toro
join:2006-01-27
Scarborough, ON
 ·TekSavvy Solutions..
| reply to jwx213
Re: D-Link firmware 1.00.08 ... how to unlock it...
said by jwx213  :The only way i got it to work was to use the serial console and the command fmt CONFIG_A if my memory is correct then fmt CONFIG_B Thanks for the info, I'll try it. Did you run those commands at the boot loader prompt or after the box has booted up ?
From my understanding, the adapter keeps 2 versions of the firmware (and configuration). How can I tell which is the one in use ? And how can I make both the same ? |
|
jwx213
join:2006-08-27
Leicester,UK
| At the boot loader prompt, not after boot!
I formated both IMAGE_A + B and CONFIG_A + B. Then tftp'ed the firmware to IMAGE_A + B under serial console, Then did the SSH bit after that.
To check which image the box is booting from type either:
cat /proc/ticfg/env or printenv
Cant remember which without doing it! As long as you flash IMAGE_A + B under the serial console, it doesnt matter anyway, they will both be NA modded firmware 
Before trying to TFTP firmware under serial console, dont forget to hex edit it as per rcilink's comments here : »Re: VTA failsafe - recovery options
Should sort ya box out!  |
|
scsikid
join:2007-01-20
555555
| reply to jwx213
Re: vta 1.00.08 firmware
I tried this with VTA-11.4.0-r060331-1.00.08-r061127.img so far it is working. I see that the default vonage settings are gone which is great. I tried setting everything to default settings and still mine remain in /proc/ticfg/env and the corresponding webpage. I will see how it is in 24hrs as prior to trying this, it would reset to some defaults and my VoIP settings would be lost.
Thanks..... so far!
just wanted to make sure, the NA2a firmware that people are talking about, is in fact the one im using? VTA-11.4.0-r060331-1.00.08-r061127.img i did upgrade the firmware and the adapter said successful. ???? can someone confirm this? |
|
jwx213
join:2006-08-27
Leicester,UK | You cant tell with the actual numbers, as the modded FW is the 1.08 vonage FW image.
Make sure you downloaded off the Rapidshare link on the previous pages |
|
toro
join:2006-01-27
Scarborough, ON
·TekSavvy Solutions..
| reply to jwx213
Re: D-Link firmware 1.00.08 ... how to unlock it...
I flashed both images of the VTA last night from the boot loader, as well as I deleted both configurations. Then I tried again to set my own factory settings, but the only one that works is the Admin password, and that is from the web interface only (still doesn't work from SSH). The Admin password works for SSH only if I provision the adapter with an XML file. |
|
toro
join:2006-01-27
Scarborough, ON | reply to rcilink
Can someone build (or teach me how to build) unlocked firmwares for other CYT based firmwares ? I have a couple of VTech IP8100's around, and a Motorola 2142. |
|
mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| said by toro :I have a couple of VTech IP8100's around, and a Motorola 2142. Both VTech and Moto are bound by GPL to release their GPLed firmware code. If they haven't done so, you may want to contact them to let them know about GPL licensing schemes. On any GPLed firmware package, it should include the Makefile scripts to package the compiled code into a firmware. You can take a look at and study on these Makefile(s) scripts and make your own script to extract/compress the code into a firmware.
--
Mazi (UK Non-Geo Phone: +44-703-194-2574) |
|
scsikid
join:2007-01-20
555555
| reply to jwx213
Re: vta 1.00.08 firmware
thanks jwx213. all seems ok, however now my digit map (dial map) doesnt seem to save. i set it via ssh
/usr/bin/dbgcmd
MXP> show tcid 0
Dial In Parameters:
Plar addr: None
Digit Map: *xxT|*1xx|[349]11|1xxx[2-9]xxxxxx|[2-9]xxxxxxT|[2-9]xxxxxxxxx|011x.T
MXP> set tcid 0 dial_in digit_map *xxT|*1xx|[349]11|1xxx[2-9]xxxxxx|[2-9]xxxxxxT|[2-9]xxxxxxxxxx|011x.T
MXP> OK
MXP> commit
MXP> OK
MXP> activate
MXP> OK
this dial plan works for me because i have to dial 9 before the area code and allows the last digit to be entered. however after a reboot, this digit map is lost. i have tried entering it in the web page via firefox and internet explorer and it still wont save after a reboot.
help? |
|
Luboso
join:2007-01-14
| said by scsikid : Guys,
-I exposed my VTA to internet,
-had it provisioned by vonage,
-took it off the web
-downgraded to f/w 1.00.7
-grabbed the encrypt code and the directory of .xml file
-tftp-ed the .xml file from vonage and decrypted it with rc4
-I have the factory Admin password now and upgraded f/w to 1.008-NA provided by rclink (BTW thanx for that)
-now the settings seem to stick in the voicebox, except the small technical parameters.
Now can someone help me to get rid off the 666 that the unit automatically dials after picking up of the hand set?
