rmanaka
Premium
join:2006-08-07
Jenkintown, PA
| Re: [Vonage] SIP credentials, RTP300, GPP_K? Thanks, I appreciate your help!
So far it will only get to the point of registering, generating dial tone, busy, etc. but the registration will fail. It might be particular to VSPs such as Voicepulse that use a letter in their username and the Vonage WRTP54G's peculiarity.
I'm hoping that the Linksys release 3.1.17-NA firmware (now available on the Linksys website) will solve this issue, but so far I'm getting a BAD CRC error when trying to update. I don't have a CRC routine here to recalculate the CRC after patching the CYWM->CYWL product ID in the image!
So...until someone can calculate a valid CRC for this patched image, I think I'm stuck at the moment. | |
|
 
tkprojects
join:2003-06-12
Schenectady, NY
| Re: [Vonage] SIP credentials, RTP300, GPP_K? said by rmanaka  :It might be particular to VSPs such as Voicepulse that use a letter in their username and the Vonage WRTP54G's peculiarity. The RTP300 I spoke about is being used with an account that uses alphabetical characters. Though, it does not have any numeric characters. I'm not sure that that would be a problem. | |
|
rcilink
Premium
join:2003-12-15
Manchester, NH
| Getting a WRTp54G to take 3.1.17-NA... If you have tried to load up the WRTp54G with version 3.1.17-NA firmware from Linksys support and it does not take (says wrong code pattern), have a look at this:
For this project, you will need:
- a copy of wrtp54g_fw_3.1.17_US.img (get it from www.linksys.com)
- a good HEX editor
- a Linksys WRTp54G device (no, this does NOT work on a WRT54Gp2!)
- the ability to access /update.html (you must know the password)
Here's what to do:
Open the wrtp54g_fw_3.1.17_US.img file using your favorite HEX editor.
1. Change HEX offset 23 from 4D to 4C.
2. Change the last four bytes to: AB 3A 49 5D
3. Save your new file.
4. Update the firmware on your WRTp54G (/update.html) to the new firmware.
Very Important!!! Let the firmware upgrade complete!!! Do not close the web browser session! Eventually (1-2 minutes) it will load the login screen of your WRTp54G device.
If you interrupt this, you may brick your device!
One last note, you may need to do a factory reset to rid yourself of any left-over params from the former use.. I did not have to do that, so the admin password was retained, along with the router settings. The voice section lost all of the settings, as it loads a different SIP engine (resembles the Linksys PAP2).
The new Admin password is blank (nothing in the password field). This is only needed for the /update.html page on firmware 3.1.17-NA.
Good luck!! | |
|
 | KillaB7
join:2006-05-23
Vancouver, BC | Re: Getting a WRTp54G to take 3.1.17-NA... Thanks rcilink as always!
Would you be able to post an MD5 for the modded file so people don't screw this one up (myself included).
I'm assuming this one acts like a Sipura/PAP2 vs. 1.00.62-NA? | |
|
| | rcilink
Premium
join:2003-12-15
Manchester, NH
| Re: Getting a WRTp54G to take 3.1.17-NA... Sure, the MD5 for the firmware (after the above mods are done) should be: 611eb9063d2c9c8ff2e34826c1a376e2
It does have a PAP2 SIP module, unlike the 1.00.62 versions.
I was pleased to see it is more stable than the 3.1.3 and older versions we played with in the past... | |
|
| rmanaka
Premium
join:2006-08-07
Jenkintown, PA
2 edits | This is really, really great. Thank you rcilink!!! Version 3.1.17 is indeed running like a SPA-2002/PAP2 as I just reinitialized the router and then added a "Voicepulse" recommended dial plan for the SPA-2002:
(x#|xx#|*821[2-9]xx[2-9]xxxxxx|*82011x.|*xx|*1xx|[3469]11|0|00|1[2-9]xx[2-9]xxxxxx|011x.|[2-9]xx[2-9]xxxxxx)
I think the Vonage WRTP54G is really open now! :D | |
|
| | netmitra
join:2006-09-28
Sunnyvale, CA | Re: Getting a WRTp54G to take 3.1.17-NA... [ Still locked } Rmaneka;
Unfortunately my WRTP54G is still locked by Vonage and running 1.00.20. I can't unlock it so no access to update.html
Please help | |
|
| | | netmitra
join:2006-09-28
Sunnyvale, CA
| WRTP54G Unlocked ---- Thank you guys !! After 1 week of attempts - Success now.
