Re: [Wired] BEFSR41 Version??

Forums » Equipment Support » Hardware By Brand » Linksys » [Wired] BEFSR41 Version??


Share Topic:	RSS topic:	toggle: flat / full normal / watch	Posting:	Post a:	Post a:

Links: ·Forum Rules ·Forum FAQ ·FTP Modes & Ports ·Linksys Home

Linksys WRT54G -with Alchemy settings »
« DD-WRT released firmware for WRT54G+GS is out! :)

jbob
Reach Out and Touch Someone
Premium
join:2004-04-26
Little Rock, AR

·Comcast

·AT&T Southwest

1 edit

Re: [Wired] BEFSR41 Version??

There was a hardware change between v1 and v2 for some bug I think. My BEFSR41 clearly shows ver. 2 by model no on the bottom. I had a V1 but got toasted by a lightening strike. They also changed the power supplies. I can't find my v1 now but I think it had a two pin connector in the back while my v2 has the standard single pin hole. If I'm not mistaken the power adapter was inline for v1 while the v2 is a brick. The V1 and V2 use the same firmware.
I do not have a v3 but it uses different firmware as does the v4 now as well.

To access the router you do need to use 192.168.1.1 unless it has been changed from the default. If you are not sure of what it is then press the reset button in for 30 seconds(long reset) to accomplish a hard reset of the router. You should then be able to access it using 192.168.1.1 with the password (admin).

I am not sure now but did the earlier SR41's include an option to upgrade the firmware via the web interface? If not you will need to use the TFTP program found on the Linksys web site.

permalink · 2005-07-22 16:48:56 · Print ·

Comp Cmndo

join:2003-08-12
FL-USA

Re: [Wired] BEFSR41 Version??

said by jbob

:

There was a hardware change between v1 and v2 for some bug I think. My BEFSR41 clearly shows ver. 2 by model no on the bottom. I had a V1 but got toasted by a lightening strike. They also changed the power supplies. I can't find my v1 now but I think it had a two pin connector in the back while my v2 has the standard single pin hole. If I'm not mistaken the power adapter was inline for v1 while the v2 is a brick. The V1 and V2 use the same firmware.
I do not have a v3 but it uses different firmware as does the v4 now as well.

To access the router you do need to use 192.168.1.1 unless it has been changed from the default. If you are not sure of what it is then press the reset button in for 30 seconds(long reset) to accomplish a hard reset of the router. You should then be able to access it using 192.168.1.1 with the password (admin).

I am not sure now but did the earlier SR41's include an option to upgrade the firmware via the web interface? If not you will need to use the TFTP program found on the Linksys web site.

Exactly!! Correct on all counts. The hardware change between the V1 & V2 is the internal power supply.

I've had a V1, V2, and V3.1
V2 - bought this 1st, it died mysteriously, was replaced. Internal power supply was okay. Standard 9VAC @ 1A power "brick".
V1 - found it in the trash, fixed blown power supply (internal fuse was blown). One port is dead. Power supply has a vented case and is a proprietary power supply, 5VDC @ 3A. Operates the same as the V2, except this one is not dead.
V3.1 - still in box, same power brick as V2. Just 6 LEDs, 1-power. 4-ports, 1-Internet. There is no diagnosic LED.

Also, V1 & V2 WAN is 10mbps, V3 WAN is 100mbps.

BTW, I always use the TFTP and never the web update.

permalink · 2005-07-23 15:47:49 · Print ·

your comment..

Forums » Equipment Support » Hardware By Brand » Linksys	Linksys WRT54G -with Alchemy settings » « DD-WRT released firmware for WRT54G+GS is out! :)


Monday, 14-Dec 16:09:36	Terms of Use \| Privacy Policy \| Hosting by www.nac.net - DSL,Hosting & Co-lo \| feedback \| contact over 10 years online! © 1999-2009 dslreports.com. page compression OFF