DSLHeadaches
join:2001-01-03
Woodland Hills, CA
 ·AT&T U-Verse
 ·VoiceStick
 ·RoadRunner Cable
| reply to mazilo
Re: CYT Device: Unlocking Information
I know it sounds stupid, and I've read about 2 hours through the various threads and haven't found the answer.
How do I obtain the IP Address of the PAP2 so that I can login while running CYT30 if I'm connecting between my PC and the PAP2 with a autosensing ethernet switch (as defined in the readme).
If I connect the PAP2 to my router, disconnecting the modem/Internet connection, then I can see the PAP2 IP address, can login to its web page, and can ping it. Attempts to run CYT30 in this configuration don't work, so I started to use the switch as defined in the CYT30 readme. Using the switch I cannot ping 192.168.15.1 or 192.158.1.5 (addresses suggested elsewhere). There is no DHCP, so how is the PAP2 obtaining the IP? |
|
rcilink
Premium
join:2003-12-15
Manchester, NH | On the pap2 v2.0, there is IVR support.
That is, you can hook a phone to the line1 port and dial *** to get a voice menu.
Once in that menu, dial 110 # to hear your IP address read to you. |
|
DSLHeadaches
join:2001-01-03
Woodland Hills, CA
·AT&T U-Verse
·VoiceStick
·RoadRunner Cable
| Thanks rclink; however, since I have flashing power light, when I attach a phone to line 1 or 2 all I get is fast busy. There is no opportunity to access the IVR.
I'm a bit lost on the CYT30 readme, perhaps I just don't understand enough about networking. A switch, to my knowledge, has no methodology (NAT/DHCP) for assigning IP addresses. Thus when the readme is suggesting certain IP addresses, what is setting these? Do I need to install Internet Connection Sharing (ICS) on the desktop or do I specify for example the suggested IP addresses on the desktop (IPCONFIG?) and in the PAP2 configuration page (which currently is set to obtain IP). If I weren't using a switch and instead simply a cross-over cable I would have the same issue.
I am still able to login to the PAP2v2 by connecting it to my router (after unplugging the modem connection to avoid PAP2 connection to Vonage) and get to the config page. Running CYT30 in this setup (with my DHCP assigned IP) always results in the XML server starting, but nothing ever happens, it never comes back with a completion.
As an FYI, my PAP2 config page has a firmware version number like 1.0.13, yet I constantly see threads with firmware beginning with 3.x; am I missing something? Have I possibly created a door stop by doing a factory reset along the way?
I'm continuing to scan through the various threads on unlocking this beast. Perhaps I should use the original manual method of unlocking and forget about CYT30? |
|
rcilink
Premium
join:2003-12-15
Manchester, NH
| said by DSLHeadaches  :I am still able to login to the PAP2v2 by connecting it to my router (after unplugging the modem connection to avoid PAP2 connection to Vonage) and get to the config page. Running CYT30 in this setup (with my DHCP assigned IP) always results in the XML server starting, but nothing ever happens, it never comes back with a completion. Sounds like it is working.. I would suggest that for the duration of using CYT that you disable windows firewall. If you do not, the device can not talk to the CYT tool.
Let us know if that helps. |
|
DSLHeadaches
join:2001-01-03
Woodland Hills, CA
·AT&T U-Verse
·VoiceStick
·RoadRunner Cable
| Factory Reset (hold reset button > 20 sec lights blink). Numerous attempts and no change in attempting to reach IVR. Either silence on line, a three rising tone, or fast busy; but no response to any of asterisk button and varying states of the above three states.
Turned off Norton Int Sec completely and no Windows Firewall (as done previously), reset Int Explorer security settings to Low on Internet and Local Low. Logged into PAP2 admin/admin. CYT30 changed to IP address which is used to access. XML server started, but never returns. Factory reset via reset button didn't help. Didn't try just the ethernet switch since obtaining the IP via IVR didn't seem possible. Did try changing PAP2 to hardcode the IP address assigned by router.
Perhaps I'll try CYT30 on another computer tomorrow. |
|
DSLHeadaches
join:2001-01-03
Woodland Hills, CA
·AT&T U-Verse
·VoiceStick
·RoadRunner Cable
| I was able to utilize another computer and CVT30 completed providing login info as designed. There must be some form of software blocking completion on my primary computer, the successful computer has almost nothing loaded.
