rcilink
Premium
join:2003-12-15
Manchester, NH
| CYT Device: Unlocking Information I wanted to start a new thread here to help those who have a CYT-device and are trying to unlock and reuse it.
There are many CYT-flavored (TI AR7 chipset) devices.
Here are a few we know about:
- Linksys WRTP54G - 2 phone ports, 4 port router, wireless
- Linksys RTP300 - 2 phone ports, 4 port router
- Linksys PAP2 v2.0- 2 phone ports
- Vtech IP8100 - Cordless SIP phone with base
- Motorola VT2442 - 2 phone ports, 4 port router
- D-Link VTA-VR - 2 phone ports
- Linksys WAG54GP2 - 2 phone ports, DSL router
At this point, the cyt-unlocker being discussed in other threads will attempt to 'unlock' the device by changing the supervisor (Admin) password. The tool will also change all SIP settings to a generic default, making it ready for configuration by you.
As with many of these tricks, if you happen to factory reset the device, (most of the time) you will return all of the locked settings. This includes the factory setting of the Admin password.. it will be locked.
So, if you need to factory reset the device, just run the cyt-unlocker tool after the factory reset to re-unlock the device.
For those who are currently registered customers with a VoIP provider, this tool will not retain any of your account settings! In other words: do not use this tool if you are subscribing to a phone service! The device you are unlocking should not be registered with any service.
Current Version is: cyt 3.0 for Windows*
*See release notes in that file for currently supported devices.
As more devices are released with this chipset, newer versions will follow. From what I have heard, there has been talk about a web site going online to offer cleaner distribution of future updates.
The best support for owners of these devices is to use forums like this one. | |
|
 mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| Re: CYT Device: Unlocking Information To add more to the above, please read this CYT Device Unlock FAQ. Thi is a a must to read if you own a Linksys PAP2 v2.0 and/or a DLink VTA-VR device.
Credits go to cron for the FAQ.
--
Mazi (UK Non-Geo Phone: +44-703-194-2574) | |
|
 | DSLHeadaches
join:2001-01-03
Woodland Hills, CA
 ·AT&T U-Verse
 ·VoiceStick
 ·RoadRunner Cable
| Re: CYT Device: Unlocking Information I know it sounds stupid, and I've read about 2 hours through the various threads and haven't found the answer.
How do I obtain the IP Address of the PAP2 so that I can login while running CYT30 if I'm connecting between my PC and the PAP2 with a autosensing ethernet switch (as defined in the readme).
If I connect the PAP2 to my router, disconnecting the modem/Internet connection, then I can see the PAP2 IP address, can login to its web page, and can ping it. Attempts to run CYT30 in this configuration don't work, so I started to use the switch as defined in the CYT30 readme. Using the switch I cannot ping 192.168.15.1 or 192.158.1.5 (addresses suggested elsewhere). There is no DHCP, so how is the PAP2 obtaining the IP? | |
|
| | rcilink
Premium
join:2003-12-15
Manchester, NH | Re: CYT Device: Unlocking Information On the pap2 v2.0, there is IVR support.
That is, you can hook a phone to the line1 port and dial *** to get a voice menu.
Once in that menu, dial 110 # to hear your IP address read to you. | |
|
| | | DSLHeadaches
join:2001-01-03
Woodland Hills, CA
·AT&T U-Verse
·VoiceStick
·RoadRunner Cable
| Re: CYT Device: Unlocking Information Thanks rclink; however, since I have flashing power light, when I attach a phone to line 1 or 2 all I get is fast busy. There is no opportunity to access the IVR.
I'm a bit lost on the CYT30 readme, perhaps I just don't understand enough about networking. A switch, to my knowledge, has no methodology (NAT/DHCP) for assigning IP addresses. Thus when the readme is suggesting certain IP addresses, what is setting these? Do I need to install Internet Connection Sharing (ICS) on the desktop or do I specify for example the suggested IP addresses on the desktop (IPCONFIG?) and in the PAP2 configuration page (which currently is set to obtain IP). If I weren't using a switch and instead simply a cross-over cable I would have the same issue.
I am still able to login to the PAP2v2 by connecting it to my router (after unplugging the modem connection to avoid PAP2 connection to Vonage) and get to the config page. Running CYT30 in this setup (with my DHCP assigned IP) always results in the XML server starting, but nothing ever happens, it never comes back with a completion.
