bryanviper
join:2002-10-12
Toronto, CAN
 ·TekSavvy Solutions..
·Nothing But Net
|  Phone jack Wires Question
THis is how i have it hooked up using 2 wires. | 
This is my phone jack. |
This is what I'm doing.
Cat6 (from Demarc outside) ---> Phone jack in my office.
I used the Green/Green White wires to connect to the Demarc & have tried different combos on the jack but nothing seems to work? What wires go to what?
Should I be using 4 wires instead?
here are some pics so you know what im talking about.
Thanks
--
Computer: Intel Quad Core, 2gb OCZ DDr2, 2x Plextor Burners, Corsair 620psu, Antec 900Case, 5mb DSL from teksavvy
»www.MaximumRepair.ca |
|
Angelo_
The Network Guy
Premium
join:2002-06-18 | you only need 2 wires the second pair you can leave off as a backup if the wire gets damaged you have a apir to switch to... but thats up to you. |
|
Candoo3
join:2005-01-24
·TekSavvy Solutions..
| reply to bryanviper
said by bryanviper  :I used the Green/Green White wires to connect to the Demarc & have tried different combos on the jack but nothing seems to work? What wires go to what? If I understand you correctly, and you're using this jack solely for the outgoing modem connection, then you would use the same CAT6 wires to connect to the red and green terminals at the jack. The yellow and black should be redundant. Correct me if I am wrong. |
|
bryanviper
join:2002-10-12
Toronto, CAN
·TekSavvy Solutions..
·Nothing But Net
| said by Candoo3 :said by bryanviper :I used the Green/Green White wires to connect to the Demarc & have tried different combos on the jack but nothing seems to work? What wires go to what? If I understand you correctly, and you're using this jack solely for the outgoing modem connection, then you would use the same CAT6 wires to connect to the red and green terminals at the jack. The yellow and black should be redundant. Correct me if I am wrong. yup exactly. I wil try to re strip the cable and do it again on Red & green. Hopefully it was just a bad strip or something.
I'll let you guys know.
Thanks
--
Computer: Intel Quad Core, 2gb OCZ DDr2, 2x Plextor Burners, Corsair 620psu, Antec 900Case, 5mb DSL from teksavvy
»www.MaximumRepair.ca |
|
bryanviper
join:2002-10-12
Toronto, CAN | Still not working for some reason guys.
Re did all connections still nothing. no dial tone from the new jack.
Any ideas? |
|
TheMG
join:2007-09-04
Edmonton, AB
·TekSavvy Solutions..
 ·800Hosting.com
·Dreamhost
·TELUS
 ·Shaw
| reply to bryanviper
Green wire in the demarc should connect to the green wire in the jack, red wire to the red wire.
Make sure you know which wires in the CAT5e cable you are using so you make the right connections at each end.
If you suspect the cable is bad, you can tie the two wires of the pair together at one end and then check continuity with an ohmmeter at the other. |
|
bryanviper
join:2002-10-12
Toronto, CAN
·TekSavvy Solutions..
·Nothing But Net
| reply to bryanviper
here are some pics of what I did. Am I doing something wrong?
Thanks |
|
Angelo_
The Network Guy
Premium
join:2002-06-18 | the cat 5 the protecting sheilding needs to be removed |
|
bryanviper
join:2002-10-12
Toronto, CAN | The plastic covering over the wire correct? I had done that before but it did not work. Also its not 1 copper cable under the plastic covering. its a bunch of small thing ones. |
|
bryanviper
join:2002-10-12
Toronto, CAN | reply to TheMG
I dont have an ohmmeter, or else that would be perfect lol  |
|
Angelo_
The Network Guy
Premium
join:2002-06-18 | yes... and inside how is it connected to the phone system.
the colours can be crossed perhaps lets look at this step by step post the other end also
also dud the wire get damaged? |
|
bryanviper
join:2002-10-12
Toronto, CAN
·TekSavvy Solutions..
·Nothing But Net
| The other lines going into my home should not matter because this Cat6 is going directly to 1 jack for my DSL Modem and nothing else.
here are some pics of the jack. |
|
sMURF
join:2007-02-27
Toronto, ON | reply to bryanviper
You need to strip those wires, otherwise it'll never work. Strip the green and white/green, twist the copper strands together, then connect them to the terminals. |
|
bryanviper
join:2002-10-12
Toronto, CAN | They are stripped but you cant see it because its under the screw. But I'll re-do them and twist the copper.
Thanks |
|
Angelo_
The Network Guy
Premium
join:2002-06-18 | where did you buy those copper ends? |
|
bryanviper
join:2002-10-12
Toronto, CAN | hmm if you mean in the phone jack, it just came with it... Got the jack and everything came in there. |
|
Angelo_
The Network Guy
Premium
join:2002-06-18 | oh damn... i wnated those ends  |
|
bryanviper
join:2002-10-12
Toronto, CAN | hehe sorry. Got the jack off a Bell tech and all that was in there. |
|
Candoo3
join:2005-01-24
·TekSavvy Solutions..
| reply to Angelo_
said by Angelo_ :oh damn... i wnated those ends The electric supply warehouse that I deal with, has started carrying network supplies as well, with lots of stuff. If you have one local to you, maybe wander in and see what they have, even in the regular electrical supplies. |
|
Angelo_
The Network Guy
Premium
join:2002-06-18 | i can't find those copper tip ends... i've been trying to buy these for over a year :/ |
|
