The Site > Old Forums > AT&T Midwest > Get sync rates from 5260 through a router

These instructions are for a Linksys router, but should work for any router that allows you to set the WAN IP and disable automatic login

Status
Disconnect
Setup
Specify an IP address
IP = 10.0.0.2
Mask = 255.0.0.0
Gateway = 10.0.0.1
Login
Disable
Apply
In a dos window
telnet 10.0.0.1

Command-> show atminfo
--- ATM Information
UNI supported - Private UNI
AAL's supported - AAL5
Configured VCC - 1
Max VCI - 65535
VCI bits available - 16
Transmit Receive
Bandwidth : Allocated (cps) 0 0
Available (cps) 679 4150
Total (cps) 679 4150
Total (bps) 288000 1760000

--- Port Information
Port State - In Service
Transmit Port Speed (bps)- 288000
Receive Port Speed (bps) - 1760000
Factory ESI address - 00:20:ea:1b:38:b9
Hardware Interface Name - SpeedStream 5260-R:ENI
Hardware Interface Desc - Motorola 850 SAR Alcatel/RT Adapter
Hardware Serial Number - 1783993
Hardware Revision Number - 00010001
Hardware Instance Number - 0
Driver Name - enatm0
-- Press any key to continue --
Driver Description - ATM NIC Driver
Driver Serial Number - None
Driver Revision Number - 2.0.1 (46)
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

Transmit and receive port speeds are the sync rates
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
other things you can look at
Command-> show atmstats

--- AAL5 Statistics Transmit Receive
SDUs 355869 424993
Cells 1408509 7597832
Octets 59869071 355937307
Errors 0 2
Discards 0 0
SAR timeouts 0
CRC errors 2
Oversized SDUs 0 0

--- ATM Statistics Transmit Receive
Cells 1408514 7597901
Dropped Cells 1
Invalid VC Cells 1
Uncorrectable HEC Cells 0

Command->
Command-> help
----------------------------------------------------------------------------
usage: help
----------------------------------------------------------------------------
At the command prompt:

? Displays the top-level command set.

? Displays help for the command .

ESC- or Scrolls through the last commands executed.
ESC+ Type ENTER to execute the command displayed.

CTRL-U Erases the input on the command line.

When being prompted for a command argument:

+ or - Scrolls through the keywords. This control
only works for arguments that are keywords.

Note that the Command-> prompt will change to:

post_error->

-- Press any key to continue --
if there are software errors after reboot. You can view the
error messages on the serial console by logging in via the serial port.

Command-> ?

----------------------------------------------------------------------------
Command Description
----------------------------------------------------------------------------
show Shows system information, status, IP configuration
set Sets configuration parameters
delete Deletes NAPT server entries, routes, or PVCs
default Sets various parameters to factory defaults
clear Clears statistics
reboot Reboots the router
firmware Downloads new firmware to the router
getconfig Set router configuration from a file
putconfig Save router configuration to a file
quit (exit, logout, logoff) exits command session
logout (exit, logout, logoff) exits command session
logoff (exit, logout, logoff) exits command session
exit (exit, logout, logoff) exits command session
atmping Tests the ATM link by transmitting an OAM loopback cell
ping Sends datagram round-trip to specified IP host
traceroute Traces the route (hops) from the router to an IP address
Command-> show

--- General Bridge Information
System Mode - Bridge
System Type - SpeedStream 5260-R:ENI
System HW Version - 0
System Up Time - 17 Days 3 Hours 8 Minutes 24 Seconds
Software Version - 2.0.1(46) Apr 2 2000 19:46:23
Factory MAC Address - 00:20:ea:1b:38:b9
DSL Phy Description - Motorola 850 SAR Alcatel/RT Adapter
DSL Phy Version -
DSL Interface State - Up
Spanning Tree Mode - Disabled
Bridging Filter Mode - Disabled
Ethernet Interface - 10.0.0.1/255.0.0.0

Command-> show ?

----------------------------------------------------------------------------
Command Description
----------------------------------------------------------------------------
arp Displays the Address Resolution Protocol (ARP) cache
atminfo Displays ATM and AAL5 information
atmstats Displays combined AAL5 and ATM statistics
bridge Displays current system mode (bridge or router)
bridgefilter Displays the Bridge Filter mode
bridgemac Displays the Bridge MAC address table
bridgestats Display bridge port statistics
cfg Displays user-configurable parameters
conn Displays connection information
dslinfo Displays the DSL interface info
dslstats Displays the DSL interface statistics
dslstatus Displays the DSL interface status
ethcfg Displays Ethernet configuration
ethip Displays Ethernet IP Address configuration
ethstats Displays Ethernet statistics
ethstatus Displays Ethernet status
hostname Displays the modem hostname
icmpstats Displays ICMP statistics
ip Displays IP information for all devices
-- Press any key to continue --
ipgateway Displays IP gateway (default router) configuration
ipstats Displays IP statistics
spantree Display spanning tree information
spantreestatus Display spanning tree information
tcpstats Displays TCP statistics
udpstats Displays UDP statistics
vc Displays VC information
vcstats Displays AAL connection info per VC
--
Jim Anderson