As an FYI, my PAP2 config page has a firmware version number like 1.0.13, yet I constantly see threads with firmware beginning with 3.x; am I missing something? Have I possibly created a door stop by doing a factory reset along the way?
I'm continuing to scan through the various threads on unlocking this beast. Perhaps I should use the original manual method of unlocking and forget about CYT30? | |
|
| | | | rcilink
Premium
join:2003-12-15
Manchester, NH
| Re: CYT Device: Unlocking Information said by DSLHeadaches  :I am still able to login to the PAP2v2 by connecting it to my router (after unplugging the modem connection to avoid PAP2 connection to Vonage) and get to the config page. Running CYT30 in this setup (with my DHCP assigned IP) always results in the XML server starting, but nothing ever happens, it never comes back with a completion. Sounds like it is working.. I would suggest that for the duration of using CYT that you disable windows firewall. If you do not, the device can not talk to the CYT tool.
Let us know if that helps. | |
|
| | | | | DSLHeadaches
join:2001-01-03
Woodland Hills, CA
·AT&T U-Verse
·VoiceStick
·RoadRunner Cable
| Re: CYT Device: Unlocking Information Factory Reset (hold reset button > 20 sec lights blink). Numerous attempts and no change in attempting to reach IVR. Either silence on line, a three rising tone, or fast busy; but no response to any of asterisk button and varying states of the above three states.
Turned off Norton Int Sec completely and no Windows Firewall (as done previously), reset Int Explorer security settings to Low on Internet and Local Low. Logged into PAP2 admin/admin. CYT30 changed to IP address which is used to access. XML server started, but never returns. Factory reset via reset button didn't help. Didn't try just the ethernet switch since obtaining the IP via IVR didn't seem possible. Did try changing PAP2 to hardcode the IP address assigned by router.
Perhaps I'll try CYT30 on another computer tomorrow. | |
|
| | | | | | DSLHeadaches
join:2001-01-03
Woodland Hills, CA
·AT&T U-Verse
·VoiceStick
·RoadRunner Cable
| Re: CYT Device: Unlocking Information I was able to utilize another computer and CVT30 completed providing login info as designed. There must be some form of software blocking completion on my primary computer, the successful computer has almost nothing loaded.
I can now access the IVR, obtain IP and even have dialtone.
However, all attempts to login to Update or Voice_admin failed with "Error: User not allowed to login this user level" or "Bad User/Password". I've tried all sorts of combinations, power cycled the PAP2, tried normal login, followed by the /update page with no success (noting that it accepts the factory user/password at just the IP home page) and tried rerun CVT30 (all with internet diconnect). I'll keep trying... | |
|
| | | | | | | mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| Re: CYT Device: Unlocking Information said by DSLHeadaches :However, all attempts to login to Update or Voice_admin failed with "Error: User not allowed to login this user level" or "Bad User/Password". Once unlocked using CYT30 unlocker, use Admin/Admin combination to login to VM and/or perform firmware upgrade.
--
Mazi (UK Non-Geo Phone: +44-703-194-2574) | |
|
| | | | | | | | DSLHeadaches
join:2001-01-03
Woodland Hills, CA
·AT&T U-Verse
·VoiceStick
·RoadRunner Cable
| Re: CYT Device: Unlocking Information Thanks mazilo & rcilink, I'm in and able to use Internetcalls.com for callout. Trying to determine SIP inbound and whether it will work. Obtained copy of xml file with provisioning. Hoping to try skype using the SIP intermediary tool. Hoping to figure out best CODECs since Internetcalls has bad echo for callee, as others have mentioned. Tried setting Echo Cancellation, we'll see if that helps. | |
|
| | | | | | | | | mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
1 edit | Re: CYT Device: Unlocking Information said by DSLHeadaches :Hoping to try skype using the SIP intermediary tool. I believe you will need also need asterisk to do this unless the intermediary tool (uplink?) can do this by itself, won't you?
--
Mazi (UK Non-Geo Phone: +44-703-194-2574) | |
|
| | | | | | | | | 
nukleuz
Premium
join:2006-07-23
Columbia, MD
2 edits | Re: CYT Device: Unlocking Information i got it working too on the RTP300 trying to figure out what to use for incoming calls like how to get a number for incoming calls and all that.if anyone has been able to do that please let us know
thank you | |
|
| | | | | | | | | kgu2206
join:2005-10-03 | Re: CYT Device: Unlocking Information Any lucky to unlock with D-Link VTA-VR device?
