NormanS
Premium,MVM
join:2001-02-14
San Jose, CA
 ·Pacific Bell - SBC
| reply to AlphaOne
Re: [DSL] ATT DSL - Change from Speedstream 5360 to 4100
said by AlphaOne  :Isn't it that the default 4100 config is PPPoE in the modem? I am not in a position to test this, but I am told that adding the SS4100 in place of an existing DSL modem "just works". The modem will detect the PPPoE session connection from the PPPoE client, and will self-configure in bridge mode. So I am told. Wish I had heard that when I replaced the old Westell WireSpeed B90-36R516. I would have just plugged in the new SpeedStream 4100 to test that report.
--
Norman
~Oh Lord, why have you come
~To Konnyu, with the Lion and the Drum |
|
kbuhagiar
join:2004-07-14
South San Francisco, CA
|  Thanks to all for the responses thus far.
I tried to swap modem-for-modem - no go.
The first three indicator lights (power-ethernet-DSL) of the 4100 get to green, but the 'Iternet' indicator stays dark. The 'Activity' light flickers occasionally. I left it connected for about 15 minutes, but status stayed the same.
I reconnected my 5360, and was somewhat concerned, since it took about 20 minutes before it was able to re-establish a connection and synch up.
Upon further review, something I neglected to mention in my earlier post is that I am one of those original early DSL customers who still has a Static IP address (which I believe means my service is not PPPoE). Can the 4100 be configured for Static IP service? Am I stuck with the 5360?
I was able to access the configuration screen for the 4100, but wasn't sure what to give for the login and password.
Any additional advice is greatly appreciated. Thanks! 
Ken in South San Francisco
at&t DSL |
|
tonydi
Premium,MVM
join:2001-05-11
San Jose, CA
1 edit | The login/password stuff is for the PPPoE setup, not Static. See if the info in this recent thread helps your situation...
»WRT54G - Static IP and 4100B modem in bridge mode - Help |
|
NormanS
Premium,MVM
join:2001-02-14
San Jose, CA
·Pacific Bell - SBC
| reply to kbuhagiar
said by kbuhagiar :Thanks to all for the responses thus far. I tried to swap modem-for-modem - no go. The first three indicator lights (power-ethernet-DSL) of the 4100 get to green, but the 'Iternet' indicator stays dark. The 'Activity' light flickers occasionally. I left it connected for about 15 minutes, but status stayed the same. When the SS4100 is in bridged mode, the Internet LED will remain dark. All that the Internet LED means is that the modem has established a PPP connection; it can't do that in bridged mode.
I reconnected my 5360, and was somewhat concerned, since it took about 20 minutes before it was able to re-establish a connection and synch up.
Upon further review, something I neglected to mention in my earlier post is that I am one of those original early DSL customers who still has a Static IP address (which I believe means my service is not PPPoE). Can the 4100 be configured for Static IP service? Am I stuck with the 5360?
It probably failed to "just work" because it did not detect the non-existent PPP session. In which case, your best option is to access the SS4100 config pages (index at 192.168.0.1) and manually bridge the modem.
I was able to access the configuration screen for the 4100, but wasn't sure what to give for the login and password. Any additional advice is greatly appreciated. Thanks!
You want to access the "PPP Location" pages, and select the "Bridged Mode" option.
--
Norman
~Oh Lord, why have you come
~To Konnyu, with the Lion and the Drum |
|
Helpful Tips
@telnor.net
| reply to kbuhagiar
the SS4100 modem came from factory with PPPoE on modem,
as you said before, you have static ip setup in your connection, first you need to place the modem on bridge mode if you have static ip's setup in a router or in your computer, first open IE and type in 192.168.0.1, then select advance then select connection configuration and change the network settings to non public ip's and save settings, then select PPP location and select bridge mode and save settings, then wait for the P E D become solid green, then you can connect the modem to the router and you are set, but if you still having issues call the help desk and ask to be transfer to second tier support, because they can check for more specific info on that type of modem, and it is fully supported by them, or if or you can migrate your account at help.sbcglobal.net/register, and there you can create a user name and password and create a PPPoE connection on the modem, if you want to access the modem after you place the modem on bridge mode, you need to reset the modem to be able to access the modem one more time, for that you need to press the reset button for 5 seconds, be careful not to turn off the modem on the reset process takes place, because it will burn out the modem. |
|
kbuhagiar
join:2004-07-14
South San Francisco, CA
| Thanks to all who have responded to my posts.
UPDATE: I placed the modem in bridge mode and all is now well - the new modem is working great, and I swear that its a little bit faster than the old 5360 it replaced.
Thanks again for the assistance!
Ken in South San Francisco, CA
AT&T/SBC/PacBell/Pacific Telephone DSL |
|