I was successfully able to unlock my Vonage WRTP54G using the firmware upgrade procedure. The cyt software failed to do so. I used the following link and it worked like charm !
I was getting "Invalid Code Pattern" error with 3.1.17-NA firmware from Linksys support. Then I used celiom.googlepages.com/linksys code which got me onto 3.1.17, but No NA.
My router wasn't accepting any user:tivonpw password and I was stuck. Then I did a factory reset using the poke-in button at the back. After that I was able to access update.html and then upgraded the firmware. Now I am on 3.1.17 and life feels good. Configuring VIatalk was a cakewalk.
Next Project is to install astersik on this. ANy easy-2-go guide will be appreciated. | |
|
| ii904
join:2005-11-05
Brooklyn, NY | hi rcilink, would you upload your modded file ?because I don't know how to do it.Thanks in advance!! | |
|
| celiomartins
join:2006-08-19
01333001
| rcilink and other that can Help.
I've tried your instructions and the HEX offset 23 is not 4C... I am using WinHEX... anyway the MD5 was different, so I guess that's the reason whay it is not working? could you please upload it? thank you very much! | |
|
| | KillaB7
join:2006-05-23
Vancouver, BC | Re: Getting a WRTp54G to take 3.1.17-NA... 23 Decimal = 17 HEX
So when using a HEX editor, you'll be editing the byte in address 17h | |
|
| |
| | 
meister_sd
Premium
join:2006-01-29
La Mesa, CA
| Re: Getting a WRTp54G to take 3.1.17-NA... said by celiomartins :To help I did a very easy walkthrough. Wow, that page looks very nice! Did you create it or is it a template? | |
|
| | 
santunes
@net.br
| Hi,
the image file from celiomartins (wrtp54g_fw_3.1.17_USmod.img) only has 2.746.234 bytes and the image (wrtp54g_fw_3.1.17_US.img) from linksys has 3.866.632 bytes, why they are not equal in size if only 5 bytes (offset 23 + checksum) were changed ? | |
|
| |
santunes
@net.br | Hi,
I found the problem with img size, it was my download manager.
| |
|
| | |
macpas
@tpnet.pl
| Re: Getting a WRTp54G to take 3.1.17-NA... hi!
i'm using WRTP54G for Vonage
i've tried to upgrade celiomartins' img file and got message:
unexpected end of file
at the end of upgrade/upload of firmware
any idea what's wrong?
i would try upload with original linksys img file modified by myself but it's not available at linksys page anymore | |
|
| | | |
macpas
@tpnet.pl | Re: Getting a WRTp54G to take 3.1.17-NA... part 2
celiomartins' file didn't work but i've tried the one from »blog.adonias.cl/leer.php?id=81 metodo 2a and this one worked
thakns a lot 4 all participants
maciek | |
|
| | | | | rcilink
Premium
join:2003-12-15
Manchester, NH
1 edit | Re: Getting a WRTp54G to take 3.1.17-NA... said by macpas :part 2 celiomartins' file didn't work but i've tried the one from » blog.adonias.cl/leer.php?id=81 metodo 2a and this one worked thakns a lot 4 all participants maciek Thanks for that blog link.. on there one can find WRTP54G 3.1.19 firmware. I have not loaded it yet, but maybe it fixes the line1 / line2 usage issue...
