dimas
join:2009-05-04
indonesia | how to connect speed stream 5100a in indonesia?
I have speedstrean 5100a, it's working fine when i used it in san diego, but when i'm back to Jakarta, Indonesia it's not working here. Please help me? |
|
graysonf
Premium,MVM
join:1999-07-16
Fort Lauderdale, FL | Well, for starters, the VPI/VCI settings between the two locations are probably different. Does this unit auto-detect them? If it does, it's not working. If it doesn't you have to know the correct values and configure this manually. |
|
dimas
join:2009-05-04
indonesia
1 edit | reply to dimas
I'm not sure if it's auto detected and I've tried from »Ameritech - SBC FAQ »Funhouse info on the original 5100a Modem including how to get at line stats but it doesn't working too because we're using ip 192.168.0.xx. Is there any idea? |
|
Doctor Olds
I Need A Remedy For What's Ailing Me.
Premium,VIP
join:2001-04-19
1970 442 W30
clubs:
| reply to graysonf
The SBC 5100a (060-E141-A01) is pre-configured to only work with eight (8) most popular Virtual Circuit pairs (aka VPI/VCI pairs).
• 0/35
• 8/35
• 0/43
• 8/43
• 0/51
• 8/51
• 0/59
• 8/59
This is seen in the Web Interface only after you add the 5100's MAC ID to the ARP table entries.
»Efficient Networks Forum FAQ »Can I see what the Web Interface of the SBC Customized 5100s look like?
»Ameritech - SBC FAQ »Funhouse info on the original 5100a Modem including how to get at line stats
Otherwise the Web Interface on a 5100 Bridge is not accessible with out the special ARP command as not all 5100 had a Web Interface that you could reach using »speedstream or not unless you manually add the IP of the 5100 Modem to your PCs ARP table entries.
Accessing the Web Management Interface on my SpeedStream 5100 or 5200
HTH
--
What’s the point of owning a supercar if you can’t scare yourself stupid from time to time? |
|
Doctor Olds
I Need A Remedy For What's Ailing Me.
Premium,VIP
join:2001-04-19
1970 442 W30
clubs:
| reply to dimas
The SBC 5100a (060-E141-A01) is preset to »10.0.0.1 and using 192.168.anything will not work as there is nothing at that IP address in the SBC 5100a (060-E141-A01). It is like dialing a phone number that does not exist then expecting it to ring and be answered (its not going to happen).
--
What’s the point of owning a supercar if you can’t scare yourself stupid from time to time? |
|
dimas
join:2009-05-04
indonesia
2 edits | Yes, it is what i saw when add the 5100's MAC ID to the ARP table entries. Honestly i don't understand much about this so i called the ISP and they sent their tech here yesterday, but they couldn't do anything too. They said they don't know the IP to open the HTML page. So what should i do next? Is my 5100a can't use in Indonesia or any other idea? Or can i change IP 10.0.0.1 to 192.168.xx.xx maybe? Thank you. |
|
wayjac
Premium,MVM
join:2001-12-22
Indy | Is the dsl light steady green?
If the dsl light is steady green have a look at the summary page when the atm circuit is up all the vcc's will be up |
|
Doctor Olds
I Need A Remedy For What's Ailing Me.
Premium,VIP
join:2001-04-19
1970 442 W30
clubs:
| reply to dimas
You need to find out what the VPI/VCI is for the Indonesian ISP.
You need to know if it is "Annex A" ADSL or "Annex B" DSL. The SBC 5100a only works with "Annex A" DSL.
No, you cannot change the IP of the Modem. It normally doesn't have an IP Address anyway, as the ARP Table entry is not present by default.
--
What’s the point of owning a supercar if you can’t scare yourself stupid from time to time? |
|
dimas
join:2009-05-04
indonesia | Thanks a lot Guys.. |
|
dimas
join:2009-05-04
indonesia
| reply to Doctor Olds
said by Doctor Olds  :You need to find out what the VPI/VCI is for the Indonesian ISP. You need to know if it is "Annex A" ADSL or "Annex B" DSL. The SBC 5100a only works with "Annex A" DSL. No, you cannot change the IP of the Modem. It normally doesn't have an IP Address anyway, as the ARP Table entry is not present by default. VPI/VCI in my country is VPI 0 VCI 35, and using "Annex A" ADSL. I have a router Netgear WGT624 v2 too, Would it be easier to configure my 5100a if i use Router Netgear WGT 624 v2, please help me how to use this ADSL modem with this Router. Thank you
|
|
Doctor Olds
I Need A Remedy For What's Ailing Me.
