how-to block ads
|
|
Share Topic
 |
 |
|
|
|
| reply to grohgreg
Re: Minimum cable length said by grohgreg :
Then add your 62dB "transmitter gain", then add the known antenna G/T of 15.4
I'm sorry, it looks like it's my turn to call this gibberish.
First off, G/T is a measure of receive performance, you can't add it to the transmit side like you're trying to do.
Second, the 3 watt spec (sorry, I had the 4 watts wrong) is for the output of the transmitter, and has nothing to do with the antenna it's connected to. The Transciever spec (referenced earlier) says that the typical maximum output power (P1dB) is 34.8 dBm, or 4.8 dBW, or 3 watts. So your examples become:
-35 dBm - 6.3 + 62 = 20.7 dBm, or about a 10th of a watt.
-5 dBm - 6.3 + 62 = 50.7 dBm, which is limited to 34.8 dBm by the transmitter capabilities.
Now, if you want to talk about EIRP, figure the transmit gain is about 45 dBi. (Again, I haven't seen the specs for WB's particualr dish, 45 is a spec for a Patriot Ka band dish of similar size.) This is added to the above results, and do give what seem rediculously large numbers. But, EIRP is how much power you would need if you had an isotropic antenna (non-directional), not a dish.
Does the 62 dB figure make more sense now? (Actually 48 to 63, as it turns out I was picing the high end.) | |
| said by joebob42 :
figure the transmit gain is about 45 dBi.
To correct myself, this should be 39.5 dBi for the WB dish. | |
 grohgregDunno. Ask The Chief
join:2001-07-05
Dawson Springs, KY
2 edits | reply to joebob42
said by joebob42 :
First off, G/T is a measure of receive performance, you can't add it to the transmit side like you're trying to do. Granted, earth terminal G/T is the figure of merit at the receiver antenna. The standard formula is "G/T = Receive Antenna gain – 10 log(system noise temperature). Bear with me here, cuz I can't edit subscript into the next few sentences. But consider that since this same antenna transmits as well, the Gt (gain-transmit) is also related to G/T. And since gain is a function of frequency, Gt is always better than Gr (on the same antenna). I will concede though, that using 15.4 to represent antenna gain in the previous example was redundant. Rather than grab the convenient G/T value, I should have crunched the numbers.
But no, a transmitter gain of 62dB didn't compute initially, until you qualified it as dBm. 62 dBm equates to 32 dBW. I originally interpreted your post as meaning 62 dBW. Big difference. Anyway, we agree that
-35 dBm - 6.3 + 62 = 20.7 dBm, and
-5 dBm - 6.3 + 62 = 50.7 dBm.
But to arrive at EIRP, you must add Gt. Using your numbers:
-35 dBm - 6.3 + 62 = 20.7 + 39.5 = EIRP 60.2 dBm (30.2 dBW)
-5 dBm - 6.3 + 62 = 50.7 + 39.5 = EIRP 90.2 dBm (60.2 dBwW)
ViaSat data rates the 62cm configuration at EIRP 48 to 58 dBW. So now we're pretty close at the top end. I'm sure the tenths will be variable relative to cable loss. Not sure what's going on at the bottom though (30.2).
Backing up a bit, we tentatively agree that -5 dBm - 6.3 + 62 = 50.7. And I'm guessing you just picked 34.8 dBm because it conveniently equates to 3 watts. What I'm still missing is how the 50.7 becomes "limited to 34.8 dBm by the transmitter capabilities".
//greg//
--
DW4000CE/1.2 Ghz Tualatin/512 PC133 - W2K Pro/SP4 - SRS G11/1370H - RSL83/ACP81 - v4.2.1.10C - RWIN 513920/MTU 1500 - proxy switch - Gateway/DNS 205.177.62.91/66.82.4.8 plus rollovers - Firefox 1.02 | |
| said by grohgreg :
But no, a transmitter gain of 62dB didn't compute initially, until you qualified it as dBm.
I still don't think we're quite on the same page, but the end result may still be the same.
I never said the transmitter gain was 62 dBm. dBm only makes sense in terms of transmit power.
said by ghrogreg :
And I'm guessing you just picked 34.8 dBm because it conveniently equates to 3 watts.
No, I picked 34.8 dBm direct from the U.S.Monolithics datasheet (»www.usmonolithics.com/products/c···1024.pdf), as the Output Power at the 1dB compression point. From the same datasheet:
Small Signal Transmit Gain (over freq. and temp.):
Min: 48 dB
Typical: 56 dB
Max: 63 dB
Note the units: power as dBm, gain as dB. As it turns out, when I guessed 62 dB for the gain, I was high, but still within the spec.
For more on how RF amplifiers are rated, and the meaning of P1dB, take a look at »www.evaluationengineering.com/ar···iers.htm .
Disclaimer... I hadn't seen the spec sheets when we started this discussion... but now we have more information... | |
| reply to grohgreg
said by ghrogreg :
Rather than grab the convenient G/T value, I should have crunched the numbers.
Thanks for clarifying that.
It looks like the antenna datasheet is at »raven.co.uk/satellite-products/d···heet.pdf
Though they show Gt at 14.25 GHz, rather than at 30 GHz, so I'm not sure... | |
|
