dslreports logo
 
    All Forums Hot Topics Gallery
spc
uniqs
46
michaelr7
join:2004-03-26
Tucson, AZ

1 edit

michaelr7 to mgw246

Member

to mgw246

Re: Anyone successfully using a Cisco 877 with Qwest?

I have an 877 at a couple of sites using Qwest DSL and Qwest.net as the ISP. This is what I use:

interface ATM0
no ip address
no ip mroute-cache
atm vc-per-vp 64
no atm ilmi-keepalive
!
pvc 0/32
encapsulation aal5mux ppp dialer
dialer pool-member 1
dsl operating-mode auto
!
interface Dialer1
description outside interface
ip address negotiated
ip access-group fw_acl in
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat outside
ip ips fw_ips in
ip virtual-reassembly
encapsulation ppp
dialer pool 1
dialer-group 1
no cdp enable
ppp authentication chap pap callin
ppp chap hostname xxxx
ppp chap password 7 nnnn
ppp pap sent-username xxxx password 7 nnnn
ppp ipcp dns request
ppp ipcp address accept
!
dialer-list 1 protocol ip permit

I also have a crypto map and service policy on the dialer1 interface but that isn't Qwest specific.

The very first time I setup a router with Qwest I configured both PAP and CHAP since I wasn't sure which one Qwest.net uses. I've left it that way since it doesn't hurt anything.
Turns out Cisco is very consistent. The above config is used on my 827, 837, 877 and the WIC on my 1841 and 2811.
mgw246
join:2004-01-03
Moscow, ID

mgw246

Member

Cool, thanks!

I have MSN as my isp right now..
philipp86
join:2004-09-08
Boise, ID

philipp86 to michaelr7

Member

to michaelr7
What sort of performance are you seeing?

What does "show dsl int atm0" (or whatever) tell you?

Thanks,

-Philip
mr_dirt
join:2006-02-14
Denver, CO

mr_dirt

Member

said by philipp86:

What sort of performance are you seeing?

What does "show dsl int atm0" (or whatever) tell you?
All of my ATM configuration is pretty much at the default. I didn't adjust any of my layer 2 stuff, so I may actually be getting less than my ideal thruput. Of course, I'm pleased as hell that I can get DSL out here in the sticks. Best I could do 3 years ago was 24 Kbps.

Here ya go:

ATM0
Alcatel 20190 chipset information
ATU-R (DS) ATU-C (US)
Modem Status: Showtime (DMTDSL_SHOWTIME)
DSL Mode: ITU G.992.1 (G.DMT) Annex A
ITU STD NUM: 0x03 0x1
Vendor ID: 'STMI' 'CTNW'
Vendor Specific: 0x0000 0x0000
Vendor Country: 0x0F 0xD1
Capacity Used: 21% 98%
Noise Margin: 7.0 dB 6.0 dB
Output Power: 8.0 dBm 9.5 dBm
Attenuation: 37.0 dB 10.0 dB
Defect Status: None None
Last Fail Code: None
Watchdog Counter: 0x33
Watchdog Resets: 0
Selftest Result: 0x00
Subfunction: 0x00
Interrupts: 3849 (0 spurious)
PHY Access Err: 0
Activations: 3
LED Status: ON
LED On Time: 100
LED Off Time: 100
Init FW: embedded
Operation FW: embedded
FW Version: 2.5.42

Interleave Fast Interleave Fast
Speed (kbps): 1536 0 800 0
Cells: 22823189 0 485831210 0
Reed-Solomon EC: 69 0 759 0
CRC Errors: 13 0 492 0
Header Errors: 9 0 445 4
Total BER: 6648E-12 0E-0Leakage Avarage BER:
6381E-22 0E-0
LOM Monitoring : Disabled