soportec
Premium
join:2006-01-06
| reply to IntraLink
Re: help with mikrotik
i have it on AP bridge , all data rates are selected, tried from a to b , pramble is both, power is on default, tried almost all channels.. any other thing to check? it can see signal but it dont send any. when i look at the interfaces i see that lan1 is (R) running and wlan1 is active but there is no (R) lan2 and lan3 are disabled.
--
dw7700 1.8 G11 IA300, dw4020 satmex5/1230 1.2 Buisness, dw7000 .74 satmex5 .74 pro |
|
IntraLink
Premium,MVM
join:2002-08-14
Utah Valley
| Well, maybe your wireless is running, but you don't have your LAN set up right?
The wireless will not show R until a client is associated.
For AP Bridge to forward packets you either have to route or Bridge that interface with an ethernet interface. |
|
soportec
Premium
join:2006-01-06
| reply to soportec
Flags: X - disabled, R - running
0 name="ISP" mtu=1500 mac-address=00:15:6D:53:94:77 arp=proxy-arp
disable-running-check=no interface-type=Atheros AR5213
radio-name="00156D539477" mode=ap-bridge ssid="SonagueraNet" area=""
frequency-mode=regulatory-domain country=united states antenna-gain=15
frequency=2442 band=2.4ghz-b scan-list=default rate-set=default
supported-rates-b=1Mbps,2Mbps,5.5Mbps,11Mbps
supported-rates-a/g=6Mbps,9Mbps,12Mbps,18Mbps,24Mbps,36Mbps,48Mbps,
54Mbps
basic-rates-b=1Mbps basic-rates-a/g=6Mbps max-station-count=2007
ack-timeout=dynamic tx-power-mode=default noise-floor-threshold=default
periodic-calibration=default burst-time=disabled
dfs-mode=no-radar-detect antenna-mode=ant-a wds-mode=dynamic
wds-default-bridge=none wds-ignore-ssid=no
update-stats-interval=disabled default-authentication=yes
default-forwarding=yes default-ap-tx-limit=0 default-client-tx-limit=0
hide-ssid=no security-profile=device4 disconnect-timeout=3s
on-fail-retry-time=100ms preamble-mode=both compression=no
allow-sharedkey=no
--
dw7700 1.8 G11 IA300, dw4020 satmex5/1230 1.2 Buisness, dw7000 .74 satmex5 .74 pro |
|
soportec
Premium
join:2006-01-06 | with a laptop right next to ap with a 8 dbi omni connected i see nothing ,, not even with net stumbler..
--
dw7700 1.8 G11 IA300, dw4020 satmex5/1230 1.2 Buisness, dw7000 .74 satmex5 .74 pro |
|
MarkSorensen
Premium
join:2002-05-21
Northern Cal
1 edit | Another good tool is MikroTik wireless debug logging:
»wiki.mikrotik.com/wiki/Wireless_Debug_Logs
But, if you're not seeing your AP at all... I wonder about your bridge or masquerade configuration |
|
soportec
Premium
join:2006-01-06
| Flags: X - disabled, I - inactive, D - dynamic
# INTERFACE BRIDGE PRIORITY PATH-COST
0 I wlan1 bridge1 0x80 10
1 ether1 bridge1 0x80 10
above is my bridge setting but it shows the wlan1 INACTIVE Why?
--
dw7700 1.8 G11 IA300, dw4020 satmex5/1230 1.2 Buisness, dw7000 .74 satmex5 .74 pro |
|
soportec
Premium
join:2006-01-06
| ok status.. i am using a toshiba A105-S4094 and i can not see the wireless signal my partner has a Dell 640M with VISTA and he can see the signal with his laptop. We have another laptop same as mine with xp pro and it cant see it either. What could this be? I have changed the mode , channel and nothing.. not even with my net stumbler.
my partner gets a ip from the router going to the mikrotik and is able to browse internet. (have bridge set up on router)
--
dw7700 1.8 G11 IA300, dw4020 satmex5/1230 1.2 Buisness, dw7000 .74 satmex5 .74 pro |
|
soportec
Premium
join:2006-01-06 | other note , i had to change the antenna to B instead of A |
|
soportec
Premium
join:2006-01-06
| one other question , what package should be installed on the router . wireless or wireless legacy? i i try to put both on it disables one or the other
--
dw7700 1.8 G11 IA300, dw4020 satmex5/1230 1.2 Buisness, dw7000 .74 satmex5 .74 pro |
|