Thanks | |
|
| | | | | | | | | mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| said by nukleuz :i got it working too on the RTP300 trying to figure out what to use for incoming calls like how to get a number for incoming calls and all that. Check out StanaPhone.
--
Mazi (UK Non-Geo Phone: +44-703-194-2574) | |
|
| | | | | | | | |
nukleuz
Premium
join:2006-07-23
Columbia, MD | Re: CYT Device: Unlocking Information ok thnx | |
|
| | | | | | | | | |
| | | | | | netmitra
join:2006-09-28
Sunnyvale, CA | Hi;
Was anybody able to unlock WRTP54G using cyt. I tried hard, but not luck | |
|
| | | | | | | netmitra
join:2006-09-28
Sunnyvale, CA
| Cant Unlock WRTP54G Please help.
I am using cyt39c to unlock a Vonage WRTP54G with firmware 1.00.20. The cyt screen gets stuck here for ever.
____________________________________________________
CYT-Unlocker - Local network version v3.9c
Simple XML provision server is waiting for your device..
This should only take up to one minute.
If it takes more than one minute, you may stop the XML
provision server by pressing the [ESC] key.
----------------------------------------------------------
Press [esc] to exit.
STATUS: XML Server started. Your Device is: WRTP54G | |
|
| | | | | | | | 
campbeln
@co.uk | Re: Cant Unlock WRTP54G I'm having the same issue, anyone have a resolution to this one? | |
|
| | | | | | | | |
| | | | | | | |
campbeln
@co.uk | Re: Cant Unlock WRTP54G Agh, just remember to try and use the "user" account (with a default password of "tivonpw") if /update.html doesn't play nice for you! | |
|
| | | | | | | | | netmitra
join:2006-09-28
Sunnyvale, CA | Re: Cant Unlock WRTP54G No Luck;
My WRTP54G wont understand user: tivonpw.
THe only login I have is admin:admin | |
|
| | | | | | | | | mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| Re: Cant Unlock WRTP54G said by netmitra :My WRTP54G wont understand user: tivonpw. tivonpw is the user password assigned by Vonage. You will need to have your WRTP54G provisioned by Vonage once in order for it to recognize tivonpw assuming tivonpw is still the password used/assigned by Vonage.
--
Mazi (UK Non-Geo Phone: +44-703-194-2574) | |
|
| | | | | | | | | netmitra
join:2006-09-28
Sunnyvale, CA
| WRTP54G Unlocked ---- Thank you guys !! After 1 week of attempts - Success now.
I was successfully able to unlock my Vonage WRTP54G using the firmware upgrade procedure. THe cyt software failed to do so. I used the following link and it worked like charm !
»Getting a WRTp54G to take 3.1.17-NA...
My router wasn't accepting any user:tivonpw password and I was stuck. Then I did a factory reset using the poke-in button at the back. After that I was able to access update.html and then upgraded the firmware. Now I am on 3.1.17 and life feels good. Configuring VIatalk was a cakewalk.
Next Project is to install astersik on this. ANy easy-2-go guide will be appreciated. | |
|
| | | | | | | | | mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| Re: WRTP54G Unlocked ---- Thank you guys !! said by netmitra :Next Project is to install astersik on this. ANy easy-2-go guide will be appreciated. Porting asterisk to this router seems to be OK; however, making asterisk to work with ggsip is a bit of challenging. One way to resolve this problem is to replace ggsip with zaptel, but it ain't going to be an easy task.
--
Mazi (UK Non-Geo Phone: +44-703-194-2574) | |
|
| | | | | | | | deskjockey
join:2005-04-17
Charlotte, NC | I had the same problem with Vonage D-Link. I went back to the CYT 3.5 and worked like a charm. | |
|
| | | | | | | | MartyT
join:2004-09-03
Georgetown, SC
1 edit | Is there something unique about the WRTP5G with stock firmware 1.00.20 that keeps it from being unlocked using any version of CYT?
One other person mentioned no luck with this original firmware.
Anyone else? Any solutions? I tried turning off the wireless as suggested on some Vonage forums, but no luck.