EDIT: I guess I should check the linksys site more! On the site, under SUPPORT/downloads, select WRTP54G for Vonage. You can download 3.1.20 firmware!
Here is a link to a WRTP54G 3.1.20 Linksys page. From there, you can download the firmware:
»www.linksys.com/servlet/Satellit···rWrapper | |
|
| | | | | | radom11
join:2006-08-11
West Sayville, NY
| Re: Getting a WRTp54G to take 3.1.17-NA... Rclink, 
Please forgive but I am new to all of this and it looks like you are the most knowledgeable individual that helps many
We have 3 units of the WRTP which we are trying to get working for a charity group to who now need to change from "V" (no more money) and use a free Asterisk 2.7 pbx switch that we have built for them and works well in local lan location.
Spent hours reading the messages I then downloaded the wrtp54g_fw_3.1.17_US.img from celiomartins web site and got the image to load into the wrtp54g using the “stock” user/tivonpw unit, All of that was GOOD info and the unit now shows 3.1.17, I did a 60 second reload and router is working and voice section now shows SIP and other setting headers and most fields are blank.
When I downloaded the wrtp54g_fw_3.1.17_US.img from celiomartins web site it was my impression from reading the messages that the hex code changes where done to that image , Yes/No?
Anyway the box is running 3.1.17 but the user/tivonpw password no longer works in trying to do a factory reset or and when I attempt to reload any image , am I hosed?
Any material that we can read that will explain the settings in the wrtp as the booklet that was in the box only talks about “V” system and we need to talk to Asterisk or SIP.
We have wrt1.00.62-NAr6,wrtp54g-3.1.20,image availabel Please help!
Any information is much appreciated, any one knows of a easy step “guide” as this will help many
Many Thanks
Radom11  | |
|
| | | | | | | rcilink
Premium
join:2003-12-15
Manchester, NH
| Re: Getting a WRTp54G to take 3.1.17-NA... loading the 3.1.17 (-NA) version on an old vonage box is an excellent choice, as it will remain unlocked..
when you click the "voice" tab, you should now be taken to a new voice section, with menus that look/feel identical to the Linksys PAP2 unit.
Look to the right of the web page, near top and find admin login and click that. Now you can configure Line 1 to your asterisk box and the other line if needed.
I do not suggest changing firmware again, as it is not needed.
Using 3.1.17, the new "Admin" account password is blank (just put username Admin with no password).
If you need help configuring SIP to your asterisk, look for help on Linksys pap2 and asterisk. | |
|
| | | | | | | | radom11
join:2006-08-11
West Sayville, NY
| Re: Getting a WRTp54G to take 3.1.17-NA... Rcilink,
Thank you for the fast reply.
The unit is displaying only version 3.1.17 it is not indicating NA should it be indicating NA?
I did not do the Hex changes as messages from celiomartins indicated that he did the changes and then put out the image, is that correct?
I located the Ast recipe page that talks about connecting the Linksys PAP2 I will attempt to do so when we have no more users on the pbx later this evening as they are using the Asterisk and I do not want to blow anything, in your reply you indicated that the code was like and feel of a PAP2 will it program the same way?
We will use line one for asterisk pbx to provide the remote animal shelters with home office pbx functionality to the small key systems that they no have in place at the remote locations, can you suggest a free voip incoming service that we can program into line 2 and a config for it?
What is the story with the 3.1.20 that I see is now out?
Your courtesy and help is greatly appreciated.
Many Thanks.
Radom11 | |
|
| | | | | | | | |
GOUKGO
@fewpb.net | Re: Getting a WRTp54G to take 3.1.17-NA... radom11, try this one...www.sipnumber.com
Don't know anything about them but they offer what your looking for, I think.
