and type "125" (192.168.0.125)
40. Click "Apply" and Viola! (Hint: You will see a SprintDSL shortcut
icon
on the customer's screen. Tell customer not to worry and this is for
the
purpose of technical support.
Sincerely,