This is a virgin unit, never registered with Vonage, straight out of a sealed box. | |
|
| | | | | | | | | rcilink
Premium
join:2003-12-15
Manchester, NH
| Re: Cant Unlock WRTP54G said by MartyT :Is there something unique about the WRTP5G with stock firmware 1.00.20 that keeps it from being unlocked using any version of CYT? CYT will not work with the 1.00.20 firmware..
A suggested solution (if it had previously been used with vonage):
1. Hook your WRTP54G with 1.00.20 firmware to the Internet
2. Press and hold reset using a paperclip in the pinhole on back
3. Apply power to device
4. After about 40 secs, lights will all blink. Remove paperclip
5. Let it sit there, on the Internet. It should get new firmware (1.00.62)
* Unlike the Linksys PAP2 (v1) and Sipura products, it is OK to let this one upgrade to the 1.00.62 firmware.
6. You can open a web browser and check the built-in page (top right) to see what firmware is loaded.
7. Use CYT (3.5 is reportedly more stable) to unlock it when it is 1.00.62. | |
|
| | | | | | | | | MartyT
join:2004-09-03
Georgetown, SC
| Re: Cant Unlock WRTP54G This is a virgin router, out of the box, never registered with Vonage.
There are lots of them floating around like this that are being sold on Ebay, which is where I got mine.
Any solution on how to get them upgraded without subscribing to Vonage? | |
|
| | | | | | | | | mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| said by MartyT :Is there something unique about the WRTP5G with stock firmware 1.00.20 that keeps it from being unlocked using any version of CYT? Can you perform a firmware upgrade? If so, then you can unlock this beast and perhaps completely remove Vonage, a.k.a. turn it into a WRTP54G-NA.
Anyone else? Any solutions? I tried turning off the wireless as suggested on some Vonage forums, but no luck. I never heard of this trick.
This is a virgin unit, never registered with Vonage, straight out of a sealed box. As rcilink has already pointed out and unless you can perform a firmware upgrade, you will need to let this unit phone home to Vonage so that it will get provisioned with a known user password, i.e. tivonpw (unless Vonage has recently changed this to a new one), then use this user/tivonpw to perform a firmware upgrade (chances are Vonage will have pushed in for a new firmware).
--
Mazi (UK Non-Geo Phone: +44-703-194-2574) | |
|
| | | | | | | mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| Re: CYT Device: Unlocking Information said by netmitra :Was anybody able to unlock WRTP54G using cyt. I tried hard, but not luck Can you perform a firmware upgrade on your WRTP54G? If so, then you can flash it with a modded -NA firmware.
--
Mazi (UK Non-Geo Phone: +44-703-194-2574) | |
|
| |
| | skypeuser
join:2005-03-08
United State
·Axvoice
| Re: CYT Device: Unlocking Information I had this problem and was able with the advice in this thread to load 3.1.17 firmware. I hooked up my WRTP54G to the Internet wan port. I left it there for a couple of hours. When I logged into the web interface it had updated to 1.00.62 firmware. From there I was able to log into the /update.html page and upgrade and unlock this device.
You will need to be patient, but this will work. I have done this as have several others in this thread.
Good Luck!  | |
|
| | | |
mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| Factory reset your PAP2v2 and see if that will do the trick. Please don't say you don't know how to factory reset your PAP2v2. 
--
Mazi (UK Non-Geo Phone: +44-703-194-2574) | |
|
tpgopi
join:2003-03-07
Bloomington, IL
clubs: | Did anybody successfully unlocked WRTP54G or RTP300 using this tool? | |
|
kenjreno
join:2006-08-29
Sparks, NV
| I'm trying to see if the CYT has been able to Unlock a VTec 8100. BB had them on clearance here for $40 for the 8100-2, and I would like to get them configured for my Asterisk Box.
Every time I try it, i get the message that I must be logged into the unit. I'm logged in, and have it pointing to the correct address, but still no luck getting it to reset the information. Any help would be great. I can even help test the unlocking if that is also a possibility. | |
|
rcilink
Premium
join:2003-12-15
Manchester, NH
1 edit | It looks like a new version of CYT is ready for release..
News about this release:
- Includes support for Motorola VT2442 (and similar ?) units.
