mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| reply to kukku
Re: [PAP2] Unlocking Guide
said by kukku  :but how do i get to the web interface whats the ip address where or how do i get the ip address of the adapter This question has been asked so many times with answers!
--
Mazi (UK Non-Geo Phone: +44-703-194-2574) |
|
christcorp
Premium
join:2001-05-21
Cheyenne, WY
 ·Bresnan Online
 ·VOIPo
| reply to kukku
Not sure if I understand your question, but the IP address of the adapter is whatever your router gave it through dhcp. By default, the PAP2 will get it's IP address dynamically. You need to look at the dhcp list in your router and it will tell you which IP addresses are being used. It will be one of those listed. Unless I am misunderstanding the question??? later... Mike... |
|
kukku
join:2006-05-31
Abbotsford, BC | reply to mazilo
but how do i get to the web interface whats the ip address where or how do i get the ip address of the adapter |
|
exousia1
join:2005-10-09
Anaheim, CA
| reply to mazilo
I want to get my PAP2 back to Linksys PAP-2 firmware. I tried to unlock it. Right now the admin page shows Sipura. Will a factory reset do this or do I need to reload the firmware? Where can I get that firmware? How do I actually do a factory reset? Any help you can give me will be greatly appreciated. Thank you! |
|
RonR
join:2003-10-10
Downey, CA
| reply to voipsw
said by voipsw :I want to know how to do factory reset too. Factory Reset:
****
73738#
(73738 = 'RESET' on keypad) |
|
voipsw
join:2005-09-30
Live Oak, FL | reply to JTS33
I want to know how to do factory reset too. |
|
JTS33
join:2003-05-03
USA
| reply to mazilo
said by mazilo :Once unlocked, please be sure not to perform any factory reset which will eventually relock the device. How do you perform a factory reset on the PAP2? |
|
hardly
join:2004-02-10
USA
| reply to rizzo2dial
Is there a modified Sipura firmware available that will load using the PAP2 web interface from a file located on a local machine?
Would that effectively turn this device into a SPA2000 (or SPA2002), then only needing to update firmware as if it were a Sipura and not dealing with it reverting to a locked Vonage device?
PM me if you need to.
Thanks
said by rizzo2dial :The PAP2 and PAP2-NA use identical firmware. The PAP2 has different NVRAM values burned into the device than the PAP2-NA which is why a Master Reset reverts the device back to a locked Vonage adapter. I tried numerous combinations of trying to reset the adapter (both while in "Sipura" mode and "Linksys" mode, switching back 'n forth between the firmware flavors). It "Sipura" mode, a master reset acted like all "default Sipura" settings were loaded; however, once switching back to "Linksys" firmware, it was a locked PAP2 Vonage adapter again. Rizzo |
|
mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| reply to hardly
said by hardly :Once unlocked, can you flash with Linksys PAP-2NA firmware? PAP2 and PAP2-NA firmware are 100% identical.
If so, can you then perform a Factory Reset without worrying about it reverting to Vonage defaults?
Thanks Once unlocked and factory reset, the PAP2 will be locked again. |
|
rizzo2dial
Premium
join:2004-08-05
| reply to hardly
The PAP2 and PAP2-NA use identical firmware. The PAP2 has different NVRAM values burned into the device than the PAP2-NA which is why a Master Reset reverts the device back to a locked Vonage adapter.
I tried numerous combinations of trying to reset the adapter (both while in "Sipura" mode and "Linksys" mode, switching back 'n forth between the firmware flavors).
It "Sipura" mode, a master reset acted like all "default Sipura" settings were loaded; however, once switching back to "Linksys" firmware, it was a locked PAP2 Vonage adapter again.
Rizzo |
|
hardly
join:2004-02-10
USA | reply to mazilo
Once unlocked, can you flash with Linksys PAP-2NA firmware?
If so, can you then perform a Factory Reset without worrying about it reverting to Vonage defaults?
Thanks |
|
mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA | reply to rcilink
Once unlocked, please be sure not to perform any factory reset which will eventually relock the device. |
|