I can now access the IVR, obtain IP and even have dialtone.
However, all attempts to login to Update or Voice_admin failed with "Error: User not allowed to login this user level" or "Bad User/Password". I've tried all sorts of combinations, power cycled the PAP2, tried normal login, followed by the /update page with no success (noting that it accepts the factory user/password at just the IP home page) and tried rerun CVT30 (all with internet diconnect). I'll keep trying... |
|
mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| said by DSLHeadaches :However, all attempts to login to Update or Voice_admin failed with "Error: User not allowed to login this user level" or "Bad User/Password". Once unlocked using CYT30 unlocker, use Admin/Admin combination to login to VM and/or perform firmware upgrade.
--
Mazi (UK Non-Geo Phone: +44-703-194-2574) |
|
DSLHeadaches
join:2001-01-03
Woodland Hills, CA
·AT&T U-Verse
·VoiceStick
·RoadRunner Cable
| Thanks mazilo & rcilink, I'm in and able to use Internetcalls.com for callout. Trying to determine SIP inbound and whether it will work. Obtained copy of xml file with provisioning. Hoping to try skype using the SIP intermediary tool. Hoping to figure out best CODECs since Internetcalls has bad echo for callee, as others have mentioned. Tried setting Echo Cancellation, we'll see if that helps. |
|
mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
1 edit | said by DSLHeadaches :Hoping to try skype using the SIP intermediary tool. I believe you will need also need asterisk to do this unless the intermediary tool (uplink?) can do this by itself, won't you?
--
Mazi (UK Non-Geo Phone: +44-703-194-2574) |
|
nukleuz
Premium
join:2006-07-23
Columbia, MD
2 edits | i got it working too on the RTP300 trying to figure out what to use for incoming calls like how to get a number for incoming calls and all that.if anyone has been able to do that please let us know
thank you |
|
kgu2206
join:2005-10-03 | Any lucky to unlock with D-Link VTA-VR device?
Thanks |
|
mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| reply to nukleuz
said by nukleuz :i got it working too on the RTP300 trying to figure out what to use for incoming calls like how to get a number for incoming calls and all that. Check out StanaPhone.
--
Mazi (UK Non-Geo Phone: +44-703-194-2574) |
|
nukleuz
Premium
join:2006-07-23
Columbia, MD | ok thnx |
|
netmitra
join:2006-09-28
Sunnyvale, CA | reply to DSLHeadaches
Hi;
Was anybody able to unlock WRTP54G using cyt. I tried hard, but not luck |
|
netmitra
join:2006-09-28
Sunnyvale, CA
| Cant Unlock WRTP54G
Please help.
I am using cyt39c to unlock a Vonage WRTP54G with firmware 1.00.20. The cyt screen gets stuck here for ever.
____________________________________________________
CYT-Unlocker - Local network version v3.9c
Simple XML provision server is waiting for your device..
This should only take up to one minute.
If it takes more than one minute, you may stop the XML
provision server by pressing the [ESC] key.
----------------------------------------------------------
Press [esc] to exit.
STATUS: XML Server started. Your Device is: WRTP54G |
|
mazilo
From Mazilo
Premium
join:2002-05-30
Lilburn, GA
| reply to netmitra
Re: CYT Device: Unlocking Information
said by netmitra :Was anybody able to unlock WRTP54G using cyt. I tried hard, but not luck Can you perform a firmware upgrade on your WRTP54G? If so, then you can flash it with a modded -NA firmware.
--
Mazi (UK Non-Geo Phone: +44-703-194-2574) |
|
campbeln
@co.uk | reply to netmitra
Re: Cant Unlock WRTP54G
I'm having the same issue, anyone have a resolution to this one? |
|
campbeln
@co.uk
| reply to netmitra
GOT IT!
check out this link: »Devomit Vonage(?) from RTP300/WRTP54G
Which will direct you to this one (which worked for me):
»Getting a WRTp54G to take 3.1.17-NA... |
|
campbeln
@co.uk | reply to netmitra
Re: Cant Unlock WRTP54G
Agh, just remember to try and use the "user" account (with a default password of "tivonpw") if /update.html doesn't play nice for you! |
|
deskjockey
join:2005-04-17
Charlotte, NC | reply to netmitra
I had the same problem with Vonage D-Link. I went back to the CYT 3.5 and worked like a charm. |
|