Who knows.. maybe it will just work with D-Link VTA-VR too? | |
|
|
K
@bellsouth.net | Re: CYT Device: New Release : v3.3 includes Motorola vt2442 !! " Who knows.. maybe it will just work with D-Link VTA-VR too? "
I knew it is coming soon..because I saw you bought a VTA-VR on e-Bay.. | |
|
| |
nukleuz
Premium
join:2006-07-23
Columbia, MD
| Re: CYT Device: New Release : v3.3 includes Motorola vt2442 !! i have a pap2 i bought from best buy 2 years ago i believe and i used with vongage.Now i had vonage discontinue my service and i'm trying to unlock it and try some other VOIP services out there but for some reason when i connect the device to my laptop,it does not pull a gateway therefore i cannot enter the router to even begin unlocking it
i used to have an RTP300 i unlocked with no problems a few years back and i gave that to a friend because i thought it was a little bulky now i have this cute one giving me problems
Does anyone know why i cant get into this router or how i should go about this?
--
cpu:quadcore QX6700
video card:evga 8800gtx
mobo:asus striker extreme
ram:2gb dominator pc2 8500c5d
monitor:24" dell ultrasharp
psu:620w enermax infinity | |
|
RonR
join:2003-10-10
Downey, CA
| Kaspersky AntiVirus is very unhappy with the latest file:
Kaspersky Anti-Virus 6.0
The requested URL »/r0/download/1···in32.zip is infected with Trojan-PSW.Win32.LdPinch.aux virus
Anyone else getting warnings? | |
|
| rcilink
Premium
join:2003-12-15
Manchester, NH
1 edit | Re: CYT Device: Unlocking Information said by RonR :Kaspersky AntiVirus is very unhappy with the latest file: Kaspersky Anti-Virus 6.0 The requested URL » /r0/download/1···in32.zip is infected with Trojan-PSW.Win32.LdPinch.aux virus Anyone else getting warnings? Interesting.. I will scan here and see what comes up.. Hopefully nothing, but will do that just to make sure as well.
EDIT: I just completed the full virus-scan and it did not show anything.. I am hoping that your software shows it as false-positive.. Anyone else see this problem with cyt? | |
|
| | myvoip07
join:2006-04-29
USA
·VOIPo
| Re: CYT Device: Unlocking Information said by rcilink :Anyone else see this problem with cyt? Checked both versions with norton and nada here.. | |
|
| mrvoice
join:2001-02-22
Northridge, CA | I'm running 6.0 and no problem here. Downloaded, extracted, and ran without interuption. | |
|
| | mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| Re: CYT Device: Unlocking Information said by mrvoice :I'm running 6.0 and no problem here. The latest CYT is v3.9c. What is 6.0 you mentioned here?
--
Mazi (UK Non-Geo Phone: +44-703-194-2574) | |
|
rcilink
Premium
join:2003-12-15
Manchester, NH
1 edit | I have no idea why the cyt33 was triggering your AV.. According to google, that trojan is brand new. Since I have used the program here, I did a thorough scan and did not find anything to report.
Anyhow, here is a cleaned-up version that (maybe) includes d-link VTA-VR support.. someone should test it and verify that for us.
Also, this version has a preview of an upcoming menu... It will (soon) let you make changes to the XML using cyt. There are many settings that are not shown on the web interfaces of these devices. What better way to access those settings? (it gives you a sneak-peak for now, does not let you make changes at this time)
EDIT: The cyt_3.4 version has been removed-- it has a port error, preventing it from doing anything. It has been corrected, and re-packaged as cyt_3.5. If you downloaded the 3.4 release, please re-download this link (updated to 3.5). | |
|
|
See 9 replies to this post |
|
elvisk
join:2003-08-17
Boston, MA
| I just tried it on the Dlink and it gets "failed to connect to device." Should I have provisioned it first? I did unlock it but reset to defaults to try out the cyt_34 version. I think it's getting closer to working. Let me know if I can test it more.
EK | |
|
tastyratz
join:2006-07-24
Nashua, NH
| FWIW I tried version 33 on my vonage pap2 2.0 and it did not work. It gave me a successful message and thought it worked, but after some time and power cycling still no actual results. I switched back to 30 and was able to unlock however so perhaps something changed? | |
|
SteveLV702
Premium
join:2004-04-22
Henderson, NV | grr this totally sucks this program doesn't work for me either cause you have to open the web gui and mine is disabled and tried to enable it via the IVR but it asks for the admin password which I do not know... :'( | |
|
| mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| Re: CYT Device: Unlocking Information said by SteveLV702 :grr this totally sucks this program doesn't work for me either cause you have to open the web gui and mine is disabled and tried to enable it via the IVR but it asks for the admin password which I do not know... :'( Factory reset your device and don't let it connect to the Internet.