If I understand it correctly from this forum, a modified .xml file needs to be uploaded to the unit. Is that correct? Why? I got this file from the vonage server. How would I want to change it and how would I want to push it to the VTA? |
|
scsikid
join:2007-01-20
555555
| reply to scsikid
does this happen to anyone else? after about 10 hours or so my vta-cv goes offline (not reachable) both configured phone 1 and phone 2 ports go offline. only a reboot by unplugging the device brings everything back to normal. i think i'll try a packet capture and see if i can notice any network activity going on the device before it fails. if anyone has any advise please let me know. |
|
plasmafans
join:2007-01-02
Vancouver, BC
| said by scsikid :does this happen to anyone else? after about 10 hours or so my vta-cv goes offline (not reachable) both configured phone 1 and phone 2 ports go offline. only a reboot by unplugging the device brings everything back to normal. i think i'll try a packet capture and see if i can notice any network activity going on the device before it fails. if anyone has any advise please let me know. I have the same problem but with shorter live time. It only works 4 hours. I almost give up.  |
|
jwx213
join:2006-08-27
Leicester,UK
| I think the 1.08-NA modded FW still needs messing with.
It doesnt do everything yet, and the problem with clearing factory defaults can be frustrating. I did my box by messing for hours until it saved.
As for tech settings in line 1 & 2 under the web interface, they dont save on my box at all.
I havent noticed it disconnect my lines though. Have 2 x Sipgate accounts setup in it and its been running for 14 days no problem.
I still think its a case of mess around and keep an eye out for FW changes. The box is good hardware and when working is great, the FW is slowly catching up with it! I had a D-Link wireless media player which had good hardware, but until people messed with its FW was useless.
Hang in there, it will get better.... |
|
gAfaS
@bulldogdsl.com |  reply to mazilo
Re: [General] DLink VTA-UV
Dear mazilo,
yes i did but it didnt work so I just managed to buy the linksys 2102 which took me around 4 hours to make it work but now it is working absolutely fine.
Thanks a lot again! |
|
scsikid
join:2007-01-20
555555 | reply to jwx213
Re: vta 1.00.08 firmware
how about the older firmware, version 7. does it retain its settings and not reboot periodically? i dont mind using it, just need some stability. if so, does anyone have a link for the old firmware? |
|
scsikid
join:2007-01-20
555555 | reply to plasmafans
ya actually i was off, its 4 to 5 hours. |
|
jwx213
join:2006-08-27
Leicester,UK
4 edits | reply to scsikid
Here are the links to the firmware files and CYT....
1.00.07 - Vonage locked - »httpconfig.vonage.net/VTA-11.4.0···-r060418
1.00.08 - Vonage locked - »httpconfig.vonage.net/VTA-11.4.0···-r061127
1.00.08NA - Unlocked Modded FW - »rapidshare.com/files/9362834/vta···NA2a.bin |
|
plasmafans
join:2007-01-02
Vancouver, BC
| reply to scsikid
said by scsikid :ya actually i was off, its 4 to 5 hours. Any solution? |
|
rcilink
Premium
join:2003-12-15
Manchester, NH
| My guess:
- hook up the serial console cable, and leave a term program open...
- check the VTA often to see if it crashed.
- once crashed, scroll carefully thru the console messages.. It will tell you what it is doing and what happened.
For example: I have seen these devices attempt to 'default' to factory provision if they are not able to provision with new params. That said, if you are using that 1.00.08-NA, you can change default Factory Params-- that might keep it from changing SIP info on you.
Good Luck! |
|
hieppo
join:2004-12-01
Etobicoke, ON
| reply to rcilink
Re: [General] DLink VTA-VR
said by rcilink :said by jwx213 :On a different subject, has anyone found a way or got any closer to installing PAP2v2 Firmware on the D-Link box as it would make setup so much easier than the D-Link pants firmware? Yes, it has been done. I will put some of the guidelines here if you dare to take similar steps with your equipment: You really need to have a serial console cable hooked to the device for this to succeed! 1. Crack open the D-Link VTA-VR and hook up your serial cable to your com port. Remember, it is 3.3v, so use the proper chip (dont just hook it up directly!) 2. On the D-Link VTA-VR, you can simply hit ESC (on the serial console session) when you first boot the device. This will give you the psbl prompt. 3. At this prompt, you will need to delete all flash partitions, except the bootloader (pspboot). 4. Create new partitions, matching the ones found on the Linksys PAP2 v2.0. 5. Add the needed ENV variables while using psp boot. This is important. Just copy them from a PAP2 v2.0 and change unique info (MAC, IP, etc.) to match D-Link VTA-VR. 6. On a PC or Linux box, hexedit the 1.00.13 .bin firmware file and change Location 0x000B byte from 0xFF to 0x17. (This will make psp boot take the file) 7. Use the psp boot TFTP option to load-up the firmware .bin file to the proper partion (there are 2 if you want a backup partition pre-loaded, you must load it). 8. set the PSPBOOT env variables to point to the proper boot partition (BOOT_CFG.. ) 9. Done. The hardware is mildly different, making the LEDs not work, so you do not get any blinky lights as you use the thing. But, the web interface works, and you can work away. Also, I dont remember the ADMIN_PWD being set.. You may need to set it to something. (It is a Unix passwd hash). NOTE: My testing did not include setting-up any SIP service on this VTA-VR running PAP2v2 firmware. At the time, that was not in the test schedule. If I have time, I will try it again and report results here. ------ rcilink or anyone out there, could someone tell me what are the PAP2 v2.0 environment settings? I would like to know about the partition on the PAP2 v2.0. I really want to play with loading the PAP2 v2.0 firmware on the DLINK. I want to be able to make create Quick Dial. Thanks |
|
javacocoon1
@myvzw.com | Does anyone know if NA2a (mod firmware) allows username to have alphabets ? like galaxyvoice usernames that start with R ? I tried with the stock firmware and it did NOT work. Appreciate response. |
|