I've been lurking and have my box up and at about the same place you are...good luck. | |
|
| | adamsge
join:2007-02-03
Pennsauken, NJ | I used the Link here to the moded img and all went fine my wrtp54g is now running on 3.1.17-NA Thanks Also will it now be able to take firmware updates now from Linksys or will the files still need to be moded. Thanks again Jerry | |
|
|
renatoz
@net.br
| Folks, I really loved this topic, but i just have 2 concerns before go on it:
1) I had downloaded the img file from the site provided by celiomartins but the MD5 of that file does not match with the one provided before from rcilink as follows:
celiomartins's MD5: 611eb9063d2c9c8ff2e34826c1a376e2
rcilink's MD5 (provided above): e3470bc9b640d73d3330cafcc62d2bc9
Does someone already tried with the celio's file?
2) I couldn't find the wrtp54g_fw_3.1.17_US.img file to download from the linksys support site ... at the WRTP54G page there was no firmware to download, but I found the WRTP54G-NA_fw_3.1.17_US.zip at the WRTP54G-NA page ... will it works with the NA image? If no, from where can I get the original file?
tkx in advance for any help on this | |
|
| | mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| Re: Getting a WRTp54G to take 3.1.17-NA... said by renatoz :
celiomartins's MD5: 611eb9063d2c9c8ff2e34826c1a376e2
rcilink's MD5 (provided above): e3470bc9b640d73d3330cafcc62d2bc9
Does someone already tried with the celio's file? Please compare what you wrote here with rcilink's original post here.
--
Mazi (UK Non-Geo Phone: +44-703-194-2574) | |
|
| retro2783
join:2006-08-24
Hillsboro, OR | Can this also be applied to the RTP300-NA_fw_3.1.17_US firmware from the Linksys site? I have the RTP300 with the 1.0.0.62-NA firmware installed. Used the CYT-Unlocker to get the logon/password.
retro2783 | |
|
| | sgonzalez
join:2006-09-08
00057 | Re: Getting a WRTp54G to take 3.1.17-NA... Can this be applid to the RTP300 router? | |
|
| |
|
Bruno
@net.br | How do you upgrade the firmware on WRTP54G? There is not such an option under the Administration menu. HELP! | |
|
| | niel8
join:2006-06-29
Baltimore, MD | Re: Getting a WRTp54G to take 3.1.17-NA... type 192.168.15.1/update.html | |
|
|
blupupher
@mindspring.com | OK, searched a little, but could not find an answer.
I know doing this will erase all my vonage setting, but is there a way to get them back so I can continue to use vonage but have full contorl of my router? | |
|
| neoalex4
join:2006-06-01
Astoria, NY | Is it possible to backup the voice settings as you would the rest of the router settings?
If yes how?
By the way, thanks for this post, works beautifully with my asterisk. | |
|
| | trade
join:2002-09-25
Fullerton, CA | Re: Getting a WRTp54G to take 3.1.17-NA... Is it possible to backup the voice settings as you would the rest of the router settings?
If yes how?
Somebody can explain me if the 3.1.17 version can works with Vonage.
TRADE | |
|
| niel8
join:2006-06-29
Baltimore, MD
| hey rcilink, well i tried to edit file using hex editor, but i couldnt understand "Change HEX offset 23 from 4D to 4C." its like first binary file and hex editor i am trying my hand on, can you please have a look at the file i attatched and fix that for me? i did last four though. | |
|
| | rcilink
Premium
join:2003-12-15
Manchester, NH
| Re: Getting a WRTp54G to take 3.1.17-NA... said by niel8 :...but i couldnt understand "Change HEX offset 23 from 4D to 4C." ... Using your hex editor, count 23 bytes from the first byte of the file.
When you get to the 23rd byte position, you should see 4D.
Change it to 4C.