--
Mazi (UK Non-Geo Phone: +44-703-194-2574) | |
|
SteveLV702
Premium
join:2004-04-22
Henderson, NV | kind of hard to do when there is no factory reset button and when you try to do it via the IVR it asks for the admin password which I do not know... | |
|
| rcilink
Premium
join:2003-12-15
Manchester, NH
| Re: CYT Device: Unlocking Information It is sounding like you are talking about the original Linksys PAP2 device. Sorry to say, the original PAP2 does not work with the CYT program.
Probably about one month ago, Linksys PAP2 v2.0 started to show-up on the shelves at stores around the country. Even though it is labeled "Linksys PAP2 v2", it is really a completely different beast inside. That is why the v2 version works with the CYT program.
The v2 version of the PAP2 does indeed have a reset button. Holding it in for the 30sec to 1 minute timeframe will actually factory default the device.
One option you have, if your purchase was recent, would be to return it and look for the "v2" version of the PAP2. The PAP2 box has a silver stripe on the top-front for v2. (The original has orange stripe)..
New packaging looks like this:
and... Old packaging looks like this: | |
|
| mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| said by SteveLV702 :kind of hard to do when there is no factory reset button and when you try to do it via the IVR it asks for the admin password which I do not know... A PAP2v2 has a built-in reset PIN hole to do a factory reset. If yours don't have a reset PIN hole on the side panel and above Phone1 port, then it is either an ordinary PAP2 or a PAP2T (if this one also has no reset PIN hole, too).
--
Mazi (UK Non-Geo Phone: +44-703-194-2574) | |
|
SteveLV702
Premium
join:2004-04-22
Henderson, NV | well on the device it says v2 | |
|
SteveLV702
Premium
join:2004-04-22
Henderson, NV
 ·Clearwire
1 edit | Here is picture of our boxes. sorry bad quality was taken with my cell phone in a somewhat dark room. | |
|
| mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| Re: CYT Device: Unlocking Information said by SteveLV702 :Here is picture of our boxes. sorry bad quality was taken with my cell phone in a somewhat dark room. Those boxes looked like PAP2v2. Please confirm the MAC address of on the BOXes with the ones on the back panels of your PAP2v2 units. They should match. Then, there should be a reset PIN hole on the left side panel above Phone1 port. You may need a magnifying glasses to see.
--
Mazi (UK Non-Geo Phone: +44-703-194-2574) | |
|
SteveLV702
Premium
join:2004-04-22
Henderson, NV | Its a PAP2-NA version 2 it has no reset button/hole anywhere on the outside of the device or on the inside of the device. It shows date made was 03/2006 | |
|
| mrvoice
join:2001-02-22
Northridge, CA
| Re: CYT Device: Unlocking Information I thought the PAP2-NA is unlocked by default. I do know service providers will ship the pap2-na and lock you out. Voicepulse does this for instance. Though I have Never seen a PAP2-NA on a retail shelf. I'm not seeing alot of PAP2's anymore, but the earthlinks are flooding the shelves. I wonder what Earthlink's policy is after you cancel their service? Will they let you unlock the box?
Anyway, that is my 2 cents on the NA version. makes sense to me. | |
|
| |
SteveLV702
Premium
join:2004-04-22
Henderson, NV | Re: CYT Device: Unlocking Information it is unlocked by default but Ionosphere.net shipped them to me locked. | |
|
|
| rcilink
Premium
join:2003-12-15
Manchester, NH
1 edit | Re: CYT Device: Unlocking Information If your PAP2 v2 was of the latest flavor (TI chip inside), it would have a reset button, as shown.
My guess would be that those are Linksys PAP2 units, based on the Sipura model. That is similar (if not the same) to the original Linksys PAP2 unit.
Out of curiousity, can you dial into the IVR (***) and then check what firmware it is using? | |
|
| |
SteveLV702
Premium
join:2004-04-22
Henderson, NV | Re: CYT Device: Unlocking Information firmware is 3.1.8 | |
|
| | | mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| Re: CYT Device: Unlocking Information said by SteveLV702 :firmware is 3.1.8 I have opened up several PAP2v2 and they all had v1.00.13 firmware. See the right=hand corner on attached picture where it shows firmware version of 1.00.13.
