bilbobbra
| WLI-TX4-AG300N
Can this be used to connect an xbox 360 to a non buffalo router at decent speeds such as a netgear dgn2000? |
|
tipstir
join:2004-11-14
Enfield, CT | Why yes they can.. I have 6x buffalo products mix bag everything works with Trendent and Dlink no issues. Tip for you might want to go over to DD-WRT forums and see if you can use their popular firmware as I did it was 3 of my buffalo gear already. |
|
bilbobbra
| I have since ordered and they do indeed connect however the buffalo will only connect at 130Mbs, the setting in the netgear is up to 270. Is there a way to boost this?
What is this firmware you mentioned?
Thanks |
|
bilbobbr
join:2005-11-07
Isle of Man
| reply to tipstir
Will the WLI-TX4-AG300N only connect to a dual band router (one with 2.4 and 5GHz) at the full speed? Or should it connect to a 2.4GHz network at full speed using 20Hz x 2?
Or if I install the firmware you mentioned can I force the device to connect at 40Mhz?
Thanks |
|
tipstir
join:2004-11-14
Enfield, CT
 ·Cox HSI
| reply to bilbobbra
Wireless N 150MBps (actual speed) (300MBps chipset speed)
Wireless N 130MBps (actual speed) (260MBps chipset speed)
If you see 270MBPs link speed actual speed would be 1/2 that reported speed. 135MBps (actual speed)
130MBps, 135MBps and 150MBps is ideal.. |
|
tipstir
join:2004-11-14
Enfield, CT | reply to bilbobbr
Only time you use 5.3GHz if the 2.4GHz is crowded in your area.
Wireless N should use 40MHz some have it set to 20/40MHz. |
|
bilbobbr
join:2005-11-07
Isle of Man
| reply to tipstir
Thanks for the reply. The netgear on my pc reports connected at 2x at 270Mbps using channels 1 & 5.
The Buffalo reports connected at 1x at 130Mbps using only channel one?
Will that be the 'actual' speed reported by the buffalo and will that be the same speed as the netgear which is saying 270? Or would the Buffalo be saying connected at 2x if it was at full speed?
Thanks for your help. |
|
lodestar
join:2005-08-23
England
1 edit | From what I can find of the spec for the WLI-TX4-AG300N on the web, this seems to be an important point
"...Four Built-in 10/100 Ports for up to 4 Simultaneous Wired Devices..."
So it seems to me that it does not matter what the reported wireless speed is. Devices plugged into the WLI-TX4-AG300N lan ports are limited to a maximum speed of 100Mbps. And of course although an operating system may show a 10/100 port as running or linked at 100Mbps in reality actual transfer speeds are more likely to be in the 60-70Mbps range.
In my opinon Buffalo should have fitted gigabit lan ports to the WLI-TX4-AG300N, that is 10/100/1000 speed which would at least have allowed wireless transfer rates in the 100Mbps+ range to have actually meant something. |
|
bilbobbr
join:2005-11-07
Isle of Man | That is a very good point. Isn't the actual throughput you get from wireless connected at 130Mbps a lot less than you would get from a wired 100Mbps though? |
|
lodestar
join:2005-08-23
England
1 edit | Yes I would have thought so, and Buffalo seem to be recognising that by only supplying 10/100 lan ports. I was intending to buy the WLI-TX4-AG300N for use with my Buffalo WZR-AG300NH router which does have gigabit lan ports. So it might well be able to exceed 10/100 lan port speeds but would not be able to demonstrate that in partnership with the WLI-TX4-AG300N. |
|
tipstir
join:2004-11-14
Enfield, CT
·Cox HSI
| reply to bilbobbra
Remember one point here is talking about wireless not wired. You have wireless card adapter inside the device and wired chipset for 10/100. You can get 300mbps over the wireless. Wired ports 100mbps. Gets confusing. I have it both ways here 10/100 on Wireless N Router used as Wireless N Access Point. and 10/100/100 on N router. Speeds varies.. |
|
tipstir
join:2004-11-14
Enfield, CT
·Cox HSI
| reply to lodestar
The Gig LAN will only work at LAN speeds of the slower network device on your LAN. So if you have 100mbps and 1000mpbs then they'll fallback to that. I have that problem so I just place the 1000mbps on completely different setup. Since there is no 1000mbps for WAN yet even though routers have that feature. I only use my 1000mbps with Jumbo Frames on to transfer larger GIG files among themselves using the \\ipgig address. These desktops and servers have dual NICs. One is for the Megabyte WAN/LAN the other one is for GigLAN. |
|
bilbobbr
join:2005-11-07
Isle of Man
| reply to bilbobbra
»images.google.co.uk/imgres?imgur···26sa%3DN
This translated into English was the answer I was looking for. The manual I got with the device only showed you how to use the connection wizard and there were no further instructions on the cd that came with it. Cant believe it was a physical switch I needed to change which was so tiny I could hardly see it. Also can't belive there is no documentation for this device, or downloads on the Buffalo site. Ah well at least I got there in the end! |
|
tipstir
join:2004-11-14
Enfield, CT | That's in Asian Where did the heck you got that from? |
|
bilbobbr
join:2005-11-07
Isle of Man
| I saw that on the buffalo website, if I changed to a different region, asia there was a load more info on this product! Why cant this info be translated into english for people in other parts of the world? I used google to search and translate to find my answer. |
|