Hope that helps.. | |
|
| | | niel8
join:2006-06-29
Baltimore, MD
1 edit | Re: Getting a WRTp54G to take 3.1.17-NA... well everything just went right, unit is unlocked and up and running for stanaphone, well a question though, y is it still at 192.168.15.1 with admin user name pass user/tivonpw? i thought i will b at 192.168.0.1 with admin username and pass Admin/- , NO complaints tho, thanks a lot for all this help, also the firmware reads 3.1.17 not 3.1.17-NA, is there any other firmware you have modded the WRTP54G-NA_fw_3.1.17_US available on linksys website? | |
|
| | | niel8
join:2006-06-29
Baltimore, MD
1 edit | the port forward for APPLICATIONS AND GAMING is not working, i flashed unit with the locked one and then the 3.1.17_modded one again, still having the same problem, it anyone else has the problem? is that the firmware?
i need it for playing Age of Empires online, any one familiar with loopback? i think it allows to recognise the public ip, can someone explain how to do that? | |
|
|
Skydive
@elkon.ca
| Rcilink,
Thanks for the greate help. Do you recommend 3.1.17 firmware or the 10.00.62?
What is the right digit map for a WRTP54G? is it the following: *xxT|*1xx|[349]11|1xxx[2-9]xxxxxx|[2-9]xxxxxxT|[2-9]xxxxxxxxx|011x.T
Appreciate your help!
Wiss
skydive36@hotmail.com | |
|
| |
See 11 replies to this post |
|
| carmatt59
join:2007-02-05
Macomb, IL
| said by rcilink :1. Change HEX offset 23 from 4D to 4C. 2. Change the last four bytes to: AB 3A 49 5D Hey RC.
I have a question.
Do you suppose to include the very first byte when you do your math thing?
You might think it's weird that I ask, but look in the attachments, please.
Actually 4d byte is number 24, if you start counting from the very first one (43)...
Are the four bytes colored-circled in my attachment the last four you are talking about?
Thanks much. | |
|
| | rcilink
Premium
join:2003-12-15
Manchester, NH
| Re: Getting a WRTp54G to take 3.1.17-NA... That HEXedit software you are using wants to display (at the bottom) the current 'position', not the 'offset' value. The HEXedit software I use will tell me the offset at the bottom of the screen view.
The offset is supposed to be the number of bytes from the first byte. So, 23 bytes from the first byte is the "4D" in that firmware that gets changed to "4C".
Hope this helps you out. | |
|
| | | carmatt59
join:2007-02-05
Macomb, IL
| Re: Getting a WRTp54G to take 3.1.17-NA... said by rcilink :The offset is supposed to be the number of bytes from the first byte. Hope this helps you out. That makes sense, of course.
Tks. | |
|
| mikev6
join:2002-05-04
Herndon, VA
| Linksys updated their site, and no longer has the WRTP54G-NA listed as a model on their site. Will the RTP300 firmware work just as well (after the modifications of course), or will that firmware disable the wireless capability since the RTP300 doesn't have WiFi? | |
|
| | KillaB7
join:2006-05-23
Vancouver, BC
| Re: Getting a WRTp54G to take 3.1.17-NA... I know it's easy to modify NA firmware images to load onto our routers but has anyone tried changing the ProductID under PSPBoot?
I've enabled console access on my WRTP, but don't want to attempt any changes just yet.
»wiki.openwrt.org/OpenWrtDocs/Har···/WRTP54G
It might be as easy as simply changing the environment variable then rebooting. Or you may need to TFTP an NA image (matching ProductID) before rebooting??? | |
|
| kipa
join:2007-03-20
| Very nice site. I have my Vonage router unlocked!
Wov!
Does anyone know whether it works also for EARTHLINK ?
My friend asked me for advice - he has Earthlink dedicated WRTp54G router.
Thanks in advance for reply and again for HEX edit codes! | |
|
| | neoalex4
join:2006-06-01
Astoria, NY
| WRTP54g DST rule WRTP54g DST rule
Does anyone know what I should write in the DST rule in my Regional Settings on my WRTP54G. The rule should be:
* begins at 2:00 a.m. on the second Sunday of March and
* ends at 2:00 a.m. on the first Sunday of November
Please help thanks. | |
|
|
|
|
