dslreports logo
site
 
    All Forums Hot Topics Gallery
spc

spacer




how-to block ads


Search Topic:
uniqs
4
share rss forum feed

jandrfas

join:2007-08-23
Downey, CA
reply to xrayman

Re: New Sprint 4G user - mediocre to poor speeds

said by xrayman:

Use a Wireless Access Point connected with cat5 cable to get the WiFi RF away from the modem.

»cgi.ebay.com/NETGEAR-WG602NA-54M···92wt_905
»www.dd-wrt.com/wiki/index.php/Wi···ss_Point

Thanks for the suggestion. It is one possibility that I can explore. I have a Linksys WRT54G that I've been using for my DSL (which will go away if I get the Sprint 4G to work). I assume I can probably use that as a WAP?


xrayman

join:2008-12-09
Kansas City
kudos:1

I installed dd-wrt on my WRT54GL, set up for WAP, 100ft of cat5 to modem on top of my house, works great!
Check the list to see if your router will work with dd-wrt firmware.
»www.dd-wrt.com/wiki/index.php/Su···_Devices

Before you try to take any actions, including loading any firmware to your router....read the English Broadcom Forum Announcement entitled Peacock Thread
»www.dd-wrt.com/phpBB2/viewtopic.php?t=51486
It contains more information than just for those who are having problems. Unfortunately, skipping any steps may lead to bricking (break) your router.



dib22

join:2002-01-27
Kansas City, MO
reply to jandrfas

said by jandrfas:

I assume I can probably use that as a WAP?

For simple testing just run an ethernet cable from one of the lan ports on the cradlepoint to the wan port on the WRT54G (where your dsl plugs in now). No re-configs should be needed, but you might need to power cycle the linksys for it to pull a new ip address from the cradlepoint.

jandrfas

join:2007-08-23
Downey, CA

I am up and running. The USB extension cable did the trick. I started with a 4' cable but was still having some interference issues. Ended up with a 12' cable which works out well for my situation (good spot for the router and modem based on best hotspot and availability of electrical outlets, etc.). I'm now getting average download speeds in the 6 - 7 range with occasional excursions to 10, and upload speeds consistently around 0.9 - 1.3. I'm going to let it run for a week or so, and if I get any sort of reliability out of it then I'm going to pull the plug on my DSL.

Now all I have to do is come up with a way to keep the modem where it belongs. Right now it's just sitting on top of a piece of furniture and has already been knocked off a few times. I'm thinking I'll pick up one if their USB Performance Docks on eBay - not that I need a signal boost at my location, but it looks like a good solution to keeping everything where it needs to be.

Thanks to everyone for all the help! I think I'm going to be very happy with my new Internet setup.


jandrfas

join:2007-08-23
Downey, CA
reply to dib22

said by dib22:

said by jandrfas:

I assume I can probably use that as a WAP?

For simple testing just run an ethernet cable from one of the lan ports on the cradlepoint to the wan port on the WRT54G (where your dsl plugs in now). No re-configs should be needed, but you might need to power cycle the linksys for it to pull a new ip address from the cradlepoint.

Here's a slightly off the wall question. To get the optimal 4G signal and speeds, I had to set up the Cradlepoint router and Sprint modem in a different room than my old DSL modem and router. The new location does not have ethernet connectivity. Now that my network is set up, I need to get a desktop PC connected to it. Previously the desktop was located in the same room as the router and connected via ethernet cable.

The obvious solution is go buy a wireless adapter for the desktop. They're relatively inexpensive and install in minutes. On the other hand, I can't help but think that I now have a perfectly good WRT54G that will just end up in storage, so why can't I re-configure it as a wireless adapter and save myself a few bucks? Is there a relatively straight forward way to do that? I've read up on the various third party firmware packages (dd-wrt, tomato, etc.) but I'm not very network savvy and don't want to brick the router, and I tend to not have a lot of patience with these things at home (I get enough frustration at work).


xrayman

join:2008-12-09
Kansas City
kudos:1

Using the stock WRT54G router in bridge mode, I don't think it is possible. I would get a low cost wireless adapter to use on the desktop.



dib22

join:2002-01-27
Kansas City, MO
reply to jandrfas

I'm with xray on that... while it might be technically possible (with some custom firmware on the linksys)... is suspect it would be work. A wifi adapter might kill 2 birds (just get one with the little stand you are after included ).

I am not much of a fan of wifi on stationary computers. I try to ethernet everything but my phones and laptops.

Check your baseboards, many have gaps at the bottom through which you can stuff and tuck an ethernet cable where it can't be seen. Many times I've seen people do this to avoid drilling or dropping cable through the walls. If the total distance (including weird dips around doors etc) is very far consider having someone just make you the ethernet cable... as pre-built ones get pretty expensive once you hit the 100foot mark, plus a custom built one will be the thinner in-wall cable and might fit better in the baseboard gap.


jandrfas

join:2007-08-23
Downey, CA

Success!

I decided to bite the bullet and try the dd-wrt upgrade. Figured I had nothing to lose. If it worked I saved myself the expense of a USB wifi device, plus perhaps some frustration (my experience with those is that they aren't particularly stable). If I bricked the router I figured no big loss - I didn't have a use for it anyway. The upgrade was actually fairly easy. The dd-wrt instructions are a bit intimidating at first, but if you spend an hour doing your homework and downloading the right files for your router it isn't bad at all. Now I have a very stable wireless connection to the main router and everybody is happy!



dib22

join:2002-01-27
Kansas City, MO

said by jandrfas:

Success!

You took the work route, but it sounds like you enjoyed it. Enjoy your speeds and think of us stuck on evdo while you stream that netflix


xrayman

join:2008-12-09
Kansas City
kudos:1
reply to jandrfas

said by jandrfas:

Success!
If I bricked the router I figured no big loss - I didn't have a use for it anyway. The upgrade was actually fairly easy.

Great that it worked for you. I have been very impressed with the versatility of the dd-wrt firmware. I have flashed several brands of routers with may versions of dd-wrt and never have lost a router. Just follow the instructions!


xrayman

join:2008-12-09
Kansas City
kudos:1
reply to dib22

said by dib22:

said by jandrfas:

Success!

think of us stuck on evdo while you stream that netflix

You can't get Sprint 4G or Clear in Kansas City?


dib22

join:2002-01-27
Kansas City, MO

said by xrayman:

You can't get Sprint 4G or Clear in Kansas City?

In the city, sure, but I'm on the road in the Kansas, Missouri, Oklahoma rural areas... no coverage...