Premium,VIP
join:2001-04-19
1970 442 W30
clubs:
| The 5100a is a Bridge Modem and there is nothing to configure. Especially since it already comes with the correct VPI/VCI it would plug into the Telephone Line then sync up showing a Solid Green DSL LED if the ISP has setup your DSL wiring at the Remote or local DSLAM. What do the LEDs show when it is plugged into the phone jack and powered on?
»SBC DSL FAQ »What are the lights and what do they mean?
As to what configuration your Netgear would need depends on what requirements your DSL ISP has to make a connection (Either DHCP or PPPoE). You would have to ask them what type of DSL setup they are using and follow the setup prompts in the Netgear.
--
What’s the point of owning a supercar if you can’t scare yourself stupid from time to time? |
|
dimas
join:2009-05-04
indonesia
1 edit | I'm sorry this is what i see when i enter to web interface, (on attachments). I'm so sorry that i missed, is not UP but NOT TRAINED. VPI/VCI pair in my country is :
1/32
0/33
0/35
0/100
8/35
8/48
0/38 |
|
Doctor Olds
I Need A Remedy For What's Ailing Me.
Premium,VIP
join:2001-04-19
1970 442 W30
clubs:
1 edit | What is the DSL LED doing? If the DSL LED is not solid green, then they have not installed the DSL yet. Not Trained means the Modem does not see any DSL Signal.
|
|
wayjac
Premium,MVM
join:2001-12-22
Indy
 ·AT&T Midwest
| reply to dimas
One other thing to consider........
The 5100a must have the dsl signal on the inner pair of the phone wiring
If the DSL signal is on the outer pair of the phone wiring that needs to be corrected
Switching inner and outer wire pairs on an RJ-11 wall plate |
|
dimas
join:2009-05-04
indonesia
1 edit | reply to Doctor Olds
Yes when i plug-in the DSL cable the dsl light is steady green then i look at the summary page and the atm circuit is all up.
And please tell me how to setting up the TCP IP after this, DNS SERVER in here they are using 203.130.xxx.xxx.
Here is the summary of my friend dsl modem, he's using TP_LINK.
How to config the TCP IP seting? |
|
Doctor Olds
I Need A Remedy For What's Ailing Me.
Premium,VIP
join:2001-04-19
1970 442 W30
clubs:
| You need your setup info from the ISP. I have no idea if they use Static IPs or DHCP IPs. The 5100a is a Bridge and doesn't have a Router so it only supports one (1) PC. You put your ISP setting into your PCs Ethernet Adapter TCP/IP settings page.
Select your LAN - Ethernet Adapter
Under TCP-IP Properties, either leaving all fields blank for DHCP DSL or fill in IPs supplied by your ISP for your account.
--
What’s the point of owning a supercar if you can’t scare yourself stupid from time to time? |
|
dimas
join:2009-05-04
indonesia
1 edit | My friends told me that my ISP is using 192.168.1.1, so what does it means? and where i put this value?
PS. I forgot, i've try to connect without fill any value on TCP IP Setting and fail. |
|
Doctor Olds
I Need A Remedy For What's Ailing Me.
Premium,VIP
join:2001-04-19
1970 442 W30
clubs:
| I would say that your friends are just wild guessing and don't really know since 192.168.1.1 is a Private IP that does not route out on the Internet as it is reserved for Home Networks and Private LAN Use.
Call your ISP and get the info, after all you are paying them for service and support. Get your monies worth.
--
What’s the point of owning a supercar if you can’t scare yourself stupid from time to time? |
|
dimas
join:2009-05-04
indonesia | OK thank you Doctor Olds and all..... |
|
dimas
join:2009-05-04
indonesia | Thanks Doctor Olds, wayjac and graysonf. Now i can use this modem. Just using new connection and choose PPOE connection and fill the username and password after those all it's working. Special thanks to Doctor Olds. |
|