--
Mazi (UK Non-Geo Phone: +44-703-194-2574) | |
|
| | | |
SteveLV702
Premium
join:2004-04-22
Henderson, NV | Re: CYT Device: Unlocking Information well my ivr says 3.1.8 I don't have a web gui so can't verify that way. | |
|
| | | | | mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| Re: CYT Device: Unlocking Information said by SteveLV702 :well my ivr says 3.1.8 I don't have a web gui so can't verify that way. Unlike a PAP2, a PAP2v2 MAC address starts out with 0018. I know you already mentioned your PAP2v2 has a V2 on it somewhere, can you look very carefully again to see if there is a written PAP2V2 on the back of your device? Also, if you look from the front side, where can the Cisco logo be found? BTW, on your post where you mentioned it's a PAP2-NA version 2 it has no reset button/hole anywhere on the outside of the device or on the inside of the device. Which device did you refer to as a PAP2-NA v2?
--
Mazi (UK Non-Geo Phone: +44-703-194-2574) | |
|
SteveLV702
Premium
join:2004-04-22
Henderson, NV
·Clearwire
| well all 3 of mine MAC Address starts out at 0016 and regardin g the cisco logo its on the oposite end from the popoff cover for where the feet go.
and PAP2-NA v2 are the only device I have
and on bottom of device it says
Model No: PAP2-NA v2 | |
|
| mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| Re: CYT Device: Unlocking Information said by SteveLV702 :and PAP2-NA v2 are the only device I have and on bottom of device it says Model No: PAP2-NA v2 I am lost here. I thought you want to find out if you had a PAP2v2, didn't you? If so, your last chance is to open up the box, look inside, take some snapshots of inside view (this time please post some nice pictures!), and tell us what you see.
--
Mazi (UK Non-Geo Phone: +44-703-194-2574) | |
|
| |
SteveLV702
Premium
join:2004-04-22
Henderson, NV
·Clearwire
| Re: CYT Device: Unlocking Information no mazilo I said I have a PAP2-NA V2 I am just trying to get it unlocked. By default its unlocked by IonoSphere.net put in an admin password and disabled the webgui so now its locked. And since I dont see any reset button I can't even reset it..
I'll take some pictures of the inside but nice pictures I doubt that since my digital camera battery is totally shot to hell. So as of right now I can only take pictures with my cell phone. | |
|
SteveLV702
Premium
join:2004-04-22
Henderson, NV | but anyway as of now I am going to go try this on my old vonage Motorola VT2442 Router. Afterwords where do I go to access the voice setttings? | |
|
| rcilink
Premium
join:2003-12-15
Manchester, NH | Re: CYT Device: Unlocking Information In Motorola, SIP settings are under the ADVANCED tab.. | |
|
SteveLV702
Premium
join:2004-04-22
Henderson, NV
·Clearwire
| well this tool doesn't work for the Motorola VT 2442 either as I logged into the webgui via »192.168.15.1 Username: router Password: router and then ran the CYT Program and pressed 3 and entered the IP 192.168.15.1 and then did 1 and comes back saying something about some Security Access Violation that I need to login via my web browser which I already did. | |
|
| rcilink
Premium
join:2003-12-15
Manchester, NH
1 edit | Re: CYT Device: Unlocking Information which version of cyt are you using..?
only version 3.5 or newer will work with the motorola and d-link models.
Click this link to download CYT version 3.5 for windows. | |
|
SteveLV702
Premium
join:2004-04-22
Henderson, NV | okay I was running 3.0 but I downloaded the 3.5 and still isnt working still giving me security access violation need to login via browser even though I already am. | |
|
| rcilink
Premium
join:2003-12-15
Manchester, NH
| Re: CYT Device: Unlocking Information said by SteveLV702 :okay I was running 3.0 but I downloaded the 3.5 and still isnt working still giving me security access violation need to login via browser even though I already am. What does it report on your screen (look at the bottom-right of the screen) for the Device: identification? | |
|
SteveLV702
Premium
join:2004-04-22
Henderson, NV
·Clearwire
| dont see anything about Device: identification
attached is a screen shot | |
|
|
|
|
ANY IDEA???
Re: CYT Device: Unlocking Information
